• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.204-210
• /
• 2013

Effects of additives (lubricant and antioxidant) and melt-blending condition (temperature, time and rotor speed) on the mechanical properties of polypropylene-based wood polymer composites (WPCs) were investigated. WPCs were prepared by melt-blending followed by compression molding. To understand melt-blending procedure, torque change of the WPC melt-blend was monitored. Maleic anhydride modified PP and nanoclay were used as a compatibilizer and a reinforcing filler, respectively. UTM and izod impact tester were used to measure the mechanical properties of the WPCs and a color-difference meter was used to measure the discoloration of the WPCs according to melt-blending condition. The mechanical properties showed that the optimized melt-blending condition was $170^{\circ}C$, 15 min, and 60 rpm. The mechanical properties of the WPCs decreased with increasing lubricant and antioxidant content. The two step method, adding wood flour later separately during melt-blending, was more effective than the typical one step method for improving the mechanical properties of the WPCs.

• Journal of Korea Foundry Society
• /
• v.23 no.2
• /
• pp.69-76
• /
• 2003

The present work was undertaken to investigate the mutual effect of the individual melt treatment commonly applied in aluminum foundries such as grain refining, modification, degassing and filtration on the microstructures and the mechanical properties. A357 alloys were fabricated through various melt treatments such as degassing by gas bubbling filtration, modification via the addition of Al-Sr master alloy, grain refining through the addition of Al-Ti-B master alloy and filtration before pouring of the melt. Each melt treatment was performed at its optimum condition reported in the literatures. The effects of each melt treatment and their interactions on the microstructures and mechanical properties of A357 alloy were examined.

• Textile Coloration and Finishing
• /
• v.12 no.5
• /
• pp.295-300
• /
• 2000

The melting behavior of hydrated polyacrylonitrile (PAN) and the rheological properties of hydrated PAN melt were investigated using DSC md modified capillary rheometer. With increasing the water content, Tm of the hydrated PAN was rapidly decreased and finally levelled off above a critical water content. However, the melt viscosity was further decreased even above the critical water content. The hydrated PAN melt showed a typical shear thinning behavior. In arrhenius plot, when the hydrated PAN melt was supercooled, it exhibited a different dependency on temperature from that above melting temperature.

• Korea-Australia Rheology Journal
• /
• v.12 no.3_4
• /
• pp.181-186
• /
• 2000

Rheological Properties of polypropylenes having different molecular structures (linear polypropylene (PPL) and branched one (PPB)) were studied. Both the extensional flow and oscillatory shear flow properties were checked. Especially, the melt strength of polypropylenes having various shear history were investigated by using in-house-made Rheometer (called SMER). Compared to linear polypropylene, the branched polypropylene shows enhanced melt strength during extensional flow due to the retarded relaxation of molecules. When the slope of melt tension was plotted against take up speed of melt strand, the characteristic peak was observed in case of branched polypropylene, while the linear polypropylene shows only monotonously decreasing pattern. This entanglement was partially disrupted by physical forces such as shear during melt extrusion. However, the melt strength of PPB after multiple extrusion is still higher than PPL, implying the loss of elasticity during multiple extrusion is not so comprehensive. On dynamic experiments, PPB shows typical shear thinning behavior and the tangent delta of PPB is lower than PPL, reflecting high elasticity of PPB.

• Journal of Korea Foundry Society
• /
• v.30 no.3
• /
• pp.111-114
• /
• 2010

The effects of grain refinement and melt stirring on the mechanical properties and fluidity of AZ91D and AM50 alloys were investigated. The average grain sizes of those alloys were reduced by the micro-addition of strontium. The tensile properties and fluidity were increased by this treatment. Those were reduced remarkably by the melt stirring.

• Analytical Science and Technology
• /
• v.8 no.3
• /
• pp.341-350
• /
• 1995

$Nd_{14}Fe_{80}B_6$ ribbon alloy was manufactured with using melt-spinning method and analyzed the magnetic properties according to the manufacturing conditions. The microstructure and magnetic properties of melt-spun ribbons are sensitively dependent on the quench rate and annealing conditions. As-quenched $Nd_{14}Fe_{80}B_6$ ribbons with optimum magnetic properties are obtained at wheel speed($v_s$) of about 20m/sec and over quenched ribbons show optimum magnetic properties at $v_s$=22m/see when annealed for 30 minutes at $600^{\circ}C$ under vacuum. The crystallization temperature($T_k$) of $Nd_2Fe_{14}B$ phase is about $595^{\circ}C$ in the DTA analysis.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.194-202
• /
• 1996

Hot melt adhesive based on the polyamide resin was studied to improve the conventional hot melt adhesives such as ethylene-vinyl acetate which have inherent problems against creep and heat resistance. It was found that the terpolymer of nylons6, nylon66, and nylon12 or the nylon blend instead of nylon homopolymer was suitable base resin for hot melt adhesives, since the disruption of regularity in the polymer chains reduced the crystallinity, resulting in lower melting point and melt viscosity. Also, the rheological properties of the polyamide based hot melt adhesive could be controlled by the incorporation of terpene resin, butyl benzyl phthalate, and paraffin wax. The results of melt viscosities and tensile properties of adhesive itself indicated that the optimum adhesion properties could be obtained through the blending of CM831/843P resins with weight ratio 75/25~50/50. The adhesion between steel and steel was tested by using lap shear geometry. It was found that the surface roughness of steel affected the adhesion strength.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.265-268
• /
• 2005

Thermoplastic elastormer (TPE) has many advantages such as high flexibility, high elasticity and high elongation, etc. TPE is easily molded such as plastic materials, therefore, many TPE parts are applied as home appliances and mechanical parts. However, if TPE is once molded, its mechanical properties are changed by injection molding conditions such as melt temperature, mold temperature, injection pressure and holding pressure, etc. In this study, the influences of the injection molding condition on the mechanical properties of thermoplastic vulcanizates(TPVs), which is one of the TPE, were investigated. By the injection molding experiment, as increasing the melt temperature, the tensile strength, shrinkage and hardness decreased. By the scanning electron microscope (SEM) analyzing the TPVs' crystallization, the morphology was affected by the melt temperature.

• Textile Coloration and Finishing
• /
• v.21 no.6
• /
• pp.22-28
• /
• 2009

Oil-absorbable nonwovens were produced by melt-blown processing of polypropylene chips. The melt-blown processing conditions, such as air pressure, and gear pump speed, DCD. In this study, these three factors were chosen to produce samples. Experimental array and variance analysis of the design of experiment were used to increase the field repeatability and universality. The effect of the factors on oil absorption properties of melt-blown nonwoven fabric such as oil absorbency were evaluated. As a result, the fiber diameter decreased as gearpump speed decreased or air pressure increased. The oil absorbency increased as air pressure increased or gearpump speed decreased and with the DCD increasing the oil absorbency significantly increased.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1289-1293
• /
• 2018

The influence of crystallization treatment on the structure, magnetic properties and magnetocaloric effect of $Gd_{71}Ni_{29}$ melt-spun ribbons has been investigated in detail. Annealing of the melt-spun samples at 610 K for 30 min, a majority phase with a $Fe_3C$-type orthorhombic structure (space group, Pnma) and a minority phase with a CrB-type orthorhombic structure (space group, Cmcm) were obtained in the amorphous matrix. The amorphous melt-spun ribbons undergo a second-order ferromagnetic to paramagnetic phase transition at 122 K. For the annealed samples, two magnetic phase transitions caused by amorphous matrix and $Gd_3Ni$ phases occur at 82 and 100 K, respectively. The maximum magnetic entropy change $(-{\Delta}S_M)^{max}$ is $9.0J/(kg{\cdot}K)$ (5T) at 122 K for the melt-spun ribbons. The values of $(-{\Delta}S_M)^{max}$ in annealed ribbons are 1.0 and $5.7J/(kg{\cdot}K)$, corresponding to the two adjacent magnetic transitions.