• Korean Journal of Materials Research
• /
• 제12권12호
• /
• pp.904-910
• /
• 2002

Surface alloying using TiC, $TiB_2$ and VC ceramic particles on carbon steel has been performed using high voltage electron beam. Each type of ceramic particles was mixed with flux of Al and $MgF_2$ in 1 to 4 ratio. The microstructures of the surface alloyed layers consisted of melted region, interface region. heat affected region and the unaffected matrix. The surface layer of the TiC surface alloyed had a cubed primary and a eutectic type of TiC. $TiB_2$ in surface layer of $TiB_2$ surface alloyed were incompletely melted with$ TiB_2$ particles as observed before the alloying. On the surface layer of the VC surface alloyed, very well defined cell structure was observed with VC on the cell boundary. In addition, ~50 nm in diameter VC particles in high density were ubiquitous in the matrix. Those fine VC particles prominently improved the hardness and wear resistance of the surface layer of the VC surface alloyed.

• Journal of Korean Society of Water and Wastewater
• /
• 제30권1호
• /
• pp.33-40
• /
• 2016

In this study, a fluorescent silica nano particle is used as the surrogate for challenging test of membrane surface integrity. The particles are functionalized by a fluorescent dying agent so that as an ultraviolet light is imposed a bright fluorescent image from the particles can be taken. If a membrane surface is damaged and has a compromised part larger than the size of surrogate the fluorescent particles would pass through and contained in the permeate. An operator can directly notice whether the membrane surface is damaged or not by detecting a fluorescent image taken from the permeate. Additionally, the size of compromised part is estimated through analysing the fluorescent image in which we surmise the mass of particles included in the permeate by calculating an average RGB value of the image. The pilot scale experiments showed that this method could be applied successfully to determine if a membrane surface had a damaged parts regardless of the test condition. In the testing on the actual damaged area of $4.712mm^2$, the lowest error of estimating the damaged area was -1.32% with the surrogate concentration of 80 mg/L, flux of $40L/m^2/hr$ for 25 minutes of detection. A further study is still going on to increase the lowest detection limit and thus decrease the error of estimation.

• Journal of Korean Society for Atmospheric Environment
• /
• 제15권1호
• /
• pp.23-32
• /
• 1999

Deposition is one of the important removal mechanisms for the ambient aerosol, and it also leads to adverse environmental and economic impacts. The purpose of this study was to investigate chemical compositions and spatial distributions of fall-out aerosols. A total number of 340 samples were collected at 35 sampling sites in Suwon area from January to November, 1996. Twelve inorganic elements (Al, Ba, Cd, Cr, K, Pb, Sb, Zn, Cu, Fe, Ni, and V) and eight ionic components ($F^-$, Cl, $NO_3^-$, $SO_4^{2-}$, $Na^+$, $NH_4^+$, $Mg^{2+}$, and $Ca^{2+}$) were analyzed by AAS and IC, respectively. The monthly variation showed that the flux of fall-out particles was increased in the spring season(March, April, and May) and decreased from August to October. Arithmetic mean flux of fall-out particles was 176.8 kg/$ extrm{km}^2$/day during the study period. The fluxes of each chemical species were $SO_4^{2-}$ 12.414, $Ca^{2+}$ 7.369, $NO_3^-$ 5.812, $Cl^-$ 3.566, $NH_4^+$ 3.176, Fe 3.107 kg/$\textrm{km}^2$/day, and so on. By using a kriging analysis, spatial distribution pattern of those fluxes was intensively studied. Total fluxes estimated in Suwon city were 8424.72t/y of fall-out particles, 519.27t/y of $SO_4^{2-}$, 336.79t/y of $Ca^{2+}$,267.34 t/y of $NO_3^+$, 155.36t/y of $Cl^-$, 147.79t/y of Fe.

• Journal of Korean Society of Environmental Engineers
• /
• 제30권10호
• /
• pp.1028-1033
• /
• 2008

Sequential quick crushing and alkali hydrolysis(SeCAH), as a pretreatment for foodwaste, incorporating mechanical crushing and alkali hydrolysis was proposed and investigated in this study. Focuses were placed on the improvement of biodegradability of foodwaste and the estimation of potential inhibitors for anaerobic digestion. The solubility of the pretreated foodwaste by SeCAH was increased 2.5 times rather than mechanical crushing. Considering solubility improvement and energy consumption, 2,000 rpm of crushing strength and 5$\sim$10 sec of crushing time are recommended. After SeCAH, the fraction of large organic particles(>2.36 mm) of foodwaste was sharply decreased from 88.0% to 29.0%, otherwise the fraction of small particles(<75 $\mu$m) was greatly increased from 10.5% to 40.7%. Ammouinum, potassium and sulfate were estimated as potential inhibitors for anaerobic digestion and their concentrations in pig slurry were 3331.3 mg/L, 4256.5 mg/L and 1017.5 mg/L, respectively.

• Asian Journal of Atmospheric Environment
• /
• 제6권4호
• /
• pp.259-267
• /
• 2012

To clarify the effects of black carbon (BC) particles on growth and gas exchange rates of Asian forest tree species, the seedlings of Fagus crenata, Castanopsis sieboldii, Larix kaempferi and Cryptomeria japonica were exposed to BC particles with sub-micron size for two growing seasons from 1 June 2009 to 11 November 2010. The BC particles deposited after the exposure to BC were observed on the foliar surface of the 4 tree species. At the end of the experiment, the amount of BC accumulated on the foliar surface after the exposure to BC aerosols were 0.13, 0.69, 0.32 and 0.58 mg C $m^{-2}$ total leaf area in F. crenata, C. sieboldii, L. kaempferi and C. japonica seedlings, respectively. In August 2010, the exposure to BC particles did not significantly affect net photosynthetic rate under any light intensity, stomatal diffusive conductance to water vapour ($g_s$), stomatal limitation of photosynthesis, response of $g_s$ to increase in vapour pressure deficit and leaf temperature under light saturated condition in the leaves or needles of the seedlings. These results suggest that the BC particles deposited on the foliar surface did not reduce net photosynthesis by shading, did not increase leaf temperature by absorption of irradiation light, and did not induce plugging of stomata in the leaves or needles of the seedlings. There were no significant effects of BC particles on the increments of plant height and stem base diameter during the experimental period and the whole-plant dry mass at the end of the experiment. These results indicate that the exposure to BC particles with sub-micron size for two growing seasons did not significantly affect the growth and leaf or needle gas exchange rates of F. crenata, C. sieboldii, L. kaempferi and C. japonica seedlings.

• Journal of Surface Science and Engineering
• /
• 제50권3호
• /
• pp.212-218
• /
• 2017

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classifying with an ultrasonic wet-magnetic separation unit to get high pure nano-sized particles. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders resulted in producing the powders with average size of 800 nm. The addition of a surfactant during the wet-magnetic separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 800 nm size were 3651 A/m, $53.92Am^2/kg$ and $4.0Am^2/kg$, respectively.

• Journal of the Korean Ceramic Society
• /
• 제43권7호
• /
• pp.427-432
• /
• 2006

The preparation of SiC powder by SHS in the system of $SiO_2-Mg-C$ was investigated in this study. The effects of various processing parameters such as the initial pressure of inert gas in reactor, the content of Mg and C in mixture and the size of $SiO_2$ particles on the synthesis of SiC by SHS methode were investigated. The minimum initial pressure of inert gas in reactor for SHS reaction in this system was 5 atm, and as the pressure increased, and the concentration of unreacted Mg decreased. At 50 atm of the initial inert gas pressure in reactor, the optimum composition for the preparation of pure SiC was $SiO_2+2.5Mg+1.2C$. SiC powder synthesized in this condition had a mixture of ${\alpha}-SiC\;and\;{\beta}-SiC$ with an irregular shape and the particle size of $0.5{\sim}0.8{\mu}m$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.5-8
• /
• 2005

In this report the developing trends of several clean and green propellants have been summarized. A low-acid clean propellant has been developed, which substantially reduced the content of hydrochloric acid(HCl) in the solid rocket exhaust. Although the chlorine-free approach is now preferred, this technology has not been proved yet. Another acid suppression effect of Magnalium(Mg-Al Alloy) was investigated. Reports says that the concentration of HCl could be reduced to approximately one-fifth of conventional propellant. Many 'green' propellants with low toxicity are being developed for next-generation post-boost propulsion systems, in which combustion research on the Al or Mg fine metal particles with hot steam in various stoichiometric conditions are being performed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.201.2-201.2
• /
• 2016

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classified by ultrasonic wet-magnetic separation method to get nano-sized particles with high purity. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders produced the powders with average size of $3.7-0.8{\mu}m$. The addition of a surfactant during the separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 810 nm size were 45.89 Oe, 53.92 emu/gOe, 0.4 emu/Oe, respectively.

• Bulletin of the Korean Chemical Society
• /
• 제32권9호
• /
• pp.3453-3458
• /
• 2011

The $Mg_xZn_{1-x}O$ thin films with the various content ratio ranging from 0 to 0.4 were prepared by sol-gel spincoating method. To investigate the effects of content ratio on the structural and optical properties of the $Mg_xZn_{1-x}O$ thin films, scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoluminescence (PL) were carried out. With increase in the content ratio, the grain size of the $Mg_xZn_{1-x}O$ thin films was increased, however, at the content ratio above 0.2, MgO particles with cubic structure were formed on the surface of the $Mg_xZn_{1-x}O$ thin films, indicating that the Mg content exceeded its solubility limit in the thin films. The residual stress of the $Mg_xZn_{1-x}O$ thin films is increased with increase in the Mg mole fraction. In the PL investigations, the bandgap and the activation energy of the $Mg_xZn_{1-x}O$ thin films was increased with the Mg mole fraction.