• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.79-83
• /
• 2014

Dye-sensitized solar cells (DSSCs) are applied in the emerging fields of building integrated photovoltaic and electronics integrated photovoltaic like small portable power sources as demands are increased with characteristic advantages. Highly flexible dye-sensitized solar cells (DSSCs) prepared on single stainless steel mesh were proposed in this paper. Single mesh DSSCs structure utilizing the spraying the chopped glass paper on the surface treated stainless steel mesh for integrating the space element and the electrode components, counter electrode component and photoelectrode component were coated on each side of the single mesh. The fabricated single mesh DSSCs showed the energy-conversion efficiency 0.50% which show highly bendable ability. The new single mesh DSSCs may have potential applications as highly bendable solar cells to overcome the limitations of TCO-based DSSCs.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.100-104
• /
• 2019

The 'ITO/Ag/ITO' multilayers as a highly conductive and transparent electrode, even with the optimum thickness conditions, the transmittances were much lower than those of a single ITO layer on some ranges of the visible wavelength. In order to improve the transmittance, Ag layer was formed with mesh structure. Where, the thickness of the Ag layer was about 10 nm and the space between the Ag lines was varied from 2.9 ㎛ to 19.6 ㎛ with the fixed Ag width of about 1.2 ㎛ in order to vary an open ratio of the Ag mesh structure. The transmittance and sheet resistance in the ITO/Mesh-Ag/ITO multilayer structure were analyzed depending on the open ratio. As a result, a trade off in the open ratio was necessary in order to obtain the transmittance as high as possible and the sheet resistance as possible low. By the open ratio of about 86%, in the ITO/Mesh-Ag/ITO multilayer structure, the transmittance was nearly same as the single ITO layer and the sheet resistance was about 62.3 Ω/.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.5
• /
• pp.58-64
• /
• 2000

This paper proposes a method for determining optimal EDM parameters based on discharge area from the physical model of a tool electrode. Main parameters, which affect the EDM performance, are peak value of currents, pulse-on time, and pulse-off time. Such parameters are closely dependent on the discharge area in EDM process. In this paper the discharge area is estimated from the CMM scanning data to the tool electrode. The method is very useful when any geometric information to the tool electrode is not provided from tool modeler or producer. The method consists of following four steps. First a triangulation mesh is constructed from the CMM data. Secondly, the z-map is modeled from the triangulated mesh. Thirdly, the discharge area is estimated from intersection between the z-map model and a z-height plane. Finally, the machining parameters are easily calculated by some known EDM equations to the discharge area. An example is introduced to show that the machining parameters are calculated from the CMM data to a tool electrode.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.2
• /
• pp.1-11
• /
• 2014

Flexible transparent conductive electrodes (TCEs) have recently attracted a great deal of attention owing to rapid advances in flexible electronic devices, such as flexible displays, flexible photovoltanics, and e-papers. As the performance and reliability of flexible electronics are critically affected by the quality of TCE films, it is imperative to develop TCE films with low resistivity and high transparency as well as high flexibility. Indium tin oxide (ITO) has been the most dominant transparent conducting material due to its high optical transparency and electrical conductivity. However, ITO is susceptible to cracking and delamination when it is bent or deformed. Therefore, various types of flexible TCEs, such as carbon nanotube, conducting polymers, graphene, metal mesh, Ag nanowires (NWs), and metal mesh have been extensively investigated. Among several options to replace ITO film, Ag NWs and metal mesh have been suggested as the promising candidate for flexible TCEs. In this paper, we focused on Ag NWs and metal mesh, and summarized the current development status of Ag NWs and metal mesh. The several critical issues such as high contact resistance and haze are discussed, and newly developed technologies to resolve these issues are also presented. In particular, the flexibility and durability of Ag NWs and metal mesh was compared with ITO electrode.

• Geomechanics and Engineering
• /
• v.39 no.1
• /
• pp.105-113
• /
• 2024

Recently, electrical resistivity surveys have been used to obtain information related to underground structures including burial structure type and depth. However, various field conditions hinder understanding measured electrical resistance, and thus there is a need to understand how various geometries affect electrical resistance. This study explores the effect of geometric parameters of a structure and electrodes on electrical resistance in the framework of the finite element method. First, an electrical resistance module is developed using the generalized mesh modeling technique, and the accuracy of the module is verified by comparing the results with the analytical solution for a cylindrical electrode with conical tip. Then, 387 cases of numerical analysis including geometric parameters of a buried structure and electrodes are conducted to quantitatively estimate the detection depth under a steady-state current condition. The results show that electrical resistance is increased as (1) shallower burial depth of structure, (2) closer distance between ground electrode and structure, (3) longer horizontal electrode distance. In addition, the maximum detection depth corresponding to converged electrical resistance is deeper as (4) closer distance between ground electrode and structure, (5) shorter horizontal electrode distance. The distribution of the electric potential around the electrodes and underground structure is analyzed to provide a better understanding of the measured electrical resistance. As engineering purpose, the empirical equation is proposed to calculate maximum detection depth as first approximation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.2023-2026
• /
• 2008

Cooling technologies using natural and forced convection are limited and operated in very low efficiency. The corona discharge is utilized as the driving mechanism for an ionic pump, which allows for air flow control and generation with low noise and no moving parts. These ideal characteristics of ionic pump give rise to variety applications. However, all of these applications would benefit from maximizing the flow velocities and efficiencies of the pumps. In this study a needle-mesh type ionic pump, with a ring type third electrode installed just near the needle point, has been investigated by focusing on elevating the ionic wind velocity and efficiency. As a result, the enhanced ionic wind velocity and increased power yield can be obtained with the proposed ionic pump with the third electrode.

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.117-121
• /
• 2018

A stainless steel mesh was applied to the cathode of an electro-Fenton system. Methylene blue (MB) solution was chosen as the model waste water with non-biodegradable pollutants. For the model waste water, the degradation efficiency was compared among various SUS mesh cathodes with different surface treatments and magnetite coatings on them. With increasing amount of the magnetite coating on SUS mesh, the degradation efficiency also increased. The improved electro-catalytic characteristic was explained by the increased amount of in situ generated hydrogen peroxide near the cathode surface. Cyclic voltammetry data also showed improved electro-catalytic performance for SUS mesh with more magnetite coatings on them.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.190-197
• /
• 2024

A commercial PbO₂ mesh cylinder electrode was utilized as the anode for the electrochemical degradation of the textile effluent after the biological treatment with the titanium cylinder as the cathode in a self-made tube electrolyzer. The electrochemical performances of the PbO₂ electrode in tube electrolyzer under different initial pH, electrolyte flow rates, current densities and times of the electrochemical degradation were investigated. The experimental results illustrated that the PbO₂ electrode can reduce the chemical oxygen demand (COD) of the textile effluent from 94.0 mg L^-1 to 65.0 mg L^-1 with the current efficiency of 88.3%, the energy consumption of 27.7 kWh kg^-1 (per kilogram of degraded COD) and the carbon emissions of 18.0 kg CO₂ kg^-1 (per kilogram of degraded COD) under the optimal operating conditions. In addition, the COD of the textile effluent could be reduced from 94.0 mg L^-1 to 22.0 mg L^-1 after the fifth electrochemical degradation. Therefore, PbO₂ mesh cylinder electrode in the tube cylinder was promising for the electrochemical degradation of the textile effluent.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1338-1347
• /
• 2018

In this study, Ti-mesh based electrodes were fabricated for the application of anode to the electrolysis process for wastewater treatment using Pd electroless plating method. The removal performance of the prepared Pd / Ti-mesh electrode was evaluated as representative dye RO16, and the durability and performance were maximized by varying the electrode manufacturing conditions. As a result, it was confirmed that the coating condition had no significant effect on the performance, and that the heat treatment process greatly affected the performance and the durability was improved. In addition, we tried to maximize performance and durability by complexing Ir, Ru, and Ta. However, as the thickness of the layer increased due to the limitation of the coating method, the resistance increased and the performance decreased accordingly.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.235-239
• /
• 2002

In this study mesh-type PECVD system was suggested to minimize the hydrogen concentration. The main structural difference between the triode system and a conventional system is that, a third electrode, a mesh, is inserted between the powered and the ground electrode. We investigated several conditions to compare with conventional PECVD. The main effect of mesh was to minimize the substrate damage by ion bombardment and to enhance the surface reaction to induce hydrogen desorption. It was also found that hydrogen concentration decreased but deposition rate increased as increasing applied bias. Applied DC-bia s enhanced sputtering process. Intense ion bombardment causes the weakly bonded hydrogen or hydrogen-containing species to leave the growing film and increased adatom mobility. Furthermore, addition of hydrogen gas enhance the surface diffusion of adatom.