• 한국정밀공학회지
• /
• 제20권2호
• /
• pp.129-135
• /
• 2003

The fatigue life of a structure can be enhanced by improving the mechanical and metallurgical aspects to strengthen the material around regions of high stress. Coldworking of holes in structures is one of the mechanical methods of strengthening material. The material for this research is A12024-T351 which is used for the primary member or aircraft. Specimens were tested under constant amplitude loading and residual stresses measured by X-ray diffraction technique. Fatigue crack initiation life was evaluated by a strain-life equation which was considered initial residual stress and residual stress relaxation exponent as a function of the strain amplitude. The predictions on fatigue crack initiation life were compared with experimental results. A wide range of discrepancies between them was found.

• 한국재료학회지
• /
• 제13권9호
• /
• pp.625-630
• /
• 2003

Increasing environmental concerns require to solve the problem produced due to the use of heavy metals in coating formulations. Therefore, it is necessary to develop new coating strategy employing inherently conducting polymers such as Polyaniline(PANI). Polyaniline films were electrosynthesized by oxidation of aniline on cold rolled and weathering sheets using the potentiostatic mode from an aqueous oxalic acid medium. Potentiodynamic polarization curves were obtained for cold rolled and weathering sheets in the aqueous solution of 3% sodium chloride. The structure and properties of polyaniline film were elucidated using SEM, DSC, SST. A high corrosion resistance of polyaniline films were observed with a gain of the corrosion potential around 600-900 mV positive in the substrate covered with polyaniline than in the case without it.

• 한국표면공학회지
• /
• 제51권1호
• /
• pp.11-20
• /
• 2018

Hydrophobic and Superhydrophobic surfaces are promising technology for the surface finishing of metallic materials due to its water-repellency. Realization of highly water-repellent surface on aluminum and its alloys provides various functionalities for real application fields. In order to realize the hydrophobic/superhydrophobic surfaces on aluminum and its alloys, various technologies have been demonstrated. Especially, traditional anodic oxidation for aluminum has been widely employed for the morphological texturing of surfaces, which is essential to enhance the hydrophobic efficiency. De-wetting superhydrophobic surface on aluminum provides various exceptional properties, such as anti-corrosion, anti-/de-icing, anti-biofouling, drag reduction, self-cleaning and liquid separation. Nevertheless, the durability and stability of superhydrophobic surfaces still remain challenges for their actual applications in engineering systems and industry. In this review, the theoretical/experimental studies and current technical limitations on the hydrophobic and superhydrophobic surface using anodic oxidation of aluminum have been summarized.

• Applied Microscopy
• /
• 제26권4호
• /
• pp.479-487
• /
• 1996

Thin epilayer structures of GaAs/AlAs/InGaAs, grown by Molecular Beam Epitaxy, were investigated by high resolution transmission electron microscopy, Image in the [110] zone axis was taken and compared with the calculated images. The supercell structure which contains GaAs, AlAs and InGaAs layers was designed and was employed in the image calculation with MacTempas computer program. Good agreement was shown between experimental image and a set of calculated images with varying defocus and sample thickness.

• 한국표면공학회지
• /
• 제37권4호
• /
• pp.191-195
• /
• 2004

Gallium or sulphur additions in $CuInSe_2$ were prepared using RF magnetron sputtering and pulsed laser deposition respectively. All of the observed thin films shows a chalcopyrite structure with the S and Ga addition increases the favourable (112) peak. The optical absorption coefficients were slightly decreased. The energy band gap of films could be shifted from 1.04 to 1.68 eV by adjusting the mole ratio of S/(S+Se) and Ga/(In+Ga). It is possible to obtain the optimum energy band gap by adding S or Ga solute at a certain ratio in favour of Se and In respectively. It is also necessary to control the ratio of Ga and S additions and to retain a certain portion of In and Se to provide better properties of thin films.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1557-1559
• /
• 2000

In this paper, we intend to establish the judgement of electrical fire through analysis of PT(Potential Transformer) using the power installation. The columnar structure and the void generated by abrupt heat grew at the tenter of boundary-face on the metallurgical microscope analysis. The detection of OK lines was confirmed by EDX(Energy Dispersive X-ray spectroscopy) as melting and recombination due to the layer-short of the wiring. We found that the thermal-weight decrease occurred at 300$^{\circ}C$ in case of being the thermal-deterioration on the base of the result that analyzed the insulated-materials by using TGA, and the thermal reaction limited-value of PT insulator was about 300$^{\circ}C$ on the DSC curve. As this analysis, we confirmed what the layer-short appeared in the wiring of PT.

• Journal of Magnetics
• /
• 제7권1호
• /
• pp.14-17
• /
• 2002

Magnetic multilayers of a ferromagnetic (FM)/insulator (I)/ferromagnetic (FM) structure have been studied to investigate magnetic exchange coupling between two FM layers. As the Mumetal $(Ni_{77}Fe_{14}Mo_{5}Cu_4$ wt%) growth temperature increases, the grain size and the surface roughness increase simultaneously. The smallest coupling field is obtained at $40^\circ{C}$ where the grain size is larger than that of the $20^\circ{C}$ sample. The exchange coupling field increases again at temperatures higher than $40^\circ{C}$ due to increase in the surface roughness of the Mumetal.

• 한국주조공학회지
• /
• 제39권5호
• /
• pp.94-101
• /
• 2019

This study investigated the microstructure properties of A356 and AC8A alloys with a rheocasting mold using an inclined cooling plate. In addition, a formability evaluation was performed according to the solid fraction. Regardless of the position, the overall microstructure was shown to be uniform and a finer crystal structure was obtained as the solid fraction increased. The study confirmed that the molding pattern changed according to the solid fraction and that the spherical α-Al and eutectic α were identified. The results of the formability according to the solid fraction of A356 and AC8A alloys were similar to the simulation results.

• 소성∙가공
• /
• 제12권5호
• /
• pp.457-464
• /
• 2003

In the powder compact melting technique, proper precursor fabrication is very important because density distribution after foaming and foamability are determined during precursor fabrication process. The fabrication of the precursor has to be performed very carefully because any residual porosity or other defects will lead to poor results in further processing. In order to evaluate the effect of the compaction parameters on the kinetics of the foaming process, a series of experiments were performed. In this study, aluminium foams with a closed cell structure were fabricated by using both the powder compact method and the induction heating process. A proper induction coil was designed to obtain a uniform temperature distribution over the entire cross sectional area of precursor. To establish the foamable precursor fabrication conditions, effects of process parameters such as the titanium hydride content (0.3∼1.5 wt.%), pressing pressure of the foamable precursor (50∼150kN) on the pore morphology were investigated.

• Advances in materials Research
• /
• 제7권2호
• /
• pp.105-118
• /
• 2018

Magnesium and its alloys are attracted towards all engineering applications like automotive, marine, aerospace etc. due to its inherent high strength to weight ratio. But, extensive use of Mg alloys is limited to the current scenario because of low wear and corrosion resistance behavior. However, equal channel angular press is one of the severe plastic deformation technique which has been effective method to improve the wear and corrosion resistance by achieving fine grain structure. In this study, the effect of grain refinement on wear and corrosion resistance of AZ80 Mg alloys were investigated. The wear behavior of the coarse and fine-grained Mg alloys was examined through $L_9$ orthogonal array experiments in order to comprehend the wear behavior under varies control parameters. It was shown that ECAPed alloy increased the wear and corrosion resistance of the Mg alloy through the formation of fine grain and uniform distribution of secondary ${\beta}-phase$. Also, the performance of AZ80 Mg alloy for these changeswas discussed through SEM morphology.