• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 춘계학술대회 논문집
• /
• pp.235-240
• /
• 2007

A large power fuel cell generation system needs a parallel operation of de-de boost converter. Therefore, this paper proposed parallel operation algorithms of de-de boost converters for the large scale fuel cell generation system of 250[kW] and the operating principle along with the control method in detail. This paper uses a maximum current sharing method as a parallel operation method and also the phase shift full bridge de-de converter as a de-de boost converter. Simulation and experimental results on two prototype converter modules of 500W show that the parallel operation method can be applied to the 250[kW] power converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술대회 논문집 전문대학교육위원
• /
• pp.70-74
• /
• 2003

The buck-boost converter is employed as the variable output PFC power stage. From the loss analysis, this topology has a high efficiency from light load to heavy load. A modified input current sensing scheme is presented to overcome the problem of the insufficient phase margin for the PFC circuit near the maximum output voltage. The variable output PFC circuit has a good performance in the wide output voltage range, under both the Boost mode when the output voltage is high and the Buck+Boost mode when the output voltage is low.

• 전기학회논문지
• /
• 제59권10호
• /
• pp.1845-1849
• /
• 2010

We have proposed and fabricated a Buck-Boost DC to DC Converter for Thermoelectric generator (TEG) with constant output voltage suitable for battery chargers or constant voltage supplies in the range of several watt. The experimental and simulation results have shown that the proposed method allows stable operation with maximum 86% power transfer efficiency. The proposed circuit has a merit in cost and miniaturization of a system compared to conventional MPPT algorithms, because the proposed method adopts only analog circuit without DSP or micro controller unit for calculating peak power point by iterative methods.

• 조명전기설비학회논문지
• /
• 제28권8호
• /
• pp.54-61
• /
• 2014

This paper proposes a boost/flux-weakening controller (BFWC) for wide speed operation range having engine and interior permanent magnet synchronous generator (IPMSG) for special equipment vehicle. The proposed BFWC exploits direct torque/flux control (DTFC) scheme based on space vector modulation method to control the constant DC voltage output within the entire speed operation range of engine. And, to improve the response characteristics of maximum torque per ampere (MTPA) operation and flux-weakening operation, the MTPA and flux-weakening feed-forward controllers are applied. To estimate feasibility and usefulness of the proposed controller, the simulation and experimental results are compared.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.793-797
• /
• 2003

Switching PFC converters are widely used not only to comply the power quality specification but also for maximum efficiency. However switching PFC converters generate serious electromagnetic interference (EMI). In this paper to solve this problem, we applied the APW(Anti Phase Winding) and RPWM(Ran-dom PWM) technique to PFC boost converter and obtained satisfactory results. Simulation and experimental results show the improved harmonic and reduced EMI effect in air-conditioner system.

• 오토저널
• /
• 제11권2호
• /
• pp.41-54
• /
• 1989

In this study, steady state heat conduction problems of the cylinder block of turbocharged gasoline engine were solved by the boundary element method. Surface of the cylinder block was divided by the triangular cells with constant potential. Temperature distribution, effective heat transfer coefficient of the cylinder block were investigated with variation of equivalence ratio, engine speed and boost pressure. The results show that maximum temperature of cylinder block increase rapidly with increasing engine speed and boost pressure. The monolithic structure of cylinder block results in sever inhomogeneity of inner wall temperature at the high engine speed and boost pressure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1498-1500
• /
• 2004

A novel technique for efficiently extracting maximum power from PV panels is proposed, consisting of a modified buck-boost converter, witch is controlled by a DSP. A variation of the proposed MPPT technique is directly use the modified buck-boost converter current reference as a control parameter. Also 4 parallel boost converters have division of load. A theoretical analysis of the proposed converter is performed and compared with experimental results obtained from a 1k[W] prototype solar panel under a controlled experimental setup.

• 전기학회논문지
• /
• 제60권4호
• /
• pp.781-788
• /
• 2011

This paper proposes a boost-input self-driven active clamp ZVS converter eliminating the extra dirve circuit for the active clamp switch. The converter used the auxiliary winding of the transformer to drive the active clamp switch and to achieve asymmetrical duty control. This paper presents the operation principle and the analyzed results of dynamic characteristics including steady state characteristics of the converter proposed. The experimental results were used to verify the theoretical predictions. A 300W (15V/20A) prototype converter that only exhibited 2-turn winding number in the auxiliary winding was sufficient to drive the active clamp switch on the input voltage of 80V. Finally, the maximum efficiency of 91.2% was achieved for the prototype converter and the proposed converter had stable closed loop characteristic with phase margin $55^{\circ}$.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.214-217
• /
• 2003

The connectorless power supply system on that multi-contact causes confidence when the wiring reconstructed in the rear. As you see above, contact points between sets and indoor space cause inferior function of audio frequency so it needs to be eliminated. This paper explains the structure of connectorless power supply to supply the system with power crossing the air gap in the part of inductively in the connectorless power supply of both magnetic and electrical model. To get maximum output of electrical load, compensating capacitor compensates to show inter-inductance, lequeage-inductance reducing the track-inductance and access the conditions for resonance. At that time it accesses the maximum electric power. The small change of the value of compensating capacitor causes the changes of maximum electric power. Here the power electronics technology is used not only in the industrial machinery but also in the home appliances so the switching power supply is used to actualize the miniaturization, lightweight, and high efficiency. Generally the condenser input methods are widely used in the rectification circuit of switching power supply, but condenser input method generate great quantity of high frequency components because with this method the current flows in the power input filtering condenser only around value of peak of ac input voltage. To solve these problems, installation of power factor improve circuit on the front of filtering capacitence was considered. Several methods were suggested regarding, but the active filter method which makes smalliging and highly power factor possible are the produce main stream. IC for power factor improvement can be utilized by CMOS process proposing low power consumption. When the high power factor is considered seriously in the power factor improvement circuit, active filter method is selected. In the active filter method, the boost converter is used. Regarding this ·the boost converter is needed.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 추계학술대회
• /
• pp.412-415
• /
• 2015

본 논문에서는 진동에너지 수확을 위한 MPPT(Maximum Power Point Tracking) 제어 CMOS 인터페이스 회로를 설계하였다. 제안된 회로는 AC-DC 변환기, MPPT 제어회로, DC-DC 부스트 변환기, 그리고 PMU(Power Management Unit)로 구성된다. AC-DC 변환기는 진동소자(PZT)에서 출력되는 AC 신호를 DC 신호로 변환해주는 역할을 하며, MPPT 제어회로는 진동소자로부터 최대전력을 수확하여 효율을 높이는 역할을 한다. DC-DC 부스트 변환기는 AC-DC 변환기에서 공급된 에너지를 원하는 값으로 승압 및 안정화 시키는 역할을 하며 PMU를 통해 부하로 에너지를 전달한다. AC-DC 변환기는 효율 특성이 좋은 능동 다이오드를 이용한 전파정류기를 사용하였으며, DC-DC 부스트 변환기는 제어 회로가 간단한 쇼트키 다이오드를 사용한 구조를 사용하였다. 제안된 회로는 0.35um CMOS 공정으로 설계되었으며, 설계된 칩의 면적은 $950um{\times}920um$이다.