• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.65-76
• /
• 1986

Carious dentin can be classified, on the basis of their clinical characteristics, into three groups; sound, sclerotic and active carious dentin. Active carious dentin differs from sclerotic dentin by its abscence of variable bacteria within tubles and amount of chemical content. But the apatite molecules of active carious dentin are not fully studied. The purpose of this study was to observed the physico-chemical characteristics of deep carious dentin. The samples of sound, sclerotic and active carious dentin were obtained respectively from 300 freshly extracted carious teeth. Bacterial-rich zone of superficial soft dentin layer was removed with hand instruments from all samples in advance. The samples were powdered and sieved (200 mesh) before analyses. Identification and estimation of the crystallinity of the samples were carried with X-ray diffraction and infrared absorption analyses. Measurements were made on a Rigaku Denki (Rigaku, geiger flex III, Japan) X-ray diffractometer with Cu-target at 30 Kv, 30 mA and are traced on a monochromatic tracer. Infrared absorption analysis was made on FT-IR spectrophometer (Nicolet Instrument Co.) using KBr pellets containing the samples and was recorded on data process (Model IR-80. Nicolet Instrument, Co). The following conclusions were as follows; 1. The nature of the main inorganic structure of sound, sclerotic and active carious dentin proved to be hydroxyapatite. 2. It was difficult to determine the identification due to their crystallinity of sound, sclerotic and active carious dentin. But sound dentin was the highest in crystallinity among them. 3. The magnesium whitlockite was to be found in active carious dentin, but not in sound and sclerotic dentin. 4. The carbonate content was highest in sound dentin, but the lowest was in active carious dentin.

• 대한화학회지
• /
• 제13권1호
• /
• pp.49-55
• /
• 1969

螢光X線을 利用하여 珪酸鹽鑛物中의 主成分인 $SiO_2$, $Al_2O_3$, $Fe_2O_3$, CaO, MgO 및 $K_2O$를 迅速히 分析할 目的으로 試料의 處理 測定 및 各條件에 對하여 檢討하였다. 試料를 Lithium Tetraborate로 용융하여 300Mesh 以上의 微粉末로 한後 40,000Lb의 壓力으로 成型하여 Tungsten과 Chromium 對陰極의 X-線管과 LiF, EDDT, ADP의 分光結晶을 使用하여 測定하였다. 各成分에 對한 檢量曲線은 Matrix Effect를 고려하여 N.B.S 및 International Rock Standard를 選定 使用하였고 Lanthanum Oxide 및 Binder로서 Borie Acid를 첨가하여 얻었다. 各成分에 對하여 本法의 再現性 및 誤差를 檢討하기를 爲하여 I.R.S T-1을 使用하여 測定한 結果 0.47($SiO_2$), 0.85($Al_2O_3$), 0.05($Fe_2O_3$), 0.07(caO), 0.02($K_2O$), 0.13(MgO)의 標準偏差를 얻었다. 또한 化學分析植에 對한 偏差를 求하고져 Clay, Kaoline, Alunite, Wallastonite 및 Zeolite 等의 珪酸鹽鑛物을 選定하여 化學分析 및 本法에 依한 分析結果를 비교하였다.

• 한국전산구조공학회논문집
• /
• 제27권1호
• /
• pp.17-26
• /
• 2014

본 논문은 MLS(Moving Least Squares) 차분법을 바탕으로 동적균열전파 해석을 수행하기 위한 알고리즘을 제시한다. MLS 차분법은 절점만으로 이루어진 수치모델을 사용하며, 이동최소제곱법을 이용하여 전개한 Taylor 다항식을 기초로 미분근사식을 유도하기 때문에, 요소망의 제약에서 완벽하게 벗어난 절점해석이 가능하다. 시간항을 포함하는 동적 평형방정식은 Newmark 방법으로 시간적분 하였다. 동적하중을 받는 균열이 전파할 때, 매 시간단계마다 절점모델을 재구성하지 않고 균열선단 주변에서 국부적인 수정을 통해 해석이 가능하다. 동적균열을 묘사하기 위해 가시한계법(visibility criterion)을 적용하였고, 동적 에너지해방률을 산정하여 균열의 진전유무와 그에 상응하는 진전방향을 결정하였다. 모드 I 상태와 혼합모드 상태에서 균열이 진전하는 현상을 모사하였고, 이론해와 Element-Free Galerkin법으로 계산한 결과와의 비교를 통해 개발된 알고리즘의 정확성과 안정성을 검증하였다.

• 대한소아치과학회지
• /
• 제25권1호
• /
• pp.76-92
• /
• 1998

The purpose of this study was to evaluate the possible efficacy of Nd-YAG laser as a dentin conditioner by observing the laser irradiation dentin surface under scanning electron micrograph and measuring shear bond strength of restored light-cured glass ionomer mold. Fifty intact premolars were prepared for shear bond strength tests. The teeth were randomly divided into five groups as follows; Group I. no treatment Group II. 10% poly acrylic acid, 20 sec Group III. laser treatment 2 w, 20 Hz, 2 sec Group IV. laser treatment 2 w, 20 Hz, 5 sec Group V. laser treatment 2 w, 20 Hz, 10 sec Samples of each group were restored with light-cured glass ionomer cement after dentin conditioning and then measuring the shear bond strength of each specimen were measured using universal testing machine. Additional ten premolars were prepared for SEM analysis The result from the this study can be summarized as follows. 1. Shear bond strength of polyacrylic acid-treated group (II) was significantly higher than other groups (p<0.05). 2. No statistically significant difference could be found between three laser-treated groups (III, IV, V) in shear bond strength(p>0.05) 3. According to the result of observation under SEM, Polyacrylic acid was shown to have removed the smear layer effectively and opened the dentinal tubules, whereas the laser has produced the irregular surface mainly composed of melted and fused structure. The microcracks found in laser-treated groups increased in number with irradiation time and formed the regular mesh-type in 10 sec-irradiation group. 4. The ultrastructural change of dentin surface created by laser irradiation was found to the improper for bonding of the glass ionomer restorative materials. And the lower shear bond strength of laser irradiated group might have been due to the failure to form the suit able dentin surface for the glass ionomer to penetrated into and form the proper micromechanical retention.

• 한국정보통신학회논문지
• /
• 제13권10호
• /
• pp.2097-2104
• /
• 2009

육상에서는 기지국을 통해 고속의 무선 통신 시스템을 사용하고 없는 반면, 해상의 경우 기지국을 설치하는데 제약이 따르고, 이로 인해 긴 전송거리를 갖는 저속의 MF/HF 대역 모뎀을 주로 사용 하고 있다. 고속 전송을 위해 해상위성통신이 사용되기도 하지만, 비용이 비싸다는 단점을 가지고 있다. 낮은 비용으로 전송속도를 증가시키기 위해서는 Vehicular Ad-hoc Network (VANET)과 같은 기지국이 없는 상황에서 단말간의 통신이 가능한 네트워크의 구성이 필요한데, 해상의 경우 육상과는 다른 환경적인 특징들을 갖기 때문에 본 논문에서는 해상에서의 Ad-hoc 네트워크를 Nautical Ad-hoc Network (NANET) 이라 칭하며 NANET을 위한 시나리오를 설정하고, 시나리오 별 Multiple Access 및 Duplex 방식을 분석한 후, NANET을 구축하기 위한 주요 후속 연구 주제들을 정리하여 해상 무선 통신 연구를 위한 기본적인 Guide Line을 제시한다.

• 한국표면공학회지
• /
• 제37권5호
• /
• pp.253-262
• /
• 2004

Calcareous deposits are the consequence of pH increase of the electrolyte adjacent to metal surface affected by cathodic current in seawater. It obviously has several advantages over conventional coatings, since the calcareous deposit coating is formed from coating (Mg$^{2+}$, $Ca^{2+}$) naturally existing in seawater. In consideration of this respect, environment friendly calcareous deposit films were formed by an electro deposition technique on steel substrates submerged in 48$^{\circ}C$ natural seawater. And the influence of current density, coating time and attachment of steel mesh on composition ratio, structure and morphology of the electrodeposited films were investigated by Scanning Electron Microscopy(SEM), Energy Dispersive Spectroscopy(EDS) and X-Ray Diffractor(XRD), respectively. Accordingly, this study provides a better understanding of the composition between the growth of $Mg(OH)_2$ and $CaCO_3$ during the formation of electro deposit films on steel substrate under cathodically electrodeposition in $48^{\circ}C$ natural seawater. The Mg compositions, in general, are getting decreased regardless of current density but Ca compositions are getting increased as electrodeposition time runs. That is, $Mg(OH)_2$ compounds of brucite structure shaped as flat type is formed at the initial stage of electrodeposition, but CaCO$_3$ compounds of aragonite structure shaped as flower type is formed in large scale. Besides, $Mg(OH)_2$ compounds were much formed at 5 A/$\m^2$ environment condition compared to the 3 A/$\m^2$ and 4 A/$\m^2$ environment conditions. This is because that OH- which was comparatively largely generated at the metal surface is preferably combined with $Mg^{2+}$TEX>.

• Geomechanics and Engineering
• /
• 제2권1호
• /
• pp.1-18
• /
• 2010

The analysis of structure response and design of buried structures subjected to dynamic destructive loads have been receiving increasing interest due to recent severe damage caused by strong earthquakes and terrorist attacks. For a comprehensive design of buried structures subjected to blast loads to be conducted, the whole system behaviour including simulation of the explosion, propagation of shock waves through the soil medium, the interaction of the soil with the buried structure and the structure response needs to be simulated in a single model. Such a model will enable more realistic simulation of the fundamental physical behaviour. This paper presents a complete model simulating the whole system using the finite element package ABAQUS/Explicit. The Arbitrary Lagrange Euler Coupling formulation is used to model the explosive charge and the soil region near the explosion to eliminate the distortion of the mesh under high deformation, while the conventional finite element method is used to model the rest of the system. The elasto-plastic Drucker-Prager Cap model is used to model the soil behaviour. The explosion process is simulated using the Jones-Wilkens-Lee equation of state. The Concrete Damage Plasticity model is used to simulate the behaviour of concrete with the reinforcement considered as an elasto-plastic material. The contact interface between soil and structure is simulated using the general Mohr-Coulomb friction concept, which allows for sliding, separation and rebound between the buried structure surface and the surrounding soil. The behaviour of the whole system is evaluated using a numerical example which shows that the proposed model is capable of producing a realistic simulation of the physical system behaviour in a smooth numerical process.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1540-1555
• /
• 2021

The plate-type fuel assembly adopted in nuclear research reactor suffers from complicated effect induced by non-uniform irradiation, which might affect its stress conditions, mechanical behavior and thermal-hydraulic performance. A reliable numerical method is of great importance to reveal the complex evolution of mechanical deformation, flow redistribution and temperature field for the plate-type fuel assembly under non-uniform irradiation. This paper is the first part of a two-part study developing the numerical methodology for the thermal-fluid-structure coupling behaviors of plate-type fuel assembly under irradiation. In this paper, the thermal-fluid-structure coupling methodology has been developed for plate-type fuel assembly under non-uniform irradiation condition by exchanging thermal-hydraulic and mechanical deformation parameters between Finite Element Model (FEM) software and Computational Fluid Dynamic (CFD) software with Mesh-based parallel Code Coupling Interface (MpCCI), which has been validated with experimental results. Based on the established methodology, the effects of non-uniform irradiation and fluid were discussed, which demonstrated that the maximum mechanical deformation with irradiation was dozens of times larger than that without irradiation and the hydraulic load on fuel plates due to differential pressure played a dominant role in the mechanical deformation.

• 대한조선학회논문집
• /
• 제56권4호
• /
• pp.373-382
• /
• 2019

This paper shows numerical results for the estimation of the propulsor efficiency of Pre-Swirl Duct for 176k bulk carrier as well as its design method. Reynolds averaged Navier-Stokes equations have been solved and the k-epsilon model applied for the turbulent closure. The propeller rotating motion is determined using a sliding mesh technique. The design process is divided into each part of Pre-Swirl Duct, duct and Pre-Swirl Stator. The design of duct was performed first because it is located further upstream than Pre-Swirl Stator. The distribution of velocity through the duct was analyzed and applied for the design of Pre-Swirl Stator. The design variables of duct include duct angle, diameter, and chord length. Diameter, chord length, equivalent angle are considered when designing the Pre-Swirl Stator. Furthermore, a variable pitch angle stator is applied for the final model of Pre-Swirl Duct. The largest reduction rate of the delivered power in model scale is 7.6%. Streamlines, axial and tangential velocities under the condition that the Pre-Swirl Duct is installed were reviewed to verify its performance.

• 한국의상디자인학회지
• /
• 제21권3호
• /
• pp.1-11
• /
• 2019

This study examined the cause of the phenomenon of shrinkage in machine-embroidered fabrics, specifically those made of thin and pliable fabrics. Four woven fabrics and two knitted fabrics were selected as samples for analysis. The fabrics selected were silk organza, flax linen, polyester chiffon, cotton batiste, polyester raschel mesh, and cotton jersey. The thickness and drapability of the fabrics were observed and the shrinkage of the various types of embroidered fabrics produced using satin & step stitch techniques were measured. Moreover, the correlation between the shrinkage of the machine-embroidered fabrics and the drapability of the original fabrics was analyzed. Also, the colorfastness of six embroidery yarns was determined. The results of the study are as follows: first, the shrinkage of machine-embroidered fabrics increased at a greater rate than in embroidered knitted fabrics as compared to rates in embroidered woven fabrics. Moreover, in terms of stitch techniques, there was a greater shrinkage rate when satin stitch was applied compared to step stitch. Second, the shrinkage rate of machine-embroidered fabrics decreased when a stabilizer was fused onto the fabric. The shrinkage rate also decreased for fabrics when fused with paper stabilizer compared to those without it, and the rate decreased at a greater amount with paper stabilizer as compared to alginate film. Third, since there was a strong correlation between the shrinkage rate of the embroidered fabric and the drapability ratio of the original fabric, it was generally the case that the more pliable the fabric was, the greater the shrinkage rate was when the fabric was embroidered. Fourth, while the embroidery yarns mainly used in machine-embroidery presented an overall excellent level of colorfastness, there was slight color migration of level 4 to level 5 when using viscose rayon.