• Journal of the Korean Wood Science and Technology
• /
• 제24권4호
• /
• pp.87-92
• /
• 1996

When cutting 2.0cm-thick red oak and hard maple with an air-jet-assisted carbon-dioxide laser of 2kW output power, maximum feed speed at the point of full penetration of the beam decreased with increasing the angle between grain and cutting direction. Feed speed averaged 3.75 and 3.38 meters per minute for red oak and hard maple, respectively. Gray-level of laser-cut surfaces were analyzed by image analysis system. The highest gray level of laser-cut surface was obtained when red oak was cut parallel to grain by laser. Surface profiler was used to scan the sawn and laser-cut surfaces. Center line average roughnesses of laser-cut surfaces were higher than those of sawn surfaces. Scanning electron micrographs showed the cell walls which were melted by laser.

• Corrosion Science and Technology
• /
• 제9권1호
• /
• pp.34-38
• /
• 2010

Electrochemical study on cut edge corrosion of prepainted Zn coated (GI) and 55%Al-Zn coated (GL) steels has been performed in wet-dry cyclic conditions. Maximum width of delaminated polymer coating from the cut edge for GI and GL specimens was evaluated under wet-dry cyclic conditions. The cyclic tests were carried out for 1000 h by changing of relative humidity, where the salt of NaCl was deposited on the specimen every 48 h. The cut edge corrosion test under NaCl deposit indicated that the delamination of the GL specimen progresses at a higher rate than the GI. The electrochemical corrosion monitoring was also performed under condition of alternate exposure to immersion in NaCl solution and drying at 60%RH and $25^{\circ}C$. On the basis of the results of the delamination tests and electrochemical measurements, the mechanism of cut edge corrosion for GI and GL were discussed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.273-280
• /
• 2001

In order to evaluate the stability of railway cut-slope under rainfall, explanatory variables and subordinate variables were selected for multivariate analysis. Furthermore the site which had occurred failure due to rainfall was investigated, and by executing multivariate analysis for 121 cases, critical rainfall was defined by the case that had high value of correlation factor. The 0.3 square value of maximum hourly rainfall during 24 hours before failure caused the collapse of railway cut-slope and could be used to estimate the stability of railway cut-slope. From the result of application to a collapse example, the evaluaton method by critical rainfall curve is satisfactory.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.188-191
• /
• 2001

Generally, main factors of tool damage are cutting speed, feed rate and depth of cut. The increase of those factors can cause tool breakage or worsen product quality such as machining accuracy deterioration. Those three factors are concerned with cutting force. Cutting force reaches at its maximum value when cutter blade cuts away the object directly, and it is the time when tool damages are at high probability. In this study, we detect the maximum cutting force affecting tool damage and control the maximum cutting force based on the measured peak force.

• 원예과학기술지
• /
• 제31권5호
• /
• pp.538-543
• /
• 2013

여름철 절화 장미 재배 시 고온으로 인한 품질저하를 방지할 목적으로 분무기를 설치하여 기온의 변화와 절화 장미의 품질 및 병충해 발생 정도를 조사하였다. 그 결과, 분무처리 횟수가 증가할수록 일일 최고 온도가 떨어지는 효과가 있었으며, 5분 간격으로 10초간 처리했을 때 최고온도를 $6^{\circ}C$ 정도까지 떨어뜨리는 효과가 인정되었다. 그러나 이러한 온도저하 효과는 일일 최고온도가 $40^{\circ}C$ 이상이 되었을 때만 나타났다. 또한 분무처리는 장미의 초장과 생체중을 10-20%정도 촉진시키는 효과가 인정되었다. 다만, 분무처리에 의해 기형화 발생이 많아지고 절화수명이 대조구에 비해 오히려 짧아지는 등, 절화품질에는 부정적으로 작용하였다. 또한 파밤나방유충이나 깍지벌레와 같은 해충의 발생이 많아지는 부작용도 있었다. 따라서 여름 고온 시 온도저하 목적으로 분무를 사용하고자 할 때에는 $40^{\circ}C$ 이상의 고온 시에만 사용하는 것이 좋고, 해충의 발생이 심해질 수 있으므로 예방을 철저히 할 필요가 있다고 사료되었다.

• 한국광학회지
• /
• 제30권1호
• /
• pp.8-14
• /
• 2019

본 논문에서는 추가적인 광학부품 및 조립공정 없이 차량용 헤드램프의 cut-off line에서 발생하는 색수차를 보정하는 방법과 이를 평가하는 방법을 제안한다. 기하학적인 방법으로 색수차를 보정하기 위해 비구면 프로젝션 렌즈의 볼록면에 tilt를 적용하여 파장별 최대 출사각도의 차이를 줄였으며, 색수차를 평가하기 위한 위치와 광도를 정하고 색 좌표를 통해 색수차 기준을 제시하였다. 이러한 기하학적인 방법을 이용하여 설계된 자동차용 헤드램프를 평가한 결과 cut-off line의 색수차가 상당히 감소되었음을 확인할 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 사면안정학술발표회
• /
• pp.65-81
• /
• 2003

During the last few decades in Korea, the development of hillside or mountain areas has rapidly increased for infrastructure construction such as railroads, highways and housing. Many landslides have occurred during these constructions. Also, the amount and scale of damage caused by landslides have increased every year. In the case of Far East Asia including Korea, the damage of landslides is consequently reported during the wet season. In this paper, the effect of stabilizing piles on slope stability is checked and the behavior of slope soil and piles are observed throughout the year by field measurements in the large-scale cut slopes. In particular a large-scale cut slope situated on the construction site for the express highway in Donghae, Korea. First of all, The behavior of the slope soil was measured by inclinometers during slope modification. Landslides occurred in this area due to the soil cutting for slope modification. The horizontal deformations of slope soil gradually increased and rapidly decreased at depth of sliding surface indicating that the depth of sliding surface below the ground surface can be predicted. On the basis of being able to predict the depth of the sliding surface, stabilizing piles were designed and constructed in this slope. To ensure the stability of the reinforced slope using stabilizing piles, an instrumentation system was installed. The maximum deflection of piles is measured at the pile head and it is noted that the piles deform like deflection on a cantilever beam. The maximum bending stress of piles is measured at the soil layer. The pile above the soil layer is subjected to lateral earth pressure due to driving force of the slope, while pile below soil layer is subjected to subgrade reaction against pile deflection. As a result of research, the effect and applicability of stabilizing piles in large-scale cut slopes could be confirmed sufficiently.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.670-675
• /
• 2006

The purpose of this study is the infiltration characteristics of soil cut-slope by the repetition & concentration rainfall. The maximum rainfall concentrate from June until September which is a rainy season in our country Stability analysis of soil cut-slopes has been conducted by limit equilibrium method on Seep/w and finite element method on Slope/w.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.15-19
• /
• 2014

In this study, for 6-20 MeV electron beam energy occurring in a linear accelerator, the authors attempted to investigate the relation between the effective source-skin distance and the relation between the radiation field and the effective source-skin distance. The equipment used included a 6-20 MeV electron beam from a linear accelerator, and the distance was measured by a ionization chamber targeting the solid phantom. The measurement method for the effective source-skin distance according to the size of the radiation field changes the source-skin distance (100, 105, 110, 115 cm) for the electron beam energy (6, 9, 12, 16, 20 MeV). The effective source-skin distance was measured using the method proposed by Faiz Khan, measuring the dose according to each radiation field ($6{\times}6$, $10{\times}10$, $15{\times}150$, $20{\times}20cm^2$) at the maximum dose depth (1.3, 2.05, 2.7, 2.45, 1.8 cm, respectively) of each energy. In addition, the effective source-skin distance when cut-out blocks ($6{\times}6$, $10{\times}10$, $15{\times}15cm^2$) were used and the effective source-skin distance when they were not used, was measured and compared. The research results showed that the effective source-skin distance was increased according to the increase of the radiation field at the same amount of energy. In addition, the minimum distance was 60.4 cm when the 6 MeV electron beams were used with $6{\times}6$ cut-out blocks and the maximum distance was 87.2 cm when the 6 MeV electron beams were used with $20{\times}20$ cut-out blocks; thus, the largest difference between both of these was 26.8 cm. When comparing the before and after the using the $6{\times}6$ cut-out block, the difference between both was 8.2 cm in 6 MeV electron beam energy and was 2.1 cm in 20 MeV. Thus, the results showed that the difference was reduced according to an increase in the energy. In addition, in the comparative experiments performed by changing the size of the cut-out block at 6 MeV, the results showed that the source-skin distance was 8.2 cm when the size of the cut-out block was $6{\times}6$, 2.5 cm when the size of the cut-out block was $10{\times}10$, and 21.4 cm when the size of the cut-out block $15{\times}15$. In conclusion, it is recommended that the actual measurement is used for each energy and radiation field in the clinical dose measurement and for the measurement of the effective source-skin distance using cut-out blocks.

• 핵의학기술
• /
• 제14권1호
• /
• pp.18-23
• /
• 2010

최근 PET/CT영상의 발달로 종양의 진단 및 평가를 통해 임상에 많은 도움을 주고 있다. 특히 PET와 CT를 융합한 Fusion PET/CT영상이나 2차원 PET영상을 3차원 영상으로 재구성한 최대강도영상(Maximum Intensity Projection)은 전체적인 병변을 한눈에 시각화하는 데 유용하게 쓰이고 있다. 하지만 Fusion & MIP 3D 재구성 영상에서 $^{18}F$-FDG의 생리적 배출로 소변이나 요루주머니에 의한 열소가 나타나 병변이 겹쳐져 육안적으로 병변을 구별하는 데 어려움이 있다. 본 연구에서는 소변에 의해 나타나는 열소 부위를 제거하여 병변의 분별력을 향상하고자 한다. 2008년 9월부터 2009년 3월까지 내원한 환자 중 PET/CT 검사에서 자궁, 방광, 직장 부위의 질환으로 잔존하는 소변량이 많은 환자들을 대상으로 하였다. 분석장비는 GE사의 Advantage Workstation AW4.3 05 버전 Volume Viewer 프로그램을 사용하였다. 분석 방법은 2D PET axial volume 영상에서 제거하고자 하는 region에 ROI를 설정하여 Cut Outside를 선택한 후 coronal volume 영상도 동일한 방법을 적용한다. 다음으로 3D Tools의 threshold 값을 지정하고, Advanced Processing에서 Subtraction을 선택하여 차집합 방식으로 소변 영상만을 소거한다. 이렇게 Region Cut Subtraction이 된 2D PET영상과 CT영상으로 Fusion영상과 MIP영상을 만들어 Region Cut Subtraction하지 않은 영상과 비교한다. Fusion & MIP 3D 재구성 영상에서 Advantage Workstation AW4.3 05버전의 Region Cut Subtraction으로 환자의 소변이나 요루주머니에 의한 열소 부위를 제거할 수 있었다. Region Cut Definition을 사용한 영상에서 그렇지 않은 영상보다 소변 섭취 때문에 구별이 어렵던 병변과의 경계가 보다 명확하게 재구성되었다. 영상을 재구성하는 과정에서 Region Cut Subtraction을 사용하여 열소 부위를 제거한다면 기존에 사용하던 단순 역치범위 설정에 의한 영상 소거법보다 우수한 진단적 정보를 제공할 것이다. 특히 방광, 자궁, 직장 부위 질환의 경우, 판독의와 임상의에게 판독에 보다 유용한 영상 정보를 제공하고, 영상의 질적 향상에 도움이 될 것이라 판단된다.