• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.37-42
• /
• 2005

The non-destructive Inspection of the fillet weldment has difficulties due to its geometrical complexity and uneasy access. The surface shear horizontal wave (SH-wave), however, has been successfully applied to the detection of cracks on the surface and sub-surface of the filet weldment heel part. The conventional ultrasonic inspection using the surface SH-wave is usually a contact method using piezoelectric transducer. Thus, it is not suitable for a field application because the reliability and repeatability of inspection are significantly affected by test conditions such as couplant, contact pressure and pre-process. In order to overcome this problem, a non-contact SH-wave inspection method using EMAT is propose. The experimental results with this non-contact method are compared with those with a conventional ultrasonic method in fillet weldment with slit type defects. It is shown that the non-contact inspection technique requires simple procedure and less time in the fillet weldment inspection.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.47-47
• /
• 2010

지구온난화의 심화로 사회적으로 환경의 중요성에 대한 인식이 확산되면서 $CO_2$ 배기가스 및 연비와 직결되어 있는 자동차 중량 절감의 중요성이 강조됨에 따라 차체 경량화 기술은 환경 친화적인 자동차 개발의 핵심기술로 연구되고 있다. 그러나 충돌보호 장치 및 편의장치의 증가로 차체 중량은 지속적으로 증가하고 있어 차체 중량을 혁신적으로 절감할 수 있는 초경량 차체기술이 요구된다. 차체 경량화 방법으로 기존 강재를 알루미늄재로 대체하는 방안이 연구되고 있으며, 일부 해외 고급 차종에서 알루미늄재를 이용한 스페이스 프레임 및 부품 개발을 검토 적용 중이다. 그러나 알루미늄 단일재 사용은 안전성등에서 요구 성능을 만족시키기 어렵기 때문에 강재와 알루미늄재의 적절한 사용이 필요하다. 이를 위하여 강재와 알루미늄간 이종접합부가 발생하며 이를 위한 적정 공정 개발이 필요하다. 전자기 펄스 용접(MPW)은 고상접합의 한 종류로서 고전류를 순간적으로 방전하여 발생된 고에너지를 통하여 접합이 이루어진다. 이러한 고에너지는 외부재의 전 자기적 성질에 의하여 에너지량이 결정되므로 외부재의 전도도(conductivity)는 매우 중요하며 이러한 이유로 Aluminum 1xxx계 중심의 전자기 펄스 용접 공정이 연구되었다. 그러나 자동차 스페이스 프레임 및 드라이브 샤프트등과 같은 부품에 알루미늄재를 적용하기 위해서는 일정 강도를 확보할 수 있는 6xxx계의 관련 연구가 필요하다. 따라서 본 연구에서는 고품질의 접합부 확보를 위한 1xxx계와 6xxx의 최적의 공정변수(충전전압, 외부재와 내부재 사이의 간격, 외부재 두께)를 도출하였다. 이를 위하여 전자기 펄스 용접 장치는 한국생산기술연구원과 웰메이트(주)에서 공동으로 개발한 $120{\mu}F$의 캐패시터 6개로 구성된 'W-MPW36'을 사용하였으며 접합 후 누수시험을 통하여 접합부의 품질을 검토하였다.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.41-46
• /
• 2010

The low alloy-steel material(1.0Cr-0.5Mo, SA213T12), which has widely been used for the waterwall tube in the conventional power plant, do not have enough creep rupture strength for waterwall tubes of the Ultra-supercritical(USC) boilers. According to this reason, the high-strength low alloy-steel(2.25Cr-1.0Mo, SA213T22) has newly been adopted for the waterwall tube in the USC boilers. This paper presents failure analysis on weld-joint of the waterwall tubes in USC boilers. Visual inspections were performed to find out the characteristics of the fracture. Additionally both microscopic characteristics and hardness test were carried out on failed tube samples. Failures seem to happen mainly because the welding process has not been conducted strictly.(preheating, P.W.H.T and so forth). Thus, this paper has the purpose to describe the main cause of the poor welding process and to explain how to prevent similar failures in those weld-joints.

• 대한공업교육학회지
• /
• v.31 no.1
• /
• pp.211-225
• /
• 2006

Gabion can be used for the purpose of preventing overflow of river and side loss of road. However the manufacturing process of the gabion is manually controlled especially to the joining process at the terminal part of gabion with small diameter wire. In this paper automatic feeding guide system was designed and fabricated to make automation. The fabricated system was tested in the factory level. Pneumatic system was considered as the main idea of the feeding system. 3/2-way and 5/2-way manual control valve, eight double-acting cylinders were used. The system took 46.48 seconds during a cycle. Additional environmental noise and vibration were not detected when the machine operated at the working area. Based on the theoretical simulation and actual test the fabricated system was well controlled. The system was applied to the patent in 2006.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.331-338
• /
• 2017

This study was carried out to investigate the optimum condition of a friction stir welding process for a joint of AA2219-T87 and AA2195-T8 dissimilar aluminum alloys. These alloys are known to have good cryogenic properties, and as such to be suitable for use in fuel tanks of space vehicles. The welding parameters include the travelling speed, rotation speed and rotation direction of the tool. The experiment was conducted under conditions in which the travelling speed of the tool was 120-300 mm/min and the rotation speed of the tool was 400-800 rpm. To investigate the effect of the rotation direction of the tool, the joining was performed by switching the positions of the two dissimilar alloys. After welding, the microstructure was observed and the micro-hardness were measured; non-destructive evaluation was carried out to perform tensile tests on defect-free specimens. The result was that the microstructure of the weld joint underwent dynamic recrystallization due to sufficient deformation and frictional heat. The travelling speed of the tool had little effect on the properties of the joint, but the properties of the joint varied with the rotation speed of the tool. The conditions for the best joining properties were 600 rpm and 180-240 mm/min when the AA2219-T8 alloy was on the retreating side(RS).

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.58.1-58.1
• /
• 2010

In solar cell module manufacturing, single solar cells has to be joined electrically to strings. Copper stripes coated with tin-silver-copper alloy are joined on screen printed silver of solar cells which is called busbar. The bus bar collects the electrons generated in solar cell and it is connected to the next cell in the conventional module manufacturing by a metal stringer using conventional hot air or infrared lamp soldering systems. For thin solar cells, both soldering methods have disadvantages, which heats up the whole cell to high temperatures. Because of the different thermal expansion coefficient, mechanical stresses are induced in the solar cell. Recently, the trend of solar cell is toward thinner thickness below 180um and thus the risk of breakage of solar cells is increasing. This has led to the demand for new joining processes with high productivity and reduced error rates. In our project, we have developed a new method to solder solar cells with a laser heating source. The soldering process using diode laser with wavelength of 980nm was examined. The diode laser used has a maximum power of 60W and a scanner system is used to solder dimension of 6" solar cell and the beam travel speed is optimized. For clamping copper stripe to solar cell, zirconia(ZrO)coated iron pin-spring system is used to clamp both joining parts during a scanner system is traveled. The hot plate temperature that solar cell is positioned during lasersoldering process is optimized. Also, conventional solder joints after $180^{\circ}C$ peel tests are compared to the laser soldering methods. Microstructures in welded zone shows that the diffusion zone between solar cell and metal stripes is better formed than inIR soldering method. It is analyzed that the laser solder joints show no damages to the silicon wafer and no cracks beneath the contact. Peel strength between 4N and 5N are measured, with much shorter joining time than IR solder joints and it is shown that the use of laser soldering reduced the degree of bending of solar cell much less than IR soldering.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1195-1203
• /
• 2012

Welding is a well-developed, widely used process for permanently joining metal components. However, the mechanical reliability of welded parts still offers room for improvement. A weld region consists of a fusion zone, a partially melted zone, and a heat-affected zone, and each zone has different material properties. In addition, the geometrical shape of a weld bead or fillet influences the mechanical reliability. A precise structural analysis must consider how a local welded region influences the mechanical behavior of the entire structure. This study focuses on an effective modeling scheme for the weld region. It relies on experimental and numerical methods to determine the proper correlation based on experimental results and to propose a modeling scheme for welded parts.

• International Journal of Korean Welding Society
• /
• v.1 no.2
• /
• pp.36-44
• /
• 2001

To get the appropriate welding process variables, mathematical modeling in conjunction with many experiments is necessary to predict the magnitude of weld bead shape. Even though the experimental results are reliable, it has a difficulty in accurately predicting welding process variables for the desired weld bead shape because of nonlinear and complex characteristics of welding processes. The welding condition determined for the desired weld bead shape may cause the weld defect if the welding current/voltage/speed combination is improperly selected. In this study, the $2^{n-1}$ fractional factorial design method and correlation parameter were used to investigate the effect of the welding process variables on the fillet joint shape, and the multiple non-linear regression analysis was used for modeling the gas metal arc welding(GMAW）parameters of the fillet joint. Finally, a fuzzy rule-based method and a neural network method were proposed so that the complexity and non-linearity of arc welding phenomena could be effectively overcome. The performance of the proposed neuro-fuzzy system was evaluated through various experiments. The experimental results showed that the proposed neuro-fuzzy system could effectively check the welding conditions as to whether or not weld defects would occur, and also adjust the welding conditions to avoid these weld defects.

• Proceedings of the KWS Conference
• /
• 1999.10a
• /
• pp.43-46
• /
• 1999

It has been suggested that the motivation for automation of welding processes ncludes the replacement and extension of the functions of human operators. Among these types of the welding automation, SAW(Submerged Arc Welding) was prevalently used, because it is highly suited to a wide range of application, especially for the high speed welding. A Significant portion of the total manufacturing time for a pipe fabrication process is spent on the welding following primary machining and fit-up processes. To achieve the reliable weld bead appearance, the automatic seam tracking and adaptive control to fill the groove are urgently needed. This paper proposed the mechanical functions of multi-torches welding system, flux supply and recovery system in conjunction with the complex air pulsing method and various types of methodologies. It was shown that the multi-torches welding system revealed the high welding qualities for the circular and rectangular pipes. In conclusion, the multi-torches welding system developed will contribute the advanced welding technology, welding automation and increment of the market in these areas.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.153-155
• /
• 2004

Vibration occurs due to the wind and vehicles, etc., in the field welded joints of steel bridges. However, the effect of vibration on the fatigue strength of field welded joints in steel bridge are not yet clearly understood. In this paper, the effect of vibration on the fatigue strength of welded joints was elucidated in order to improve reliability in the field welded joints of steel bridge. The base material used in this investigation was SM 490A steel of weldable grade. Flux Cored Arc Welding(FCAW) process was used to fabricate the doubte 'V' butt joints. Welding was performed on the steel under the mechanical vibration of given frequency. The applied frequency was resonant frequency. Also, weldments formed under no vibration were fabricated. Fatigue tests were conducted using a servo hydraulic controlled 50ton1 capacity UTM with a frequency of 5Hz under constant amplitude loading.