• Journal of Welding and Joining
• /
• 제12권3호
• /
• pp.48-55
• /
• 1994

In this experiment, to find optimum brazing conditions for Cu/Stainless Steel brazing using filler metals of Ag-Cu-Zn-Cd system, first of all spreading ratio was tested on 304 stainless Steel and low carbon steel. And then shear test of brazed joint was executed. As the result of that, the shear strengths of brazed joints were the range of 60-90 MPa. Through microstructure analysis for brazed interface layer, We found as follows. Firstly interface layer increased as time increased. Secondly continuous layer of Ag-Cd compound was observed along the side of stainless steel. Also by means of EDS analysis for fracture surface, ductile fracture was occurred and precipitates on the fracture surface were found to include Cr, Mn, Si in Ag-rich phase.

• 센서학회지
• /
• 제4권4호
• /
• pp.10-15
• /
• 1995

유기 박막 electoluminescent(EL) 소자를 제작하여 전극의 일함수에 따른 출력휘도의 의존성과 휘도-전압 특성을 측정하였다. 제작된 소자의 구조는 Indium-Tin-Oxide(ITO)/정공수송층/발광층(전자수송층)/금속전극이며, 정공수송층으로는 PMMA+TPD(0.5wt%)와 측쇄 액정 고분자 메트릭스인 MC homopolymer+TPD(0.005wt%)와 (MC/MMA)copolymer+TPD(0.005wt%)을 사용하였으며, 발광층은 $Alq_{3}$을, 금속전극으로는 Ca, Mg, Mg:Ag(10:1) 와 Al을 사용하였다. 출력특성이 전압에 따른 정류특성을 가짐을 보였으며, 소자의 문턱전압은 5볼트이고, 출력 휘도는 10 볼트에서 700 $Cd/m^{2}$이상의 휘도를 보였다.

• 대한치과보철학회지
• /
• 제27권1호
• /
• pp.143-179
• /
• 1989

To observe the bonding behavior of palladium-based alloys to porcelain; 1. Pd-Co binary alloy with the higher cobalt content, 2. Pd-Co binary alloy with the lower cobalt content, 3. Pd-Ag-Sn ternary alloy, 4. Pd-Ag binary alloy, 5. Pd-Cu-Au ternary alloy and 6. Pd-Cu binary alloy were made as 6 groups of experimental alloys. Each group of alloy was divided into 4 sub-groups such as one sub-group that was not degassed and three sub-groups that degassed for 5 minutes, 10 minutes and 15 minutes. On each specimen, weight changes after degassing, morphological changes of oxide layer by changing the degassing time, compositional changes at metal-ceramic interface and bond strength of metal-ceramic measured with planar shear test were observed and compared. The results of the present study allow the following conclusions to be drawn: 1. The alloy showing the greatest bond strength was Pd-Cu alloy without gold and bond strength was decreased by alloying gold to them. 2. Although Pd-Co alloy showed the most prominent oxidation behavior, bond strength of them to porcelain was not greatly high by the formation of porosities at metal-ceramic interfaces. 3. Likewise tin, cobalt formed the peaks on line profiles at metal-ceramic interface, however copper did not exhibit such peaks on line profiles. 4. Mainly, oxide layer on Pd-Co alloy was composed with cobalt, and for Pd-Co alloy with higher cobalt content the rise of bond strength was not significant by increased degassing time. 5. On Pd-Ag alloy not containing tin, during degassing for 15 minutes silver content was increased at metal-ceramic interface. 6. As an oxidized element, tin formed the oxide layers that widen their area by increasing the degassing time, while cobalt and copper showed the morphological changes of particle or crystal on oxide layer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.290-290
• /
• 2012

본 실험에서는 RF magnetron sputtering법과 evaporator법을 이용하여 다층박막 OMO구조를 $30{\times}30mm$ 유리기판 위에 제작하였다. Oxide층은 Sputter장비를 이용 IGZO막을 제작하였으며, Metal 층은 evaporator장비를 이용 Ag 막을 제작하였다. 변수로는 Oxide층의 시간에 따른 특성 변화를 연구하였다. 소결된 타겟으로는 In:Ga:ZnO를 각각 1:1:1 mol%의 조성비로 혼합하여 이용하였으며, Ag는 99.999%의 순도를 가진다. Oxide층의 RF sputter 공정 조건으로는 초기압력 $3.0{\times}10^{-6}$ Torr 이하로 하였으며, 증착 압력 $2.0{\times}10^{-2}$ Torr, Rf power 30 W, Ar gas 50 sccm으로 고정 시켰으며, 변수로는 5, 7, 9, 11분은 시간 차이를 두어 증착을 하였다. Metal층의 Evaporator 공정조건으로는 $5.0{\times}10^{-6}$ Torr이하, 전압은 0.3 V, Thickness moniter로 두께를 확인해가며 증착하였으며, $100{\AA}$으로 고정시켰다. 분석결과로는 XRD 측정 결과 35도 부근에서 Ag 피크가 관찰되었다. IGZO막 하나일때 90% 이상의 평균 투과율을 보였으며, 3층의 구조가 모두 증착됐을때의 투과도는 가시광영역에서 평균 80% 이상의 투과율을 보였으며, 500 nm부터 투과율이 떨어지기 시작해 800 nm부근에서는 평균 투과율이 30%까지 떨어져 Metal층인 Ag가 하나의 layer로 잘 증착이 된것을 보여주며, 플라즈몬효과를 보여줌을 알수있다. AFM측정 결과 평균 거칠기는 1.2 nm 정도의 거칠기를 확인했다. 홀 측정결과 전기적 특성은 발견되지 않았다.

• 한국전기전자재료학회논문지
• /
• 제31권6호
• /
• pp.408-411
• /
• 2018

We fabricated highly flexible Mn-doped $SnO_2$ (MTO)/Ag/MTO/polydimethylsiloxane (PDMS)/MTO multilayer transparent conducting films. To reduce refractive-index mismatching of the MTO/Ag/MTO/polyethylene terephthalate (PET), index-matching layers were inserted between the oxide-metal-oxide-structured films and the PET substrate. The PDMS layer was deposited by spin-coating after adjusting the mixing ratio of PDMS and hexane. We investigated the effects of the index-matching layer on the color and reflectance differences with different PDMS dilution ratios. As the dilution ratio increased from 1:100 to 1:130, the color difference increased slightly, while the reflectance difference decreased from 0.62 to 0.32. The MTO/Ag/MTO/PDMS/MTO film showed a transmittance of 87.18~87.68% at 550 nm. The highest value of the Haacke figure of merit was $47.54{\times}10^{-3}{\Omega}^{-1}$ for the dilution ratio of 1:130.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.362-365
• /
• 2001

The chalcogenide glasses of thin films have the superior property of photoinduced anisotrophy(PA). In this study, we observed the linear dichroism(D) using the irradiation with polarized He-Ne laser light, in the $Ag/As_{40}Ge_{10}Se_{15}S_{35}$ multi-layer. Mutilayer structures formed by alternating metal(Ag) a chalcogenide$(As_{40}Ge_{10}Se_{15}S_{35})$. Such multilayer structures have a greater sensitivity to illumination am larger dichroism in comparison the conventional double layer structure. Also new phenomena are discovered. These results will be show a capability of new method that suggested more improvement of photoinduced anisotropy property.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.362-365
• /
• 2001

The chalcogenide glasses of thin films have the superior property of photoinduced anisotrophy(PA). In this study, we observed the linear dichroism(D) using the irradiation with polarized He-Ne laser light, in the Ag/As$\sub$40/Ge$\sub$10/Se$\sub$15/S$\sub$35/ multi-layer. Mutilayer structures farmed by alternating metal(Ag) a chalcogenide(As$\sub$40/Ge$\sub$10/Se$\sub$15/S$\sub$35/). Such multilayer structures have a greater sensitivity to illumination and larger dichroism in comparison the conventional double layer structure. Also new phenomena are discovered. These results will be show a capability of new method that suggested more improvement of photoinduced anisotropy property.

• 한국전기전자재료학회논문지
• /
• 제28권3호
• /
• pp.185-190
• /
• 2015

In this study, we fabricated the indium gallium zinc oxide (IGZO), zinc oxide (ZnO), aluminum zinc oxide (AZO). oxide and silver are deposited by magnetron sputtering and thermal evaporator, respectively transparency and energy bandgap were changed by the thickness of silver layer. To fabricate metal oxide metal (OMO) structure, IGZO sputtered on a corning 1,737 glass substrate was used as bottom oxide material and then silver was evaporated on the IGZO layer, finally IGZO was sputtered on the silver layer we get the final OMO structure. The radio-frequency power of the target was fixed at 30 W. The chamber pressure was set to $6.0{\times}10^{-3}$ Torr, and the gas ratio of Ar was fixed at 25 sccm. The silver thickness are varied from 3 to 15 nm. The OMO thin films was analyzed using XRD. XRD shows broad peak which clearly indicates amorphous phase. ZnO, AZO, OMO show the peak [002] direction at $34^{\circ}$. This indicate that ZnO, AZO OMO structure show the crystalline peak. Average transmittance of visible region was over 75%, while that of infrared region was under 20%. Energy band gap of OMO layer was increased with increasing thickness of Ag layer. As a result total transmittance was decreased.

• 한국재료학회지
• /
• 제30권6호
• /
• pp.285-291
• /
• 2020

Recent advances in technology using ultra-thin noble metal film in oxide/metal/oxide structures have attracted attention because this material is a promising alternative to meet the needs of transparent conduction electrodes (TCE). AZO/Ag/AZO multilayer films are prepared by magnetron sputtering for Cu₂ZnSn(S,Se)₄ (CZTSSe) of kesterite solar cells. It is shown that the electrical and optical properties of the AZO/Ag/AZO multilayer films can be improved by the very low resistivity and surface plasmon effects due to the deposition of different thicknesses of Ag layer between oxide layers fixed at AZO 30 nm. The AZO/Ag/AZO multilayer films of Ag 15 nm show high mobility of 26.4 ㎠/Vs and low resistivity and sheet resistance of 3.58^⁎10^-5 Ωcm and 5.0 Ω/sq. Also, the AZO/Ag (15 nm)/AZO multilayer film shows relatively high transmittance of more than 65 % in the visible region. Through this, we fabricated CZTSSe thin film solar cells with 7.51 % efficiency by improving the short-circuit current density and fill factor to 27.7 mV/㎠ and 62 %, respectively.

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.134-146
• /
• 1995

Aluminium nitride(AlN) is currently under investigation as potential candidate for replacing alumium oxide(Al$_{2}$ $O_{3}$) as a substrate material for for electronic circuit packaging. Brazing of aluminium nitride(AlN) to Cu with Ag base active alloy containing Ti has been investigated in vacuum. Binary Ag$_{98}$ $Ti_{2}$(AT) and ternary At-1wt.%Al(ATA), AT-1wt.%Ni(ATN), AT-1wt.% Mn(ATM) alloys showed good wettability to AlN and led to the development of strong bond between brate alloy and AlN ceramic. The reaction between AlN and the melted brazing alloys resulted in the formation of continuous TiN layers at the AlN side iterface. This reaction layer was found to increase by increase by increasing brazing time and temperature for all filler metals. The bond strength, measured by 4-point bend test, was increased with bonding temperature and showed maximum value and then decreased with temperature. It might be concluded that optimum thickness of the reaction layer was existed for maximum bond strength. The joint brazed at 900.deg.C for 1800sec using binary AT alloy fractured at the maximum load of 35kgf which is the highest value measured in this work. The failure of this joint was initiated at the interface between AlN and TiN layer and then proceeded alternately through the interior of the reaction layer and AlN ceramic itself.