• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.3
• /
• pp.325-335
• /
• 1994

The spinel $MgO.Al_20_3$ single crystals were grown by FZ (floating zone) method. Its melting point is about, $2135^{\circ}C$ and is important to the process of the growth from the melt. There have been some reports of the growth by Czochralski and Verneuil method. However, this study is the first trial to the spinel crystal with the application of FZ method. In this study, $MgAl_2O_4$ spinel crystals were grown by using FZ method which uses the ellipsoidal mirror furnace having infrared halogen lamps as a heat source. With dopants of transition metal ions, it was possible to melt the feed rod which does not absorb the infrared rays due to the transparent properties to infrared ray of spinel itself and the red, green and blue colored spinel single crystals could be grown more easily. As a conclusion, the purpose of this study is to find the spinel single crystal growth mechanism with respect to th growth interfaces and molten zone stability and to characterize the state of growth resulting from the concavity to the melt of interfaces.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.4
• /
• pp.162-166
• /
• 2017

Thermoelectric compounds of $Zn_{1-x}Ag_xSb$ with x = 0~0.2 were prepared by vacuum melting and quenching process and their crystal phases and thermoelectric properties were examined. It was found that free metallic Sb phases were formed in the compound with x = 0.05, leading to increasing the electrical conductivities. The power factors were significantly affected by the electrical conductivity rather than Seebeck coefficient. When x > 0.05, the peak intensities of $Ag_3Sb$ phases in XRD patterns were increased and those of free Sb phases were weakened. These changes of second phases resulted in decreasing the electrical conductivities and the power factors and became more obvious in the compound with x = 0.2.

• Journal of Korean Dental Science
• /
• v.9 no.1
• /
• pp.19-27
• /
• 2016

Purpose: Laser treatment has become a popular method in implant dentistry, and lasers have been used for the decontamination of implant surfaces when treating peri-implantitis. This study was performed to evaluate the effects of an Erbium-doped:Yttrium-Aluminum-Garnet (Er:YAG) laser with different settings on machined (MA), sand-blasted and acid-etched (SA), and resorbable blast media (RBM) titanium surfaces using scanning electron microscopy and confocal microscopy. Materials and Methods: Four MA, four SA, and four RBM discs were either irradiated at 40 mJ/20 Hz, 90 mJ/20 Hz, or 40 mJ/25 Hz for 2 minutes. The specimens were evaluated with scanning electron microscopy and confocal microscopy. Result: The untreated MA surface demonstrated uniform roughness with circumferential machining marks, and depressions were observed after laser treatment. The untreated SA surface demonstrated a rough surface with sharp spikes and deep pits, and the laser produced noticeable changes on the SA titanium surfaces with melting and fusion. The untreated RBM surface demonstrated a rough surface with irregular indentation, and treatment with the laser produced changes on the RBM titanium surfaces. The Er:YAG laser produced significant changes on the roughness parameters, including arithmetic mean height of the surface (Sa) and maximum height of the surface (Sz), of the MA and SA surfaces. However, the Er:YAG laser did not produce notable changes on the roughness parameters, such as Sa and Sz, of the RBM surfaces. Conclusion: This study evaluated the effects of an Er:YAG laser on MA, SA, and RBM titanium discs using confocal microscopy and scanning electron microscopy. Treatment with the laser produced significant changes in the roughness of MA and SA surfaces, but the roughness parameters of the RBM discs were not significantly changed. Further research is needed to evaluate the efficiency of the Er:YAG laser in removing the contaminants, adhering bacteria, and the effects of treatment on cellular attachment, proliferation, and differentiation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.504-508
• /
• 2003

New banana-shaped achiral compounds, 4-chloro-1,3-phenylene bis [4-4(3-fluoro-9-alkenyloxy) phenyl-iminomethylbenzoate]s and 4-chloro-1,3-phenylene bis [4-4-(3-fluoro-10-alkanyloxy) phenyliminomethyl benzoate]s were synthesized by varying the substituent (X=H, F, or Cl); their electrooptical properties are described. The smectic phases, including a switchable chiral smectic C ($SmC^{\ast}$) phase, were characterized by differential scanning calorimetry, polarizing optical microscopy, and triangular method. The presence of vinyl end group at the terminals of linear side wings in the banana-shaped molecules induced a decrease in melting temperature. The smectic phase having the undecenyloxy group such $as-(CH_2)_9CH=CH_2$ showed ferroelectric switching, and its value of spontaneous polarization on reversal of an applied electric field was 2250 $nC/cm^2$, while the value of spontaneous polarization of the smectic phase having the decanyloxy group such as $-(CH2)_9CH_3$ was 3700 $nC/cm^2$. We could obtain the ferroelectric phase with low isotropic temperature by varying the end group at the terminals of linear side wings in the banana-shaped achiral molecules.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.6
• /
• pp.573-580
• /
• 2012

Corrosion resistance and basic physical properties of solid tantalum are not comparable to most of the structural metallic materials. The relative high cost and melting temperature of tantalum are obstacles to be widely applied to general engineering processes. Electrodeposition in molten salt enables compact and uniform tantalum coating. In this study, Ta was coated onto base metal (SUS316L) with different current densities (0.5, 5, $20mA/cm^2$) by using MSE (Molten Salt Electrodeposition). In this study, it showed that deposition efficiency and microstructure of Ta coating layer were strongly depended on current density. In the case of the current density of $5mA/cm^2$, densest microstructure was obtained. The current density above $5mA/cm^2$ caused non-uniform microstructure due to rapid deposition rate. Dense microstructure and intact coating layer contributed to significant corrosion resistance enhancement.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.4
• /
• pp.369-376
• /
• 2012

In this study, to reduce the hydration heat velocity (HHV) of high-strength mass concrete at early ages, phase change materials (PCM) that could absorb hydration heat were applied, and the changes in autogenous shrinkage were investigated, as well as the relationship between the hydration temperature and autogenous shrinkage. The acceleration of the cement hydration process by the PCM leads to an early setting and a higher development of the compressive strength and elastic modulus of concrete at very early ages. The function of PCM could be worked below the original melting point due to the eutectic effect, while the hydration temperature and HHV of high-strength mass concrete can be decreased through the use of the PCM. A close relationship was found between the hydration temperature and autogenous shrinkage: the higher the HHV, the greater the ultimate autogenous shrinkage.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1378-1380
• /
• 2001

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.

• Journal of the Korean Ceramic Society
• /
• v.40 no.2
• /
• pp.159-166
• /
• 2003

The preparation method for composite membranes of high temperature operation above $100^{\circ}C$ for Polymer Electrolyte Membrane Fuel Cells (PEMFCs ) was presented, using perfluorosulfonylfluoride Nafion resin and mordenite, in addition to the physical properties, proton conductivity and single cells performance for it. The composite membranes were fabricated via melting of Nafion resin with various mordenite content. As the increase of mordenite content, at high temperature range, proton conductivity of the composite membrane increased due to the late dehydration rate of existent water in the mordenite. Also, from the result of the current-voltage relationship for single cells under $130^{\circ}C$ operation condition, the composite membrane cell with l0 wt% mordenite content showed better performance than that of the others over the entire current density range. This result indicated that the existent water in the composite membrane with l0 wt% mordenite content was higher than that with the others, thereby maintains its conductivity. Based upon the results of experiments, therefore, a Nafion/mordenite composite membrane prepared by this work is thought to be a satisfactory polymer electrolyte membrane for PEMFC operation above $100^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.195-195
• /
• 2008

CAS계 유리에 $CaCO_3-Al_2O_3$ 혼합물 및 화합물을 10, 30 wt% 첨가하여 저온 소걸 및 마이크로파 유전 특성을 고찰하였다. CAS계 유리의 연화온도는 $841^{\circ}C$ 이며, CAS계 유리에 $CaCO_3$ 와 30 wt%의 $CaCO_3-Al_2O_3$ 혼합물을 melting되며, 10 wt%의 $CaCO_3$, $Al_2O_3$, $1CaCO_3-1Al_2O_3$ 혼합물 및 $CaAl_2O_4$ 화합물를 10 wt% 첨가하였을 때 $900^{\circ}C$ 이하에서 소걸이 가능하였다. 복합체의 XRD 상 분석 결과, CaCO3를 첨가하였을 때에는 모든 조성이 비정질을 나타내었고, $Al_2O_3$와 $1CaCO_3-1Al_2O_3$ 혼합물은 $Al_2O_3$ 결정상이 생성되었고, $CaAl_2O_4$ 화합물은 $CaAl_2Si_2O_8$의 hexagonal와 anorthite 결정상이 생성되었다. 따라서 CAS-10 (A, C-A, CA) 복합체는 $900^{\circ}C$에서 각각 유전율 ($\varepsilon_r$) 6.4, 6.9, 5.15 와 품질계수 ($Q^*f$) 2,400, 1,500, 3,000의 마이크로파 유전 특성을 나타내어 LTCC 기판 재료로 사용이 가능하며, 특히 $CaAl_2O_4$ 화합물을 사용하였을 때 가장 우수한 유전 특성을 나타내는 것을 확인하였다.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.26 no.2
• /
• pp.93-98
• /
• 2020

The blends of Poly(lactic acid) (PLA) and Poly(butylene adipate-co-terephthalate) (PBAT) have been recognized as a replacement for commodity plastic films and bags in biodegradable packaging industries. The purpose of this study is to identify changes in the thermal and mechanical properties of PLA/PBAT blends with the addition of poly(ethylene oxide)(PEO). PLA (80%) and PBAT (20%) were melt mixed with 0 to 10 phr of PEO and processed using a hot press. The addition of PEO into PLA/PBAT increased the elongation at break and improved thermal stability. With PEO addition, two melting temperature (T_m) peaks of PLA/PBAT merged into one peak showing improved miscibility. The result of this study showed that the addition of PEO increased the ductility and thermal stability of PLA/PBAT blends.