• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.3261-3266
• /
• 2012

Sodium borohydride($NaBH_4$) known as the material of hydrogen generation and storage can produce the hydrogen via catalytic hydrolysis. This protide chemical could be used in the hydrogen supply system for residential and mobile fuel cells, and thus many researches and developments regarding to these chemicals and decomposition reactions have been implemented. We experimented the hydrolysis of $NaBH_4$ alkaline solution by metal oxide-supported PGM(platinum group metal) catalysts and measured the generation rate of hydrogen which is product of decomposition reaction. We compared oxides as catalyst supports, and the precious metals, Pt and Ru for the catalysts and studied the effects of amounts of catalyst added and $NaBH_4$ concentrations on the hydrogen generation rates and patterns.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.163-169
• /
• 2020

Synthesis of Fe-Co/meso-HZSM5 catalyst, intended to be applied in Fischer-Tropsch (FT) reaction was investigated. The study emphasized the effect of desilication agents, NaOH and KOH, on the catalyst materials properties. Impregnation composition of active metal (Fe and Co) was also examined. HZSM-5, converted from ammonium ZSM-5 through calcination, was treated with NaOH and KOH for desilication, followed by impregnation with 10% metal loading. Fe composition in the initial mixture was varied at 10-50% from total composition. After impregnation, reduction was applied by flowing hydrogen gas at 400 ℃ for 10 hours. The use of KOH solution induced greater mesoporous volumes; however, it had a detrimental effect on zeolite crystal structure. NaOH solutions, on the other hand, increased mesopore area as high as 100%, indicated from surface area increase from 266.28 m²/g of HZSM-5, to 526.03 m²/g of NaOH-desilicated HZSM-5. In addition, the application of NaOH solution increased pore volume from 0.14 cc/g to 0.486 cc/g. Further, more Fe-Co alloys and less oxide of iron (Fe₂O₃) as well cobalt (Co₃O₄) had been commonly observed in the produced catalysts. The largest Fe-Co alloys could be found in 50Fe-50Co/HZSM-5

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.4
• /
• pp.368-375
• /
• 2006

Single and complex metal oxide catalysts supported onto a commercial DT51D $TiO_2$ have been investigated for gas-phase TCE oxidation in a continuous flow type fixed-bed reaction system to develop a better design approach to catalysts for this reaction. Among the $TiO_2$-supported single metal oxides used, i.e., $CrO_x,\;FeO_x,\;MnO_x,\;LaO_x,\;CoO_x,\;NiO_x,\;CeO_x\;and\;CuO_x$, with the respective metal contents of 5 wt.%, the $CrO_x/TiO_2$ catalyst was shown to be most active for the oxidative TCE decomposition, depending significantly on amounts of $CrO_x\;on\;TiO_2$. The use of high $CrO_x$ loadings greater than 10 wt.% caused lower activity in the catalytic TCE oxidation, which is probably due to production of $Cr_2O_3$ crystallites on the surface of $TiO_2$. $CrO_x/TiO_2$-supported $CrO_x$-based bimetallic oxide catalysts were of particular interest in removal efficiency for this TCE oxidation reaction at reaction temperatures above $200^{\circ}C$, compared to that obtained with $CrO_x$-free complex metal oxides and a 10 wt.% $CrO_x/TiO_2$ catalyst. Catalytic activity of 5 wt.% $CrO_x-5$ wt.% $LaO_x$ in the removal reaction was similar to or slightly higher than that acquired for the $CrO_x$-only catalyst. Similar observation was revealed for 5 wt.% $CrO_x$-based bimetallic oxides consisting of either 5 wt.% $MnO_x,\;CoO_x,\;NiO_x\;or\;FeO_x$. These results represent that such $CrO_x$-based bimetallic systems for the catalytic TCE oxidation on significantly minimize the usage of $CrO_x$ that is well known to be one of very toxic heavy metals, and offer a very useful technique to design new type catalysts for reducing chlorinated volatile organic substances.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.394-399
• /
• 2015

In this study, the Cu catalyst decorated with activated carbon fibers were prepared for improving $SO_2$ adsorption properties. Flame retardant and heat treatments of Lyocell fibers were carried out to obtain carbon fibers with high yield. The prepared carbon fibers were activated by KOH solution for the high specific surface area and controlled pore size to improve $SO_2$ adsorption properties. Copper nitrate was also used to introduce the Cu catalyst on the activated carbon fibers (ACFs), which can induce various reactions in the process; i) copper nitrate promotes the decomposition reaction of oxygen group on the carbon fiber and ii) oxygen radical is generated by the decomposition of copper oxide and nitrates to promote the activation reaction of carbon fibers. As a result, the micro and meso pores were formed and Cu catalysts evenly distributed on ACFs. By Cu-impregnation process, both the specific surface area and micropore volume of carbon fibers increased over 10% compared to those of ACFs only. Also, this resulted in an increase in $SO_2$ adsorption capacity over 149% than that of using the raw ACF. The improvement in $SO_2$ adsorption properties may be originated from the synergy effect of two properties; (i) the physical adsorption from micro, meso and specific surface area due to the transition metal catalyst effect appeared during Cu-impregnation process and ii) the chemical adsorption of $SO_2$ gas promoted by the Cu catalyst on ACFs.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.339-343
• /
• 2010

A series of $Ce_1Mg_xZr_{1-x}O_2$ (CMZO) mixed metal oxide with different molar ratio were prepared by simple co-precipitation method. The prepared materials were tested for their catalytic activity performance using Knoevenagel condensation of various aromatic aldehydes with barbituric acid under solvent-free condition in microwave. The best catalytic activity was obtained with CMZO (1:0.6:0.4). The synthesized materials were characterized by using XRD, FT-IR, SEM-EDS techniques.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.243-248
• /
• 2010

The emergence of different and disparate materials together with the convergence of both the 'old' and 'emerging' technologies is paving the way for integration of heterogeneous technologies that are likely to extend the limitations of silicon technology beyond the roadmap envisaged for complementary metal-oxide semiconductor. Formulation of new information processing concepts based on novel aspects of nano-scale based materials is the catalyst for new nanoarchitectures driven by a different perspective in realization of novel logic devices. The memory technology has been the pace setter for silicon scaling and thus far has pave the way for new architectures. This paper provides an overview of the inevitability of heterogeneous integration of technologies that are in their infancy through initiatives of material physicists, computational chemists, and bioengineers and explores the options in the spectrum of novel non-volatile memory technologies considered as forerunner of new logic devices.

• Journal of Sensor Science and Technology
• /
• v.16 no.4
• /
• pp.313-318
• /
• 2007

Single-wall carbon nanotube field-effect transistors (SWCNT FETs) of top gate structure were fabricated in a conventional metal-oxide-semiconductor field effect transistor (MOSFET) with gate electrodes above the conduction channel separated from the channel by a thin $SiO_{2}$ layer. The carbon nanotubes (CNTs) directly grown using thin Fe film as catalyst by thermal chemical vapor deposition (CVD). These top gate devices exhibit good electrical characteristics, including steep subthreshold slope and high conductance at low gate voltages. Our experiments show that CNTFETs may be competitive with Si MOSFET for future nanoelectronic applications.

• Ceramist
• /
• v.21 no.2
• /
• pp.38-48
• /
• 2018

This paper reports a comprehensive review of the state-of-the-art in research on the enhancement of sensing properties for the detection of gases in exhaled breath. Daily health monitoring and early diagnosis of specific diseases via the analysis of exhaled breath is possible. Because biomarkers in exhaled breath are emitted in a very small amount, it is necessary to develop highly sensitive gas sensors. In recent years, a number of researches have been carried out using various strategies for the enhancement of sensing properties such as doping, catalyst, hollow sphere, heterojunction, size effect. We introduced each strategy and summarized recent progress on sensing properties for detection of biomarkers in exhaled breath.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.367-369
• /
• 2011

본 연구에서는 글리세롤과 우레아를 이용하여 글리세롤카보네이트를 합성하는 반응을 진행하였다. ZnO와 Zn-Al 이원계 금속 산화물 촉매를 제조하고, 제조되어진 촉매를 사용하여 글리세롤의 전환율과 글리세롤카보네이트의 수율을 확인하였고, Al의 첨가에 따른 촉매 특성의 분석과 글리세롤카보네이트 합성반응에서의 역할에 대해 확인하였다. 글리세롤카보네이트 합성 반응에서 ZnO를 단독으로 촉매를 사용한 경우보다 Zn-Al 혼합 산화물을 촉매로 사용하여 반응하였을 때, 부반응이 억제되어 전환율 및 수율이 증가함을 확인하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.11-17
• /
• 2022

Direct exposure to toxic and hazardous gases has always been considered as the most pervasive problem worldwide, leading to a gradual increase in the number of asthma patients due to NO_x/SO_x gases inhaling and exposure to 50 ppm formaldehyde gases. Therefore, the development of accurate gas sensors is a key issue for resolving these problems. To address such issues, the development of membranes for selective filtering of target molecules as well as nanocatalyst for enhancing the sensing selectivity is highly crucial. In this review, the research progress for porous membrane materials (e.g. MOFs, and graphene) and nanocatalyst technology for the development of selective and accurate gas sensors will be discussed.