• Macromolecular Research
• /
• v.16 no.6
• /
• pp.524-531
• /
• 2008

The mitigation or elimination of methanol crossover for perfluorosulfonic acid fuel cell membranes has been investigated extensively for direct methanol fuel cell applications with the aim of increasing the electrochemical performance and enhancing the utilization rate of methanol. Self-assembly modifications by applying an oppositely charged polyelectrolyte to Nafion membranes were attempted in order to block or reduce methanol crossover while maintaining the other advantageous properties of Nafion membranes. It was reported that anionic polyallylamine hydrochloride (PAH) was the most efficient polyelectrolyte in reducing methanol crossover, and considerable cell performance was obtained even at a methanol feed concentration of 10 M.

• Fire Science and Engineering
• /
• v.25 no.2
• /
• pp.126-131
• /
• 2011

This study is intended to understand mass loss rate and air entrainment rate of the whirl fire by height of fire source. Liquid fuels were methanol and n-Heptane which are used in many studies of whirl fire. Size of vessel was 100 mm ${\times}$ 100 mm ${\times}$ 50 mm and the vessel was made by stainless steel. When height of fire source changed from 0 cm to 30 cm, air entrainment rate showed the fastest in case of 0 cm. And in the same height of fire source, average and maximum air entrainment rate showed the fastest in 30 cm of anemometer. From the results of whirl fire for methanol and n-Heptane, mass loss rate and air entrainment rate of n-Heptane was found to faster 1.33 to 1.58 times and 4.38 to 5.44 times compared with methanol, respectively. Consequently, mass loss rate and air entrainment rate in whirl fire was able to identified decrease as height of fire source increases and the higher the heating value, increases the that's value.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.49-55
• /
• 2023

Currently, the demand for green technologies toward a sustainable future is rapidly increasing due to growing concern over environmental issues. Methanol is biodegradable and can provide clean combustion to reduce sulfur oxide and nitrogen oxide emissions, and therefore it is a candidate fuel for marine engines. However, the effect of methanol on tribological characteristic degradation should be addressed for methanol-fueled engines. In this study, the methanol addition effects on tribological characteristic degradation is experimentally assessed using a pin-on-disk tribo-tester. Ni-based alloy is used as a target material due to its broad applicability as an engine component material. For a lubricant, engine oil with and without methanol are used. The tests are conducted for up to 10,000 cycles under boundary lubrication while the change in friction force is monitored. Additionally, the wear rate is determined based on laser scanning confocal microscope data. An additional test in which methanol is added at regular intervals is performed with an aim to directly observe its effect on friction. Overall, the friction coefficient increases slightly with increasing methanol concentration. Furthermore, the wear rate of the pin and disk increase significantly with methanol addition. The results also indicate that the friction increases instantaneously with methanol addition at the contacting interface. These findings may be useful for better understanding the methanol effect on the tribological characteristics of Ni-based alloys for methanol-fueled engines with improved performance.

• Korean Journal of Food Science and Technology
• /
• v.36 no.3
• /
• pp.518-521
• /
• 2004

Ginseng saponin was isolated from panax ginseng root using high-speed countercurrent chromatography (HSCCC). Preliminary studies were performed to optimize physical properties of two-phase solvent system and operating parameters including rotation speed of column, elution mode of mobile phase, and flow rate. Two-phase solvent system for isolation of ginseng saponins was composed of chloroform, water, and methanol as blending solvent. Chloroform-aqueous methanol (4:6) systems with various concentration of methanol in water were evaluated for retention of stationary phase in column. Retention of stationary phase decreased with increasing flow rate in tail-to-head elution mode using upper phase as mobile phase and head-to-tail elution mode using lower phase as mobile phase. Latter mode produced high retention at flow rate of 5 mL/min. Optimum conditions for isolation of saponin were chloroform/methanol/water (40/39/21) solvent system; mobile phase, of lower organic layer, flow rate, of 5 mL/min, head to tail elution mode, rotation speed, of 800 rpm, and sample injection, of $200{\mu}L$, Recovery yield of ginseng saponin from panax ginseng root extract by HSCCC was 63.6%, and the purity of HSCCC fractions was verified by TLC.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.3
• /
• pp.292-298
• /
• 2011

This study examines the effects of the ambient temperature (AT), methanol feeding temperature (MFT), methanol concentration (MC) and methanol flow rate (MFR) on the performance and cell temperature (CT) of a 5-stacked direct methanol fuel cell (DMFC). The AT, MFT, MC, and MFR are varied from $-10^{\circ}C$ to $+40^{\circ}C$, $50^{\circ}C$ to $90^{\circ}C$, 0.5M to 3.0M and 11.7 mL $min^{-1}$ to 46.8 mL $min^{-1}$, respectively. The performance of the DMFC under various operating conditions is analyzed from the I-V polarization curve, and the methanol crossover is estimated by gas chromatography (GC). The performance of the DMFC improves significantly with increasing AT. The open circuit voltage (OCV) decreases with increasing MC due to the enhanced likelihood of methanol crossover. The cell performance is improved significantly when the MFR is increased from 11.7 mL $min^{-1}$ to 28.08 mL $min^{-1}$. The change in cell performance is marginal with further increases in MFR. The CT increases significantly with increasing AT. The effect of the MFT and MFR is moderate, and the effect of MC is marginal on the CT of the DMFC.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.2
• /
• pp.123-128
• /
• 2011

It has been stand high in estimation to converse from Carbon dioxide to Dimethyl Ether in new alternative fuel energy division in 21C, especially Using of DME in point of view of transportation fuel has been discussed of a new clean energy which is very lower of exhaust gas than gasoline and diesel energy. In this paper it is used ZSM-5 and I developed new catalyst by addition of cerium to control acidity. The new catalyst was proved high conversion rate, when it was conversed from methanol to DME, there wasn't any additional material except DME and water, and I overlooked reaction temperature, reaction time, amount of catalyst, amount of added cerium, effect of water content in methanol, reaction temperature by making change of reaction time. I have conclude that conversion rate to DME was increased as increased of catalyst amounts. The best catalyst condition of without additional product was treated poisoning from ZSM-5 to 5% cerium and new catalyst was not effected in purity of fuel methanol.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.261-269
• /
• 2015

In this study, numerical analysis of curved channel steam-methanol reformer was conducted using the computational fluid dynamics (CFD) commercial code STAR-CCM. A pre-numerical analysis of reference model with a cylindrical channel reactor was performed to validate the combustion model of the CFD commercial code. The result of advance validation was in agreement with reference model over 95%. After completing the validation, a curved channel reactor was designed to determine the effects of shape and length of flow path on methanol conversion efficiency and generation of hydrogen. Numerical analysis of the curved-channel reformer was conducted under various flow rate ($10/15/20{\mu}l/min$). As a result, the characteristics of flow and mass transfer were confirmed in the cylindrical channel and curved channel reactor, and useful information about methanol conversion efficiency and hydrogen generation was obtained for various flow rate.

• Journal of Environmental Health Sciences
• /
• v.37 no.2
• /
• pp.133-140
• /
• 2011

Antimicrobial activity and bactericidal activity of Caesalpinia sappan L. extracts were investigated against five food-borne pathogens, E. coli, S. aureus, S. typhimurium, B. cereus and L. monocytogenes. Methanol extract of Caesalpinia sappan L. revealed antimicrobial activities against five pathogens. In particular, by paper disc diffusion the highest activity was shown against L. monocytogenes. Antimicrobial activities of methanol extracts showed the most potent activities, but hexane fraction had no activity. Fractions of ethyl acetate and butanol turned out to have higher antimicrobial activities against Gram(+) bacteria than Gram(-) bacteria. The minimum inhibitory concentration against five food-borne pathogens was 1.563 mg/ml on Gram(+) bacteria and 3.125 mg/ml on Gram(-) bacteria. The result of antimicrobial activity in a shaking flask method showed that bacterial growth rate fell by more than 99.999% at 3.125 mg/ml of methanol extract. The highest rate of viable reduction (99.998%) was shown at 0.781 mg/ml of methanol extract against L. monocytogenes. After five minutes of reaction between test strains and methanol extracts, the growth rates of five kinds of bacteria were reduced by more than 99.999% at a concentration of 100 mg/ml. Therefore, it is suggested that methanol extracts of Caesalpinia sappan L. can be developed as a natural sanitizer or disinfectant.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.127-128
• /
• 2006

Nafion/basic polymer composite membranes were prepared to reduce the methanol crossover for the application of direct methanol fuel cell. The thermal and mechanical properties increased with increasing basic polymer contents due to the formation of complex via acid/basic interaction. The water uptake, proton conductivity, methanol permeability decreased with increasing basic polymer concentration by reduction of acidity associated with the formation of acid/base complex. The molecular effect on those properties was not considerable.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.333-335
• /
• 2001

A simple control strategy of DO-stat was introduced to the recombinant rGuamerin production process in Pichia pastoris. This induction strategy consisted of two interrelated control loops ‘by which oxygen ratio of inlet gas and methanol feeding rate was controlled. Using this control strategy, over-feeding or under-feeding of methanol could be avoided in concomitance with the efficient control of dissolved oxygen level. As a result, the cell concentration reached 130 g/L and rGuamerin expression level was 450 iu/L, which was more than 40% increased result comparing with the fed-batch process using manual control of methanol feeding rate.