• Journal of the Korean Chemical Society
• /
• v.60 no.5
• /
• pp.317-320
• /
• 2016

Efficient copper removal from water was achieved by using surface modified silica spheres with 3-mercaptopropyltrimethoxysilane (MPTMS) using base catalyst. The surface modification of silica spheres was performed by hydrolysis and condensation reactions of the MPTMS. The characteristic infrared absorption peaks at 2929, 1454, and 1343 cm⁻¹ represent the −CH₂ stretching vibration, asymmetric deformation, and deformation, respectively. The absorption peaks at 2580 and 693 cm⁻¹ corresponding the −SH stretching vibration and the C-S stretching vibration indicate the incorporation of MPTMS to the surface of silica spheres. Field emission scanning electron microscope (FESEM) image of the surface modified silica sphere (SMSS) shows nano-particles of MPTMS on the surface of silica spheres. High concentration of copper solution (1000 ppm) was used to test the copper removal efficiency and uptake capacity. The FESEM image of SMSS treated with the copper solution shows large number of copper lumps on the surface of SMSS. The copper concentration drastically decreased with increasing the amount of SMSS. The residual copper concentrations were analyzed using inductively coupled plasma mass spectrometer. The copper removal efficiency and uptake capacity with 1000 ppm of copper solution were 99.99 % and 125 mg/g, respectively.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.23 no.1
• /
• pp.79-84
• /
• 2007

Mineral Trioxide Aggregate(MTA) has been used in Endodontic treatment successfully for more than 10 years. But the high cost of MTA limits its use in endodontics in Korea. Recently many studies have been done to compare MTA and Portland cements. To investigate the chemical constitutions of MTA (Proroot MTA, Tulsa Dental), Gray Portland cement (Lafarge Halla cement), White Portland cement(Union corp), and fast setting cement (SSangyong cement), we performed SEM(scanning electron microscope)(S4700, Hitachi) examination and EDS(Energy dispersive spectrometry)(emax, Horiba) analysis. SEM examination and EDS analysis were committed to and performed in SNU DRI (Seoul National University Dental Research Institute). We found that particles of MTA were relatively round, uniform in size, and compactly packed compared to Portland cements. Chemical constitutions of MTA, GPC, WPC and FSC were similar. It was shown that MTA contains much BiO2 . MTA and WPC showed less heavy metals such as Fe and Mg compared to GPC and FSC. FSC showed remarkably high aluminum content.

• Korean Journal of Environmental Agriculture
• /
• v.15 no.4
• /
• pp.494-500
• /
• 1996

To investigate the relationship between the atmospheric pollution level and the pollution level of soil adjacent to the roadside in Suwon suspended particles and soil samples were collected in August to October 1993, and analyzed by AAS and ICP. The Ca, K, Mg concentration in atmosphere were observed as high level and assumed that it was effected by the acid-rain originated from the erosion of concreate vicinity to the roadside, and the Pb, Zn concentration were higher at outer area than that of central area. Hazardous heavy metal (Cu, Pb, Zn) concentrations in soil were observed as high level at all sampling sites. The relationship between the heavy metal concentrations in the atmosphere and those in the soil were analyzed, by using the correlation coefficient value(r) and the result was appeared similarly. And this study indicated that the atmospheric pollution affect the level of the soil pollution adjacent to the road side.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.313-317
• /
• 2010

Li, Zr doped mesoporous silica was synthesized in one pot and investigated for low temperature $CO_2$ adsorption. Herein CTAB and TEOS are used as structural directing agent and silica source respectively. The characteristics of the material was obtained from FT IR, XRD, SEM, TG and BET results. ICP AES results revealed the presence of lithium and zirconium. The material possesses high surface area ($962.22m^2g^{-1}$) with mono dispersed particles of about 2 nm. The maximum $CO_2$ adsorption capacity is 5 wt % (50 mg/g) of $CO_2$/g of sorbent at $25^{\circ}C$, which is regenerable at $200^{\circ}C$. This regeneration temperature of the adsorbent is lower than the reported lithium zirconium silicate powder. Until now, there is no report for the synthesis of Li, Zr doped mesoporous silica. The performance studies illustrate that Li, Zr doped mesoporous silica is tunable, regenerable, recyclable and selective sorbent and hence found to be a promising candidate for $CO_2$ adsorption.

• ALGAE
• /
• v.27 no.2
• /
• pp.115-123
• /
• 2012

The establishment of algal spores plays an essential role in adult kelp distribution and abundance patterns. Sedimentation is a key variable regulating algal spore settlement and success, possibly controlling species-specific dominance $in$ $situ$. Laboratory experiments were used to determine spore attachment and survival rates of two Alaskan canopy-forming kelps, $Nereocystis$ $luetkeana$ (K. Mertens) Postels & Ruprecht and $Eualaria$ $fistulosa$ (Postels & Ruprecht) M. J. Wynne, to various types of sediment loading. Spore attachment for both species was significantly and similarly affected by three sediment treatments: suspended particles; settled sediment covering the substratum; and smothering of attached spores by settling sediment. Spore attachment decreased by approximately 90% at 420 mg sediment $L^{-1}$, the highest sediment load tested here, under all three treatments for both species. These results suggest that increases in sedimentation may constrain the success of the spore stages, but sediment does not seem to be a likely factor explaining species-specific distribution patterns. However, while sedimentation affected spores of both species similarly, timing of spore release in relation to times of maximum sediment load in the water might differ for different species, possibly explaining kelp species distribution patterns.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.6
• /
• pp.735-741
• /
• 2010

A pilot test was carried out to investigate the long term operation characteristics of Microfiltration (MF) system as a pretreatment for seawater reverse osmosis (SWRO) processes for two years. A commercialized MF module with pressurized operation type was used to filter seawater to remove particles which can foul reverse osmosis (RO) membrane. Silt Density Index (SDI) values of filtered seawater by the MF system were ranged from 0.14 to 1.79, which meet the SDI standard for RO feed water as depicted in previous literatures. Although the tested seawater is quite clean (i.e., dissolved organic cabon (DOC) concentration and turbidity were about 1 mg/l and less than 1 NTU, respectively) enough not to foul the MF membrane, steep increase in trans-membrane pressure (TMP) with a constant flux were observed over a whole operation period. A set of operation and water analysis data implies that the steep increase in TMP was resulted from iron and maganese fouling by the combination of metal corrosion by seawater and oxidation state by aeration and residual chlorine.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.31-38
• /
• 2004

The main purpose of this study is to investigate the characteristics of hybrid collection system combined with centrifugal force of cyclone and filtration of bag filter in one unit system. The experiment and numerical simulation are executed for the analysis of collection efficiency and pressure drop characteristics of hybrid system in comparison with those of a general fabric bag filter with the various experimental parameters such as inlet velocity(filtration velocity), dust concentration and dust type, etc.. In present system, dust particles tangentially coming into the system body are controlled by the centrifugal force effect, and the next collection is made out by the filtration mechanism in the fabric filter media. Therefore, the effective first collection causes the decrease of dust loading on the fabric filter, and it presents quite a lower pressure drop of fabric filter than that of a general fabric filter. At the inlet velocity, $21{\sim}27m/sec$ and inlet concentration(fly ash) $300mg/m^3$, pressure drops through the filter media of hybrid system are shown lower as $10{\sim}22mmH_2O$ comparing to those($17{\sim}33mmH_2O$) of a general fabric bag filter.

• Journal of Powder Materials
• /
• v.16 no.4
• /
• pp.280-284
• /
• 2009

The pressureless sintering behavior of $Al_2O_3$/Cu powder mixtures, prepared from $Al_2O_3$/CuO and $Al_2O_3$/Cu-nitrate, has been investigated. Microstructural observation revealed that $Al_2O_3$ powders with nano-sized Cu particles could be synthesized by hydrogen reduction method. The specimens, pressureless-sintered at $1400^{\circ}C$ for 4 min using infrared heating furnace with the heating rate of $200^{\circ}C$/min, showed the relative density of above 90%. Maximum hardness of 16.1 GPa was obtained in $Al_2O_3$/MgO/Cu nanocomposites. The nanocomposites exhibited the enhanced fracture toughness of 4.3-5.7 $MPa{\cdot}m^{1/2}$, compared with monolithic $Al_2O_3$. The mechanical properties were discussed in terms of microstructural characteristics.

• Advances in nano research
• /
• v.5 no.1
• /
• pp.27-34
• /
• 2017

One of the methods of removing cyanide from wastewater is surface adsorption. We simulated the removal of cyanide from a synthetic wastewater in the presence of Titanium dioxide nano-particles absorbent uses VISUAL MINTEQ 3.1 software. Our aim was to determine the factors affecting the adsorption of cyanide from synthetic wastewater applying simulation. Synthetic wastewater with a concentration of 100 mg/l of potassium cyanide was used for simulation. The amount of titanium dioxide was 1 g/l under the temperature of $25^{\circ}C$. The simulation was performed using an adsorption model of Freundlich and constant capacitance model. The results of simulation indicated that three factors including pH, nanoparticles of titanium dioxide and the primary concentration of cyanide affect the adsorption level of cyanide. The simulation and experimental results had a good agreement. Also by increasing the pH level of adsorption increases 11 units and then almost did not change. An increase in cyanide concentration, the adsorption level was decreased. In simulation process, rising the concentrations of titanium dioxide nanoparticles to 1 g/l, the rate of adsorption was increased and afterward no any change was observed. In all cases, the coefficient of determination between the experimental data and simulation data was above 0.9.

• Environmental Engineering Research
• /
• v.21 no.4
• /
• pp.427-435
• /
• 2016

In this study, change in water-dissolved oxygen (DO) was analyzed under various synthetic water qualities and nanobubbles (NBs) application conditions, such as gas type, initial DO as well as water dissolved, suspended and organic matters contents. When oxygen, rather than air, was introduced into nitrogen-desorbed ultra-pure water, the stagnation time was significantly increased. It took ten days for DO concentration to drop back to saturation. The higher the initial DO concentration, the longer particles were observed above saturation due to particle stability improvement. The oxygen mass transfer rate of 0.0482 mg/L/min was found to reach a maximum at an electrolytic concentration of 0.75 g/L, beyond which the transfer rate decreased due to adsorption of negative ions of the electrolyte at the interface. High levels of turbidity caused by suspended solids have become a barrier to dissolution of NBs oxygen into the water solution, and thus affected the transfer performance. On the other hand, by applying NBs for just an hour, up to 7.2% degradation of glucose as representative organic matter was achieved. Thus, NBs technology would maintain a high DO extent for an extended duration, and thus can improve water quality provided that water chemistry is closely monitored during its application.