• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.942-945
• /
• 2005

Micron-sized metal wires are widely used in industries such as filtration, catalyst and composite materials, etc. In the wire drawing process, the die that is used conventionally is an effective and, at the same time, sensitive component. However, a typical array of the dies has caused many problems in the wire drawing process, e.g., large frictional force on the interface between wire and the resulting high heat generation, precise adjustment of the dies, extended cooling system, die abrasion, etc.. Because of these problems, there have been many works that are aiming at improving the efficiency of wire drawing process by analyzing the die geometry and by applying advanced die material to prolong the die life or even at developing a dieless wire drawing system. This paper is dealing with developing a new wire drawing system that is applicable to reduce the wire drawing steps with high draw ratio. The new wire drawing system does not use the dies, but use the self-induced heater that works on the basis of the resonant phenomenon of wire material. The electromagnetic wave is the heating source. The results of the study on the diameter reduction and microwave flow analysis show that the heating effectiveness of the wire is influenced by the energy distribution in the microwave propagation chamber. We can obtain diameter-reduced wires by using microwave in the dieless drawing process. Microwave as a heating source is capable of producing wires without applying dies in wire drawing process.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.153-159
• /
• 2007

Nano-Particles are influenced on the environmental protection and human health. The relationships between transient vehicle operation and nano-particle emissions are not well-known, especially for diesel passenger vehicles with DPF. In this study, a diesel passenger vehicle was measured on condition of DPF regeneration and no regeneration on a chassis dynamometer test bench. The particulate matter (PM) emission from this vehicle was measured by its number, size and mass measurement. The mass of the total PM was evaluated with the standard gravimetric measurement method while the total number and size concentrations were measured on a NEDC driving cycle using Condensation Particle Counter (CPC) and EEPS. Total number concentration by CPC was $1.5{\times}10^{1l}N/km$, which was 20% of result by EEPS. This means about 80% of total particle emission is consist of volatile and small-sized particles(<22nm). During regeneration, particle emission was $6.2{\times}10^{12}N/km$, was emitted 400 times compared with the emission before regeneration. As for the particle size of $22{\sim}100nm$ was emitted mainly, showing peak value of near 40nm in size. This means regeneration decreased the mean size of particles. Regarding regeneration, PM showed no change while the particle number showed about 6 times difference between before and after regeneration. It seems that the regeneration influences on particle number emissions are related to DPF-fill state and filtration efficiency.

• 한국유체기계학회 논문집
• /
• 제19권4호
• /
• pp.48-53
• /
• 2016

The centrifugal separator which uses gravity separation method for oil-water separation, rotating at high-speed, is one of the most commonly used device for controlling the amount of the oil in waste water collected in bilge. The IMO (International Maritime Organization) has set regulations, also known as MARPOL 73/78, for the prevention of marine pollution. In addition, DET NORSKE VERITAS (DNV) has set standards regarding the assignment of Environmental Class Notation, CLEAN or CLEAN DESIGN, of ships. One of the requirements for classification is that in addition to conforming to MARPOL 73/78, more stringent measures must be taken as well. One of these measures is to limit the oil concentration in bilge water to less than 5ppm. So in this study, an Oil-Water Separator (OWS) is used together with multiple separating plates as a filtration system to be used as an oil-water separation device. The OWS operates using centrifugal separation in which the mixture is separated by centrifugal forces. The main purpose of this paper is to present the OWS separation efficiency according to the rotation speed, mass-flow rate, the angle and the number of stacked layers of the laminated plate using Computational Fluid Dynamics (CFD). Improvements to the device will be investigated from these results.

• 자원리싸이클링
• /
• 제29권1호
• /
• pp.70-80
• /
• 2020

본 연구에서는 유도로를 사용하여 알루미늄 캔 스크랩의 재활용 효율을 플럭스 종류와 혼합 비율의 영향에 대해 조사하였다. 알루미늄 캔 제조 공정에서 발생한 알루미늄 캔 스크랩의 표면 코팅층 약 500 ℃에서 30 분간 열처리를 통해 제거가 가능하였다. 용해 공정 온도는 알루미늄 합금 용해 온도보다 높은 온도로 설정하였고, 플럭스 종류와 혼합 비율에 따른 용탕처리를 진행하였다. 그 결과, 750 ℃에서 3 wt.%의 플럭스(Salt flux와 MgCl₂ 혼합비율 70:30)의 조건에서 알루미늄을 최적으로 회수 할 수 있었다. 회수된 Al합금은 인장강도 249 MPa과 연신율 14 %로써 Al5083 소재와 거의 동일한 기계적 특성을 나타냄을 알 수 있었다.

• 대한환경공학회지
• /
• 제28권10호
• /
• pp.1009-1015
• /
• 2006

정수 슬러지의 감량화와 탈수장치의 성능향상을 위하여 필터프레스 탈수장치의 각 Plate 사이에 음극판과 양극판을 설치하여 케이크 층에 전기장을 투입하는 전기식 필터프레스 탈수장치(EDFP)를 구축하여 기존의 기계식 필터프레스 탈수장치(MDEF)와의 탈수성 비교, 그리고 EDFP의 탈수성 향상에 따른 경제적인 측면 등을 분석하였다. 동일조건에서 탈수실험을 수행한 결과 EDFP를 통해 배출된 여액량은 43.2 kg으로 MDFP에 비하여 증가하였으며, 케이크 무게는 4 kg으로 MDFP에 비해 2배 증가하였고 탈수 케이크의 함수율은 55 wt%로 MDFP에 비하여 약 20% 감소하였으며 탈수속도는 2.3 $kg/m^2{\cdot}cycle$로 약 30% 증가하였다. 즉 전기탈수(Electrodewatering)의 원리로 구축된 EDFP는 기계탈수(Mechanical Dewatering)에 의한 MDFP 비하여 여액배출량을 증가시키고 저함수율 탈수 케이크를 생산하며 탈수속도를 증가시키는 특성이 있다. EDFP의 소모된 전력량은 400 kwh/DS ton으로, 투입된 전력량과 저함수율 탈수 케이크 생산에 따른 부피 감소로 인한 처리경비 저하의 효과를 서로 고려하여 경제성을 분석한 결과 1 ton(Dry Solid base) 처리하는데 약 20,000원 경제적 절감 효과가 있었다. 이 외 탈수속도가 빨라진 부가적 이점을 감안하면, EDFP는 탈수 성능 면에서 우수할 뿐만 아니라 경제적 타당성이 있는 장치로 평가할 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.311-311
• /
• 2009

Carbon nanotubes (CNTs) belong to an ideal material for field emitters because of their superior electrical, mechanical, and chemical properties together with unique geometric features. Several applications of CNTs to field emitters have been demonstrated in electron emission devices such as field emission display (FED), backlight unit (BLU), X-ray source, etc. In this study, we fabricated a CNT cathode by using filtration processes. First, an aqueous CNT solution was prepared by ultrasonically dispersing purified single-walled CNTs (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). The aqueous CNT solution in a milliliter or even several tens of micro-litters was filtered by an alumina membrane through the vacuum filtration, and an ultra-thin CNT film was formed onto the alumina membrane. Thereafter, the alumina membrane was solvated by acetone, and the floating CNT film was easily transferred to indium-tin-oxide (ITO) glass substrate in an area defined as 1 cm with a film mask. The CNT film was subjected to an activation process with an adhesive roller, erecting the CNTs up to serve as electron emitters. In order to measure their luminance characteristics, an ITO-coated glass substrate having phosphor was employed as an anode plate. Our field emitter array (FEA) was fairly transparent unlike conventional FEAs, which enabled light to emit not only through the anode frontside but also through the cathode backside, where luminace on the cathode backside was higher than that on the anode frontside. Futhermore, we added a reflecting metal layer to cathode or anode side to enhance the luminance of light passing through the other side. In one case, the metal layer was formed onto the bottom face of the cathode substrate and reflected the light back so that light passed only through the anode substrate. In the other case, the reflecting layer coated on the anode substrate made all light go only through the cathode substrate. Among the two cases, the latter showed higher luminance than the former. This study will discuss the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the either side.

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.754-757
• /
• 2012

본 연구에서는 embossing 공정과 진공여과법에 의해서 제조된 다공성 그래핀 필름을 슈퍼캐패시터의 전극활물질로 사용하여 우수한 전기화학적 특성을 증명하였다. 그래핀 시트사이에서 Polystyrene 입자들의 삽입/제거 공정을 이용하여 기공 구조들을 제공함으로써 그래핀의 재적층(restacking)을 효과적으로 제어할 수 있었다. 상기 제조된 다공성 그래핀 필름은 넓은 표면적, 상호 연결된 기공 구조, 높은 전기전도도 및 우수한 기계적 물성을 나타내었다. 본 다공성 그래핀 필름을 슈퍼캐패시터의 전극물질로 사용하여 황산 수용액과 이온성 액체 전해질 기반의 3상 전극 시스템에서 전기화학적 특성을 살펴보았다. 다공성 그래핀 필름은 높은 비축전용량(284.5 F/g)을 나타내었으며, 이는 적층 그래핀 필름(138.9 F/g) 보다 두 배 정도 높았다. 또한, 그래핀 필름내의 이온 이동속도 향상 효과로 다공성 그래핀 필름의 충방전 속도(98.7% retention)와 충방전 수명(97.2% retention)이 크게 향상되었다.

• 대한환경공학회지
• /
• 제31권9호
• /
• pp.743-748
• /
• 2009

화학적인 슬러지 개량은 하수슬러지의 탈수성을 개선하기 위해 주로 사용된다. 이 공정은 개량제를 이용하여 처리한 후 농축 및 탈수된다. 본 연구는 DAF 부상장치를 이용하여 하수슬러지의 개량(혐기성 보관시간, 응집제 종류, 및 주입량) 및 부상조건(슬러지 농도 및 A/S 비)에 따른 부상농축효율을 평가한 것이다. 혐기성 보관시간에 따라 하수슬러지의 비표면적과 여과비저항은 증가하였다. $Al_2(SO_4)_3$, $Fe_2(SO_4)_3$ 및 PSO-M을 주입하여 개량된 하수슬러지는 보관시간이 경과에 따라 부상농축효율이 거의 감소되지 않았다. 개량된 하수슬러지는 A/S 비가 0.01 mL/mg 이상이면, 부상농축효율이 저하되지 않고 96% 이상 유지할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.353-353
• /
• 2008

Carbon nanotubes (CNTs) are attractive for field emitter because of their outstanding electrical, mechanical, and chemical properties. Several applications using CNTs as field emitters have been demonstrated such as field emission display (FED), backlight unit (BLU), and X-ray source. In this study, we fabricated a CNT cathode using transparent ultra-thin CNT film. First, CNT aqueous solution was prepared by ultrasonically dispersing purified single-walled carbon nanotubes (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). To obtain the CNT film, the CNT solution in a milliliter or even several tens of micro-litters was deposited onto a porous alumina membrane through vacuum filtration process. Thereafter, the alumina membrane was solvated by the 3 M NaOH solution and the floating CNT film was easily transferred to an indium-tin-oxide (ITO) glass substrate of $0.5\times0.5cm^2$ with a film mask. The transmittance of as-prepared ultra-thin CNT films measured by UV-Vis spectrophotometer was 68~97%, depending on the amount of CNTs dispersed in an aqueous solution. Roller activation, which is a essential process to improve the field emission characteristics of CNT films, increased the UV-Vis transmittance up to 93~98%. This study presents SEM morphology of CNT emitters and their field emission properties according to the concentration of CNTs in an aqueous solutions. Since the ultra-thin CNT emitters prepared from the solutions show a high peak current density of field emission comparable to that of the paste-base CNT emitters and do not contain outgassing sources such as organic binders, they are considered to be very promising for small-size-but-high-end applications including X-ray sources and microwave power amplifiers.

• 한국물환경학회지
• /
• 제32권6호
• /
• pp.600-627
• /
• 2016

Korea is one of the countries with a large veterinary antibiotics market, although antimicrobial resistance in bacteria is becoming a serious issue in many countries. The Korean government started to take interest in estimating the effects of livestock manure on rivers and agricultural soils and in monitoring of heavy metals, organic pollutants and antibiotics in the ambient water and soil. In this paper, pre-treatment methods to separate the selected antibiotics from solid samples were reviewed. It is essential to select an efficient and appropriate procedure for pre-treatment due to the high proportion of proteins and organics in biosolid samples. Pre-treatment consists of extraction followed by clean-up. Initially, homogenized samples were extracted by sonication, mechanical agitation or pressurized liquid extraction with methanol/acetonitrile/water mixture under acidic/basic conditions depending on the compound. However, aminoglycosides and colistin were extracted with 5% trichloroacetic acid and HCl, respectively. Since the ${\beta}-lactams$ are easily decomposed in acidic and basic conditions, they were extracted in neutral pH. Filtration with a membrane (pore size, $0.2{\mu}m$) or solid phase extraction with HLB and methanol, as eluents, was normally applied for the clean-up. At least, three different pre-treatment procedures should be adopted to screen all the selected antibiotics in solid samples.