• Journal of the Korean Institute of Gas
• /
• v.14 no.5
• /
• pp.7-12
• /
• 2010

This paper presents FE analysis on the stress and displacement behavior safeties of dome roof structures for a LNG outer tank, which is constructed by sets of H beams and reinforced concrete. The excitation force of 0.2g is applied at the center of the bottom concrete structure of an outer tank. The computed FEM results indicated that the maximum von Mises stress was shown at the edge of dome roof structure and the maximum displacement was produced at the center of dome roof. The results showed that the concentrated stress and displacement were steadily increased for an increased number of H beams. This means that the number of H beams does not critically affect to the safety of the dome roof structure because the stiffness of a reinforced concrete structure is much higher than that of H beams. Thus, the number of H beams may be restricted under 60 due to a dead weight of H beams for 0.2g excitation force.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1507-1514
• /
• 2016

Full-image guided filter reflects all pixels of image in filtering by using weight propagation and two-pass model, whereas the existing guide filter is processed based on the kernel window. Therefore the computational complexity can be improved while maintaining characteristics of guide filter, such as edge-preserving, smoothing, and so on. In this paper, we propose an efficient VLSI architecture for the full-image guided filter by analyzing the data dependency, the data frequency and the PSNR analysis of the image in order to achieve enough speed for various applications such as stereo vision, real-time systems, etc. In addition, the proposed efficient scheduling enables the realtime process by minimizing the idle period in weight computation. The proposed VLSI architecture shows 214MHz of maximum operating frequency (image size: 384*288, 965 fps) and 76K of gates (internal memory excluded).

• Coupled systems mechanics
• /
• v.8 no.4
• /
• pp.315-338
• /
• 2019

The numerical investigations have been carried out on reinforced concrete slab against blast loading to demonstrate the accuracy and effectiveness of the finite element based numerical models using commercial package ABAQUS. The response of reinforced concrete slab have been studied against the influence of weight of TNT, standoff distance, boundary conditions, influence of air blast and surface blast. The results thus obtained from simulations were compared with the experiments available in literature. The inelastic behavior of concrete and steel reinforcement bar has been incorporated through concrete damage plasticity model and Johnson-cook models available in ABAQUS were presented. The predicted results through numerical simulations of the present study were found in close agreement with the experimental results. The damage mechanism and stress response of target were assessed based on the intensity of deformations, impulse velocity, von-Mises stresses and damage index in concrete. The results indicate that the standoff distance has great influence on the survivability of RC slab against blast loading. It is concluded that the velocity of impulse wave was found to be decreased from 17 to 11 m/s when the mass of TNT is reduced from 12 to 6 kg. It is observed that the maximum stress in the concrete was found to be in the range of 15 to $20N/mm^2$ and is almost constant for given charge weight. The slab with two short edge discontinuous end condition was found better and it may be utilised in designing important structures. Also it is observed that the deflection in slab by air blast was found decreased by 60% as compared to surface blast.

• Journal of the Korean Institute of Gas
• /
• v.18 no.6
• /
• pp.27-31
• /
• 2014

This paper presents a study on the strength safety of the weak parts at Part 1, Part 2 and Part 3 in the valve structure for LPG cylinder by using the finite element method. The maximum Von Mises stress of 27.5MPa was occurred at the corner edge of a valve Part 1 for the valve thickness of 1.5mm and LPG pressure of 3.5MPa. And the maximum Von Mises stresses for the valve thickness of 1.5mm and LPG pressure of 3.5MPa were 41.5MPa at Part 2 and 46.5MPa at Part 3. The FEM computed results show that the maximum Von Mises stresses at Part 1, Part 2 and Part 3 are very low value of 9.2~15.5% compared with the yield strength of a copper alloy, C3604. This means that the valve thickness for LPG cylinder is so over designed for the conventional valve. Thus, this paper recommends that the thickness at Part 1 and Part 2 is reduced for a light weight of a copper valve. But, the thickness at Part 3 may be better for a thick valve as a conventional valve for high torque strength.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.31 no.1
• /
• pp.66-77
• /
• 2003

The purpose of this study is to propose a standard putting green management program to prepare fast green suitable for international golf tournaments, and to conform whether the reported green speed model can be applied to the real field situations. The west course of Lakeside Country Club was selected for the case study. This study was initiated on August 1st, 2001 and continued through October 4th, 2001. The results are summarized as follows: 1. Following the long-term schedule, 'penncross' creeping bentgrass turf was mowed at 5.0mm(37days), 4.5mm(8days), 4.0mm(4days), 3.5mm(2days), 3.2mm(2days), 3.0mm(2days), 2.8mm(2days) and the mowing direction was changed daily. Variation of mowing height was reduced to a minimum range. Core aerification with deep tines was applied 19 days prior to the first practice round. Dry sand maintenance was top-dressed 2 times at 1.5mm/$m^2$ on the 17th day and 1.0mm/$m^2$ on the 10th day. Minimum irrigation was applied to keep the turf alive. During the tournament preparation week, dew on the putting greens was removed by using a sponge roller. Following the dew removal, the greens were cut once each morning at a height of 2.8mm. The mower used was the 21 inch working behind mower equipped with a tournament bedknife and 11 reel blades. Following the mowing, the peens were rolled with a light-weight roller in one direction in the morning. Rolling was used as a finishing technique to ensure that the surface was as smooth as possible, and to provide true ball roll and maximum green speed. In conclusion these management practices satisfied the daily green stimpmeter readings required for USGA championship play. 2. During the period of tournament preparation, no damage was observed on the green, but scalping in green edge appeared in about 0.39% of the total area of 18 greens in the west course.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.4
• /
• pp.316-328
• /
• 2021

In this study, the leaf Na content prediction model for spring potato was established using 400-1000 nm hyperspectral sensor to develop the multispectral sensor for the salinity monitoring in reclaimed land. The irrigation conditions were standard, drought, and salinity (2, 4, 8 dS/m), and the irrigation amount was calculated based on the amount of evaporation. The leaves' Na contents were measured 1st and 2nd weeks after starting irrigation in the vegetative, tuber formative, and tuber growing periods, respectively. The reflectance of the leaves was converted from 5 nm to 10 nm, 25 nm, and 50 nm of FWHM (full width at half maximum) based on the 10 nm wavelength intervals. Using the variance importance in projections of partial least square regression(PLSR-VIP), ten band ratios were selected as the variables to predict salinity damage levels with Na content of spring potato leaves. The MLR(Multiple linear regression) models were estimated by removing the band ratios one by one in the order of the lowest weight among the ten band ratios. The performance of models was compared by not only R2, MAPE but also the number of band ratios, optimal FWHM to develop the compact multispectral sensor. It was an advantage to use 25 nm of FWHM to predict the amount of Na in leaves for spring potatoes during the 1st and 2nd weeks vegetative and tuber formative periods and 2 weeks tuber growing periods. The selected bandpass filters were 15 bands and mainly in red and red-edge regions such as 430/440, 490/500, 500/510, 550/560, 570/580, 590/600, 640/650, 650/660, 670/680, 680/690, 690/700, 700/710, 710/720, 720/730, 730/740 nm.

• Journal of Biomedical Engineering Research
• /
• v.23 no.3
• /
• pp.253-261
• /
• 2002

A spatially adaptive falter was formulated to imrove PET image qualify and the Performance of the filter was evaluated using simulation and phantom and human PET studies. In the proposed filter. if a pixel was identified as the edge Pixel, the Pixel value was Preserved. Otherwise a Pixel was replaced by the mean of the pixel values weighted by 2:7: 2. A Pixel was identified as the edge Pixel. if it satisfies the following conditions : the number of ADs (absolute difference between center and neighborhood pixels) which is smaller than THl (($pix_max{\times}0.1/log_2(NPM)$, NPM : mean of 6 neighborhood pixels excluding minimum and maximum) is 8-k and the number of ADs which is lager than TH2 ($NPM{\times}0.1$) is k. where k : 2, 3, …, 6. The results of this study demonstrate the superior performance of the Proposed titter compared to Gaussian fitter, weight median filter and subset averaged median filter. The proposed tittering method is simple but effective in increasing uniformity and contrast with minimal degradation of spatial resolution of PET images and thus. is expected to Provide improved diagnositc quality PET images .

• Journal of Korean Society of Forest Science
• /
• v.78 no.3
• /
• pp.314-322
• /
• 1989

For the improvement of nursery condition and the study of eco-physiological characteristics of Pinus koraiensis(2-2) seedlings, the primary productivity was investigated and the growth characteristics and their correlationship were analyzed from May to September in 1987. Seedlings used in this study were grown at the nursery of Experimental Forestry of Kyung Hee Univ. The installation of experimental plots were divided into control plot (100%), 63%, 37% and 19% relative light intensity, and each relative light intensity plots were split into $15{\times}15/m^2$, $12{\times}12/m^2$, $9{\times}9/m^2$ and $6{\times}6/m^2$ plnting density by randomized black design method. To take into account the edge effect of plant population, material were selected from each plot by random sampling at 30 days interval. Each sampled material was divided into leaf and stem drived in a drying oven at the temperature of $85^{\circ}C$ until it had constant weight and weighed. and leaf area was surveyed. Growth analysis for RGR and NAR was done by Blackman method and correlation coefficient were investigated between RGR and NAR by analyzing the dry matter production and growth characteristics of the material, cultivated on the experimental nursery under the condition of different treatment the obtained result were as follows : 1. The increasing rate of dry matter was similar at early stage of growth, but not at late stage. 2. Leaf area growth was the maximum value at 63% relative light intensity and the minimum at 19% RLI 3. The value of RGR was the highest on June under $6{\times}6/m^2$ planting density in 63% relative light intensity, the lowest on September under $12{\times}12/m^2$ of 19% relative light intensity. 4. The change NAR decreased in early stage of growth, while it increased on August and September, The value of RGR on June under $6{\times}6/m^2$ planting density in 100 light intensity was the highest, and on September under $12{\times}12/m^2$ planting density in 19% relative light intensity was the lowest. 5. Regression and correlation between RGR and NAR showed significantly positive.