• 한국구조물진단유지관리공학회 논문집
• /
• 제22권4호
• /
• pp.68-75
• /
• 2018

기존의 정수처리 방법으로는 제거되지 않는 물질이 발생함에 고도정수 처리 시설의 도입이 증가하고 있다. 그러나 오존을 이용한 고도정수처리 시설의 내부 방수 방식재는 오존의 산화력에 의해 열화되며 콘크리트까지 영향을 미쳐 내구성 저하의 원인이 된다. 본 연구에서는 내오존성 및 내화학성이 뛰어난 금속 패널을 기존의 시공법 보다 손쉬운 방법으로 시공하기 위한 방법으로 금속용사 공법을 이용하여 수처리 시설 콘크리트 구조물의 열화를 원천적으로 방지하기 위한 마감공법 개발 연구의 일원으로 용사금속 종류 및 피막의 표면처리 방법에 따른 내오존성 평가를 실시하였으며, 오존처리 후의 부착강도를 평가하였다. 실험결과 용사금속 Ti이 용사 후에도 내오존성이 뛰어난 것으로 나타났으며 표면처리 방법으로는 테프론계 봉공처리제를 사용하여 마감하는 것이 내오존성 및 부착성능 확보에 가장 적합한 방법이라 판단된다.

• 대한치과기공학회지
• /
• 제17권1호
• /
• pp.5-9
• /
• 1995

This study was carried out by obsorving to the conditions of an oxide on the surface of alloy according to the conditions of its heat treatment and analysing the change in composition on its surface. The result of this study is summarized as fellows. 1. It was shown that the higher the more the generated metal oxide while the higher the temperature of heat treatment. 2. The metal oxide was manily composed of Ni and Cr oxides. 3. The Ni composition indicated reduction while the higher the heat treatment in vaccum condition. 4. The Cr composition indicated increase while the higher the heat treatment in vaccum condition.

• Carbon letters
• /
• 제7권1호
• /
• pp.34-41
• /
• 2006

The objective of this paper is to compare the variation of surface properties by hydrochloric acid pre-treatment and of metallic potassium and their salts loading effect for activated carbon after surfaces transformation by acid. From the results of nitrogen adsorption, each isotherm shows a distinct knee band, which is closely related to the characteristic of microporous carbons with capillary condensation in micropores. In order to present the causes of the differences in surface properties and $S_{BET}$ after the samples were treated with hydrochloric acid, pore structure and surface morphology are investigated by adsorption analysis. X-ray diffraction (XRD) patterns indicate that activated carbons show better performance for metallic potassium and potassium salts by pre-treatment with hydrochloric acid. Scanning electron microscopy (SEM) pictures of potassium/activated carbon particles provide information about the homogeneous distribution of metal or metal complex on the surface. For the chemical composition microanalysis for potassium treatment of the activated carbon pre-treated with hydrochloric acid, samples were analyzed by energy disperse X-ray (EDX). Finally, the type and quality of oxygen groups are determined from the method proposed by Boehm. A positive influence of the acidic groups on the carbon surface by acid treatment is also demonstrated by an increase in the contents of potassium salts with increasing of acidic groups calculated from Boehm titration.

• 대한치과기공학회지
• /
• 제38권3호
• /
• pp.175-183
• /
• 2016

Purpose: Observation of Oxide Film Formation and Bonding Strength according to surface treatment of Co-Cr Alloy for porcelain fused to Metal. Methods: metal specimens $0.5mm{\times}25mm{\times}4mm$ in size were made using Co-Cr alloys for porcelain fused to metal crown (Heraenium P, Tae jung Medis). Dental porcelain $0.5mm{\times}25mm{\times}4mm$ in size was sintered on the metal specimens after changing the etching time, sandblasting condition, and heat treatment temperature. Subsequently, the bonding strength was compared by the three-point flexural strength test using a universal testing machine (UTM) to observe the fracture surface and oxidized layers. Results: With regard to the experimental group treated with acid-etching, Specimen 1 treated for 25 minutes (B-3) showed the highest bonding strength, and Specimen 2 treated only with sandblasting showed the most excellent bonding force at 3.5 bar (C-3). With regard to the experimental group treated with sandblasting at 3.5 bar after acid-etching for 25 minutes, Specimen 3 with heat treatment at $980^{\circ}C$ (D-3) showed the highest bonding strength. Conclusion: The specimen which went through both sandblasting and etching, showed an excellent ceramicmetal bond strength.

• 한국재료학회지
• /
• 제32권10호
• /
• pp.414-418
• /
• 2022

Magnesium alloy is the lightest practical metal. It has excellent specific strength and recyclability as well as abundant reserves, and is expected to be a next-generation structural metal material following aluminum alloy. This paper investigated the possibility of thin plate fabrication by applying a overheating treatment to the melt drag method, and investigating the surface shape of the thin plate, grain size, grain size distribution, and Vickers hardness. When the overheating treatment was applied to magnesium alloy, the grains were refined, so it is expected that further refinement of grains can be realized if the overheating treatment is applied to the melt drag method. By applying overheating treatment, it was possible to fabricate a thin plate of magnesium alloy using the melt drag method, and a microstructure with a minimum grain size of around 12 ㎛ was obtained. As the overheating treatment temperature increased, void defects increased on the roll surface of the thin plate, and holding time had no effect on the surface shape of the thin plate. The fabricated thin plate showed uniform grain size distribution. When the holding times were 0 and 30 min, the grain size was refined, and the effect of the holding time became smaller as the overheating treatment temperature increased. As the overheating temperature becomes higher, the grain size becomes finer, and the finer the grain size is, the higher the Vickers hardness.

• 한국표면공학회지
• /
• 제37권5호
• /
• pp.289-295
• /
• 2004

A dense palladium-nikel (Pd-Ni) alloy composite membrane has been fabricated on microporous nickel support mixed with submicron/micron nickel powder instead of mesoporous stainless steel support. Plasma treatment process is introduced as pre-treatment process instead of HCI activation. Pd-Ni alloy composite membrane prepared by electro plating was fairly a uniform and dense surface morphology. The membrane was characterized by permeation experiments with hydrogen and nitrogen gases at temperature 773 K and pressure 2.2 psi. The results showed that hydrogen ($H_2$) permeance was 27 ml/$\textrm{cm}^2$ㆍatmㆍmin and hydrogen/ nitrogen ($_H2$$N_2$) selectivity was 8 at 773 K.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.71-74
• /
• 2000

In this study, the optimal condition of surface treatment for aluminum panel was determined by measuring the contact angle and T-peel strength. The contact angle was measured for various mixture ratios of acetylene gas and nitrogen gas. The mixture (acetylene gas to nitrogen gas) ratios used were 1:9, 3:7, 5:5, 7:3, and 9:1. The contact angle was also measured as a function of time of surface treatment. The results showed that the contact angle was a minimum for mixture ratio of 5:5. T-peel strength was a maximum for the treatment time of 30 second.

• Bulletin of the Korean Chemical Society
• /
• 제25권8호
• /
• pp.1189-1194
• /
• 2004

The adsorption isotherms of N2 onto the metallic silver treated activated carbon fiber samples after acid treatment are Type I with a small amount of capillary condensation hysteresis. Increasing amount of acid treatment leads to a decrease in SBETs and external surface area. But, micropore volume and average pore diameter are presented in constant regular values with increasing amount of sulfuric acid treatment. SEM observes the surface morphology and crystal grown state of metal on the fiber surface. The results of EDX of Ag-activated carbon fiber pre-treated with acid show the spectra corresponding to almost all samples rich in silver with increasing the amount of acid treated. The FT-IR spectra of Ag-activated carbon fiber show that the acid pre-treatment is consequently associated with the homogeneous dispersion of metal with the increased surface acidity of the activated carbon fiber. The type and quality of oxygen groups are determined with Boehm titration method. From the those results, a positive influence of the acidic groups on the carbon fiber surface by acid treatment is also demonstrated by an increase in the contents of metallic silver with increasing of acidic groups.

• 한국건축시공학회지
• /
• 제16권2호
• /
• pp.107-115
• /
• 2016

본 연구에서는 금속용사 시스템을 수처리 시설 콘크리트 구조물의 방수/방식 공법으로 사용하기 위하여 콘크리트 표면처리 방법에 따른 기초적 성능 평가 실험을 진행하였다. 실험결과 Sa-P-R-(S)(샌딩-침투성표면강화제-조면형성제-봉공처리)의 경우가 3.57MPa로 가장 높은 부착성능을 나타냈다. 부착성능이 확보된 면처리 방법을 기반으로 투수성, 투기계수 측정실험을 진행하였다. 실험 결과 Sa-P-R-(S)의 경우가 각각 $0.68{\times}10^{-8}cm/sec$, $0.45{\times}10^{-16}m^2$로 가장 우수한 성능을 나타내었다. 또한 SEM분석 결과 침투성 표면강화제를 도포한 실험체가 그렇지 않은 경우에 비해 콘크리트의 미세 구조가 더 치밀한 것을 확인 할 수 있었으며, 이러한 구조로 인해 침투제를 도포한 경우의 실험체에서 가장 높은 부착성능이 나타난 것으로 판단된다. 따라서 콘크리트의 표면 처리 방법은 금속용사 시스템을 적용하는데 있어, 매우 중요한 영향을 미치는 것으로 판단되며, 본 연구를 통하여 Sa-P-R-(S)의 경우가 수처리 시설 콘크리트 구조물의 적용하기에는 가장 적합한 면처리 방법이라 판단된다.

• 열처리공학회지
• /
• 제15권5호
• /
• pp.234-237
• /
• 2002