• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.103-104
• /
• 2007

$CuInO_2$ 단일상은 합성조건이 매우 까다롭기 때문에 일반적인 고상법으로 얻기 힘든 것으로 알려저 있다. 투명전도성 $CuInO_2$ 박막을 증착하기 위하여 일반적인 고상법으로 Cu와 In의 비율이 1:1인 $Cu_2O-In_2O_3$ composite target 및 In 대신 Ca, Mg, Ti가 각각 1mol% 도핑된 target을 제작하였다. 제작된 각각의 composite target을 이용하여 pulsed laser deposition(PLD) 공정으로 투명전도성 $CuInO_2$ 박막을 증착하였다. Cu와 In이 1:1 인 $Cu_2O-In_2O_3$ composite target을 사용한 경우, 증착된 박막이 Cu와 In의 비율이 1:1인 c-axis 배향된 단일상의 $CuInO_2$ 박막임을 확인하였다.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.3
• /
• pp.6-10
• /
• 2003

Silver nano-powder was added to Ma $B_2$ to make (Ag)$_{(x)wt.%}$(Mg $B_2$)$_{(l00-x)wt.%}$ (A $g_{x}$-Mg $B_2$) (10 $\leq$ x $\leq$ 50) composite superconductors to investigate the effect of the Ag nano-powder on the vortex pinning. Pellets made out of the mixed powder were put inside stainless steel tubes, which were sintered at 85$0^{\circ}C$ in Ar atmosphere. No impurity phase was identified for as-rolled samples. However, both the Mg $B_2$ and the A $g_{x}$-Mg $B_2$ composite pellets, when sintered, contain small amount of Mg $B_4$ and MgAg impurity phases. From the magnetization study, it was found that the flux pinning was improved in the high magnetic field region (> 3 T) only when 10w/o Ag was added to Mg $B_2$. The "two step" structures in ZFC M(T) curve gradually increased as the amount of Ag added increased. Pinning centers can be created by adding a suitable amount of Ag nano-powder which is not too large to increase the decoupling between the Mg $B_2$ grains.crease the decoupling between the Mg $B_2$ grains.

• Journal of Powder Materials
• /
• v.16 no.6
• /
• pp.438-441
• /
• 2009

Mg-Cu composites were successively fabricated using a combination of rapid solidification and extrusion processes. In addition, the microstructural variation of the composite was investigated by performing the extrusion repeatedly. It resulted that the composite formed an uniform and dense structure by the extrusion, and the microstructure became fine as the extrusion conducted repeatedly. The microstructural variation was known to be dependent on the number of extrusion and the area reduction ratio. The tensile strength was also measured as a function of the microstructural variation.

• Journal of Powder Materials
• /
• v.16 no.3
• /
• pp.173-179
• /
• 2009

In the present study, Zr-base metallic glass(MG)/diamond composites are fabricated using a combination of gas-atomization and spark plasma sintering (SPS). The densification behaviors of mixtures of soft MG and hard diamond powders during consolidation process are investigated. The influence of mixture characteristics on the densification is discussed and several mechanism explaining the influence of diamond particles on consolidation behaviour are proposed. The experimental results show that consolidation is enhanced with increasing diamond/Metallic Glass(MG) size ratio, while the diamond fraction is fixed.

• Membrane and Water Treatment
• /
• v.10 no.5
• /
• pp.381-385
• /
• 2019

Surface modification is very efficient and scalable approach to achieve improved membrane performance. We treated Reverse Osmosis Thin Film Composite (TFC RO) membrane with various concentrations of Polyethylene Glycol (PEG), a hydrophilic polymer after activation with sodium hypochlorite. This treatment resulted in an increment of the water flux by 43% and the salt rejection by 2.36% for the 3000 mg/l PEG-treated membrane. Further, these PEG-treated membranes were exposed to a mixture of 3000 mg/l PEG and 1000 mg/l sodium hypochlorite for 1 hour. Further modification of this membrane by PEG and sodium hypochlorite mixture increased the water permeance up to 133% when compared with the virgin TFC RO membrane. We characterized the treated membranes to understand the changes in wettability by contact angle analysis, changes in surface morphology and roughness by scanning electron microscope (SEM) and atomic force microscope (AFM) analysis.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.243-248
• /
• 2014

Silicon-carbon composite was prepared by the magnesiothermic reduction of mesoporous silica and subsequent impregnation with a carbon precursor. This was applied for use as an anode material for high-performance lithium-ion batteries. Well-ordered mesoporous silica(SBA-15) was employed as a starting material for the mesoporous silicon, and sucrose was used as a carbon source. It was found that complete removal of by-products ($Mg_2Si$ and $Mg_2SiO_4$) formed by side reactions of silica and magnesium during the magnesiothermic reduction, was a crucial factor for successful formation of mesoporous silicon. Successful formation of the silicon-carbon composite was well confirmed by appropriate characterization tools (e.g., $N_2$ adsorption-desorption, small-angle X-ray scattering, X-ray diffraction, and thermogravimetric analyses). A lithium-ion battery was fabricated using the prepared silicon-carbon composite as the anode, and lithium foil as the counter-electrode. Electrochemical analysis revealed that the silicon-carbon composite showed better cycling stability than graphite, when used as the anode in the lithium-ion battery. This improvement could be due to the fact that carbon efficiently suppressed the change in volume of the silicon material caused by the charge-discharge cycle. This indicates that silicon-carbon composite, prepared via the magnesiothermic reduction and impregnation methods, could be an efficient anode material for lithium ion batteries.

• Membrane Journal
• /
• v.3 no.2
• /
• pp.70-78
• /
• 1993

The permeation of insulin was conducted through glucose oxidase(GOD) immobilized composite membrane composed of poly(vinyl akohol)/chitosan blend and porous polyamide membrane. The permeation coefficient of insulin through GOD-immobilized membrane was in the order of $10^{-6}{\sim}10^{-7}\textrm{cm}^3cm/\textrm{cm}^2sec$. The sensitivity of the composite membrane to the glucose concentration was high in a low glucose concentration resulting from the oxygen depletion from the membrane. The permeation of insulin through composite membrane made of PVA/chitosan and porous polyamide membrane was changed by pH and glucose concentration. The permeability was progressively increasing with the glucose concentration at least up to 500mg%.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.221.1-221
• /
• 2003

• Membrane Journal
• /
• v.20 no.2
• /
• pp.142-150
• /
• 2010

A series of anion exchange composite membranes were prepared and characterized for electrodialysis processes used in the removal of nitrate nitrogen and ions in groundwater. The membranes were prepared as follows; first, fabric substrates were fully impregnated with monomer mixtures of vinylbenzylchloride (VBC), divinylbenzene (DVB), Styrene (ST) and $\alpha,\alpha$-Azobis(isobutyronitrile) (AIBN). Second, they were thermally polymerized to yield crosslinked poly (VBCST- DVB)/fabric composite membranes. Finally, the membranes were treated with trimethylamine (TMA) / acetone to give $-N^+(CH_3)_3^-$-containing poly(VBC-ST-DVB)/fabric membranes. The basic membrane properties such as ion exchange capacity (IEC), electric resistance and water content of the resulting membranes were measured as a function of VBC/DVB and TMA/Acetone content. As a result, the composite membranes showed lower electric resistance and higher IEC than commercial anion exchange membranes (AMX, Astom). Electrodialysis tests using the prepared membranes were carried out for the removal of various ions such as $NaNO_3$, $MgSO_4$ and NaF for 60 minutes. The results showed that the ions were removed below 1 mg/L within about 15 minutes which indicates that the anion exchange membranes prepared here could be applied to the electrodialysis process. as can be seen in the following that the ion conductivity values were almost no change after 15 minutes electrodialysis.

• Advances in environmental research
• /
• v.6 no.3
• /
• pp.173-187
• /
• 2017

Heavy metals, such as vanadium, are some of the most toxic types of water contaminants. In this study, vanadium was removed using a new composite adsorbent called BAZLSC. The impacts of pH and initial concentration of vanadium(V) on the elimination effectiveness of this metal by using BAZLSC were investigated in the first step of the study. Vanadium removal increased as pH increased to 3-3.5, and initial concentration increased to 60-70 mg/L. The removal efficiency then decreased. Central composite design and response surface methodology were employed to examine experimental data. Initial concentration of V ($mg.L^{-1}$), pH, and dosage of adsorbent (g/L) were the independent factors. Based on RSM, the removal effectiveness of vanadium was 86.36% at the optimum of initial concentration (52.69 mg/L), pH (3.49), and adsorbent dosage (1.71 g/L). Also adsorption isotherm investigations displayed that the Freundlich isotherm could explain vanadium adsorption by BAZLSC better than the Langmuir isotherm. Beside them, desorption studies showed sorption was slightly diminished after six continuous cycles.