• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.6
• /
• pp.34-44
• /
• 1996

In order to examine the accuracy of the intensity method, the fiber orientation-angle distribution of fiber-reinforced polymeric composites is measured using image processing. The fiber orientation function is calculated from the fiber orientation measured by the soft X-ray photograph. Theoretical and experimental results of fiber orientation function are compared for the composites with different fiber contents and fiber orientations. The intensity method is used for the experimental investigation and the measured fiber orientation function is compared to the calculated one. The relations between the measured and the simulated fiber orientation functions $J{\small{M}}$ and $J{\small{S}}$ respectively are identified. For the fiber length of 1.000mm and 2.000mm, it shows that $J{\small{M}}=0.83J{\small{M}}$. However. in general. the value of $J{\small{M}}$ decreases as the fiber length increases. For GFRP composites the relations between $J{\small{M}}$ and theoretical value J show that $J{\small{M}}$=0.73J for short fiber and $J{\small{M}}$=0.81J for long fiber.

• Journal of Welding and Joining
• /
• v.27 no.4
• /
• pp.67-72
• /
• 2009

In this paper, arc characteristics of V groove joints using pulsed GMA welding were found out. The bevel angles of $22.5^{\circ}$ and $30.0^{\circ}$ were chose to make the V groove configuration with the groove angles of $45^{\circ}$ and $60.0^{\circ}$, respectively. In the experiment, the arc current waveform measurement and the high speed photography were taken to investigate the arc characteristics for a single-beveled asymmetric workpiece. Consequently, the welding current was changed abnormally around the edge of groove. As the arc moved close to the groove face, the welding current was increased rapidly because the welding arc was affected by the inclined surface. Also the welding current waveforms were measured for the double-sided symmetric workpiece to verify the previous measurements for the single-beveled workpiece, and similar current waveforms were found.

• Journal of the Korean Academy of Clinical Electrophysiology
• /
• v.2 no.1
• /
• pp.9-17
• /
• 2004

The purpose of this study are to determine the proper radiographic measurements for hip deformity in spastic cerebral palsy patients, and the correlation of hip deformity with neurological involvement, ability of ambulation. Thirty children with cerebral palsy(22 males, 8 females) were evaluated by measurement of the migration index, acetabular index, center edge angle from bilateral hip APs(anterior posterior view). The result are as follows; 1. The incidence of hip dislocation, among the thirty children fifteen children were found to be dislocated, and more significantly high in non-walking group than in walking group(p<0.05) and in quadriplegia than in diplegia(p<0.05). 2. When compared to normal hip and dislocation hip, the migration index was significantly higher(p<0.01) and the center edge angle was lower in the dislocation hip than in the normal hip. 3. Correlation of radiological findings in right and left hip, the migration index and the center edge angle were highly correlated(p<0.01). We recommand regular intervals X-ray study for early diagnosis and management of hip dislocation in spastic cerebral palsy.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.68-76
• /
• 2014

This paper presents an offset error compensation algorithm for the accurate phase angle of the grid voltage in single-phase grid-connected inverters. The offset error generated from the grid voltage measurement process cause the fundamental harmonic component with grid frequency in the synchronous reference frame phase lock loop (PLL). As a result, the grid angle is distorted and the power quality in power systems is degraded. In addition, the dq-axis currents in the synchronous reference frame and phase current have the dc component, first and second order ripples compared with the grid frequency under the distorted grid angle. In this paper, the effects of the offset and scaling errors are analyzed based on the synchronous reference frame PLL. Particularly, the offset error can be estimated from the integrator output of the synchronous reference frame PLL and compensated by using proportional-integral controller. Moreover, the RMS (Root Mean Square) function is proposed to detect the offset error component. The effectiveness of the proposed algorithm is verified through simulation and experiment results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.495-496
• /
• 2008

This paper describes the influence of Ultra-violet irradiation on time to tracking resistance of epoxy insulating materials by use of the inclined plane test. And, the influence of surface degradation was evaluated through several method such as measurement of contact angle, surface roughness, using a scanning electron microscopy. As the 1000 hours of the surface degradation with UV-CON, the flashover time decreases at different rates depending on epoxy resin and silicone rubber specimen. As the duration of the surface degradation with UV-CON is prolonged, the contact angle of epoxy resin decreases at the rate of degradation time, while that of silicone rubber was not exchanged. It is assumed that this phenomenon is related to the decrease in hydrophobicity of the surface of the materials. Also, as to epoxy resin, the decrease of hydrophobicity due to surface degradation with UV-CON is greater than that resulting from surface degradation with WOM. The UV radiation produced chalking and crazing on the surface of the insulating materials specimen.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1399-1401
• /
• 2009

In this article, we reported the results of etching polymonochloro-para-xylylene (parylene-C) thin films using inductively coupled plasma and $CF_4/O_2$ gas mixture. The $CF_4$ gas fraction increased up to the approximately 16 %, the polymer etch rate increased in the range of 277 - 373 nm/min. It confirmed that the etch rate of the parylene-C mainly depended on the O radical density in the plasma. Using a contact angle measurement, the contact angle increased with increasing the $CF_4$ fraction. Moreover, the contact angle was highly related a $CF_x$ functional group on parylene films.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 2000

In order to regulate cutting torque in milling, monitoring system should be set to a certain threshold. Radial immersion ratio is an important factor to determine the threshold and should be estimated in process for automatic regulation. In this paper, on-line estimation of the radial immersion ratio using spindle motor current in face milling is presented. When a tooth finishes sweeping, a sudden drop of cutting torque occurs. This torque drop is equal to the cutting torque acting on a single tooth at the swept angle of cut and can be acquired from cutting torque signals. Average cutting torque per revolution can also be calculated from cutting torque signals. The ratio of cutting torque acting on a single tooth at the swept angle of cut to the average cutting torque per revolution is a function of the swept angle of cut and the number of teeth. Using the magnitude of this ratio, the radial immersion ratio is estimated. Identical algorithm is adopted to estimate the immersion ratio based on the spindle motor current measurement. The experiments performed under different cutting conditions show that the radial immersion ratio can be estimated within 10% error range by the proposed method using spindle motor current. Varying immersion ratio is also estimated well using the presented algorithm.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.119-124
• /
• 2003

Despite rapid technological advance and increased automation facilities, many jobs and activities in our living require manual materials handling(MMH). These include wide variety of activities such as moving things, lifting bags. boxes or cartons, etc. Many studies found that handle could affect on maximum acceptable weight of lifting, but there were few studies f3r the effects of work posture and coupling in lifting tote box. This study performed that ten male college students were required to lift a tote box with and without handle for three postures (bending, straight, right angle posture). From the experiment, following results were obtained. (1) MVC reduced maximum 23% by type of handle. (2) MVC was highest in straight posture, but was lowest in right angle posture. (3) As a result of ANOVA, MVC paid attention to posture and coupling. (p<0.01) (4) To all handle types, biceps brachii activity was increased in right angle posture. but reduced in straight posture. (5) To all posture, biceps brachii activity was most lively in no handle. The results of MVC measurement, subjective rating, EMG analysis, statistic analysis showed that maximum acceptable weight of lifting was influenced by type of handle and straight posture was more comfortable than other postures. Based on these results, it was concluded that acceptable weight of lifting has to differ for work posture and coupling.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.479-483
• /
• 2006

Indoor positioning is recently highlighted and various kinds of indoor positioning systems are under developments. Since positioning systems have their own characteristics, proper positioning scheme should be chosen according to the required specifications. Positioning methods are often classified into time-based and angle-based one, and this paper presents the error analysis of these location methods. Because measurement equations of these methods are nonlinear, linearization is usually needed to get the position estimate. In this paper, Gauss-Newton method is used in the linearization. To analyze the position error, we investigate the error ellipse parameters that include eccentricity, rotation angle, and the size of ellipse. Simulation results show that the major axes of error ellipses of TOA and AOA method lie in different quadrants at most region of workspace, especially where the geometry is poor. When the TOA/AOA hybrid scheme is employed, it is found that the error ellipse is reduced to the intersection of ellipses of TOA and AOA method.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.300-308
• /
• 2018

An online estimation method for wireless power transfer (WPT) systems is presented without using any measurement of the secondary side or the load. This parameter estimation method can be applied with a controlling strategy that removes both the receiving terminal controller and the wireless communication. This improves the reliability of the system while reducing its costs and size. In a wireless power transfer system with an LCCL impedance matching circuit under a rectifier load, the actual load value, voltage/current and mutual inductance can be reflected through reflected impedance measuring at the primary side. The proposed method can calculate the phase angle tangent value of the secondary loop circuit impedance via the reflected impedance, which is unrelated to the mutual inductance. Then the load value can be determined based on the relationships between the load value and the secondary loop impedance. After that, the mutual inductance and transfer efficiency can be computed. According to the primary side voltage and current, the load voltage and current can also be detected in real-time. Experiments have verified that high estimation accuracy can be achieved with the proposed method. A single-controller based on the proposed parameter estimation method is established to achieve constant current control over a WPT system.