• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.338.1-338
• /
• 2002

In this report, numerical investigations have demonstrated, that the displacement underneath a moving loading reach a maximum value, if the speed of the load is equal to propagation velocity of the maximum wave. The load speed for which the maximum displacement occurs is called critical speed. The critical speed divides the velocities in a subcritical and a super-critical region. By means of calculations the dynamic behaviour of the slab track-soil is investigated. (omitted)

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.1-7
• /
• 2004

The application of abrasive-assisted high energy water-jet was investigated as a possible new method of cutting wood. In this study the maximum cutting speeds for species of various wood density were determined and water-jet machining characteristics were investigated for sixteen Korean domestic species. The maximum cutting speed ranged from 200 to 750 mm/min. The results indicate that wood density affects machining characteristics such as maximum cutting speed, surface roughness, and kerf width. Roughness of surface generated increased and kerf width decreased as penetration depth increased.

• Journal of the Korean Society for Railway
• /
• v.12 no.5
• /
• pp.670-677
• /
• 2009

This paper is a study of testing on-board signalling equipment in advanced high speed rail at the maximum speed of 400km/h. The on-board signalling equipment in advanced high speed rail provides operating information to the driver when operating at ATC, ATS, and ATP sections, and maintains safety from driver oversight, signalling equipment malfunction, natural disasters and so on. Since the testing train performance of advanced high speed rail at 400km/h must include the function test of on-board signalling equipment, this thesis focuses on the function test of on-board signalling equipment and analyze the necessity of the test at the maximum speed. Finally, it is suggested to change some infrastructure and to use specific test methods to test the train performance at the maximum speed in high speed line ATC section.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.409-412
• /
• 2011

Maximum speed of the train could not exceed over 160km/h with R-bar system in the underground type tunnel structure. By the research to overcome this speed limit, maximum speed has reached up to 200~250km/h recently by new R-bar system. It is under discussion to construct Metro Express Line between Gyonggido and Seoul which requires maximum speed 180km/h~230km/h. New R-bar is an optimal system to achieve the speed improvement in this line. This study shows application of the high speed R-bar system in the underground tunnel section.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2594-2599
• /
• 2011

In Korea, the HEMU-400X(High-speed Electric Multiple Unit-400km/h eXpress) has been developed since 2007 and will be operated over 400km/h in 2013. It is necessary to prepare test-bed section in Honam high-speed railroad to take the maxim running speed test for the HEMU-400X developed. In order to determine proper test-bed sections for the maximum speed of 400km/h, TPS(Train Performance Simulation) program with the data of train model, running resistance, traction power and braking capacity was used to analyze the train performances such as locations, speeds and power consumptions by times. In this study, the specifications of the HEMU-400X project and the route conditions of the Honam high-speed railroad under construction were utilized for the TPS program to determine the optimal test-bed sections for the maximum speed of 400km/h.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.66-72
• /
• 1999

It is necessary to discuss lightening engine parts and reducing the friction of sliding parts to improve fuel consumption and combustion stability at idling condition. Lean best torque combustion which produce maximum power at a lean air-fuel ratio is effective for the reduction of exhaust gas emission and the improvement of fuel consumption. Accordingly, this study deals with the expansion of lean combustible limitation, the combustion stability and the reduction of idle speed through the analysis of combustion characteristics on the base of the control technique of precise air-fuel ratio because it does not need to maximum power at idling condition. The idle speed is increased proportional to ISC(Idle Speed Control) duty ratio. On the other hand the idle speed decreased by lean air-fuel ratio. The COV in engine speed is stable within maximum two percent up to 17.6 mixture ratio by the control of ISC duty ratio.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.3
• /
• pp.105-115
• /
• 2006

The purpose of this study is to elucidate the mechanical characteristics of lower extremity joint movements at different walking speeds in obese people and suggest the very suitable exercise for obese person's own body weight and basic data for clinical application leading to medical treatment of obesity. This experimental subjects are all males between the ages of 20 and 30, who are classified into two groups according to Body Mass Index(BMI): one group is 15 people with normal body weight and the other 15 obese people. Walking speed is analysed at 3 different speeds ($1.5^m/s$, $1.8^m/s$, $2.1^m/s$) which is increased by $0.3^m/s$ from the standard speed of $1.5^m/s$. We calculated joint moments of lower extremity during stance phase through video recording and platform force measurement.Two-way ANOVA(Analysis of Variance, Mix) is applied to get the difference of moments according to walking speeds between normal and obese groups. Pearson's Correlation Analysis is applied to look into correlation between walking speeds and joint moments in both groups. Significance level of each experiment is set as ${\alpha}=.05$. As walking speed increases maximum ankle plantar flexion moment in the stance phase is smaller in obese group than in normal group, which is suggestive of weak toe push-off during terminal stance in obese group, and the highest maximum ankle plantar flexion moment in obese group during the middle speed walking($1.8^m/s.$). Maximum ankle dorsal flexion moment in obese group is relatively higher than in normal group and this is regarded as a kind of compensatory mechanism to decrease the impact on ankle when heel contacts the floor. Maximum knee flexion and extension moments are both higher in normal group with an increase tendency proportional to walking speed and maximum hip flexion and extension moments higher in obese group. In summary, maximum ankle plantar flexion moment between groups(p<.025), maximum knee moment not in flexion but in extension(p<.001) within each group according to increasing walking speed, and maximum hip flexion and extension moment(p<.001 and p<.004, respectively according to increasing walking speed are statistically significant but knee and hip moments between groups are not. Pearson correlation are different: high correlation coefficients in maximum knee flexion and extension moments, in maximum hip extension moment but not hip flexion, and in maximum ankle dorsal flexion moment but not ankle plantar flexion, in each group. We suspect that equilibrium imbalance develops when the subject increases walking speed and the time is around which he takes his foot off the floor.

• Journal of the Korean Society for Railway
• /
• v.6 no.4
• /
• pp.246-251
• /
• 2003

A quantitative analysis on the amounts of cant and lateral displacement of gravitational center due to the introduction of high-speed tilting car was carried out, based on the current alignment of the conventional line. In addition, the maximum allowable speed in curve and the level of improvement in maximum speed of tilting car were evaluated through the comparison with the maximum speed of locomotive. It was found that the tilting car produces an equivalent amount of cant, which corresponds to 47.5 % of current actual cant. This effect could be explained by the fact that 1.34 m, which is the height of gravitational center of tilting car from the rail level, is much lower than that of locomotive and thus guarantees much higher level of safety in curve. The equivalent amount of cant due to the lateral displacement of gravitational center followed by tilting in curve was 2.4 mm. It was small but not enough to be neglected and must be included in calculating the maximum speed in curve. It could be concluded that the 15 % speed-up of the conventional line is reasonable under the current condition of alignment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.383-388
• /
• 2020

This study aimed to identify the influence of the power components of the ammunition vehicle on the maximum speed. The maximum speeds of the engine and transmission changes were 3% and 1.7%, respectively. In the case of strong tension based on the track tension, the decrease was 4.6%. A 1.5% increase was obtained when the tension was weak. An examination of the maximum speed by dividing the track tension into six sections revealed the maximum speed to be highest when it was maintained below the middle. Experiments were performed by varying the orbital tension on both sides of the equipment. The maximum speed of the machine was affected by a large part of the tension. The maximum speed test was conducted by adjusting the tension at the driving test site. The results showed that when the tension was strong, the speed was 16.7% higher than the standard requirement. The speed was 28.3% at low tension. The influence of the maximum speed on the track tension was confirmed; the effect was greater than replacing the large parts.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.1-6
• /
• 2001

An analytical thermal model of HESG(higt efficiency speed grinding) is presented, in which the heat flux to workpiece in grinding zone is modeled as time dependent and moves along a slope decided by contact chord(approximation of con-tact arc). By matching the maximum surface temperature of workpiece derived from this model to the maximum surface temperature of grinding wheel composite as done in Lavins simple thermal model, the relation of maximum surface tem-perature and energy partition of workpiece to grinding speed is obtained. In high speed grinding, as wheel speed increases, energy partition decreases with no regard to table speed.