• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1569-1579
• /
• 2021

This study aims to provide microstructural characterization for the matrix graphite which molten salt reactors (MSRs) use, and improve resistance to molten salt infiltration of the matrix graphite for fuel elements. Mesocarbon microbeads (MCMB) densified matrix graphite A3-3 (MDG) was prepared by a quasi-isostatic pressure process. After densification by MCMBs with average particle sizes of 2, 10, and 16 ㎛, the pore diameter of A3-3 decreased from 924 nm to 484 nm, 532 nm, and 778 nm, respectively. Through scanning electron microscopy, the cross-section energy spectrum and time-of-flight secondary ion mass spectrometry, resistance levels of the matrix graphite to molten salt infiltration were analyzed. The results demonstrate that adding a certain proportion of MCMB powders can improve the anti-infiltration ability of A3-3. Meanwhile, the closer the particle size of MCMB is to the pore diameter of A3-3, the smaller the average pore diameter of MDG and the greater the densification. As a matrix graphite of fuel elements in MSR was involved, the thermal and mechanical properties of matrix graphite MDG were also studied. When densified by the MCMB matrix graphite, MDGs can meet the molten salt anti-infiltration requirements for MSR operation.

• 한국정밀공학회지
• /
• 제20권1호
• /
• pp.214-221
• /
• 2003

In this study, based on the effect of the interaction of fracture mechanics by graphite and fatigue limit phenomena of the microscopic observation various matrix structure, spheroidal ratio, size of graphite and distribution etc. parameters containd with Ductile Cast Iron. Therefore, in this study, different ferrite-pearlite matrix structure and spheroidal ratio of graphite of 70%, 80% and 90%, GCD40, GCD45-1 and GCD45-2 series and three different ferrite-pearlite matrix structure, GCD 45-3, GCD 50, GCD 60 series, all of which contain more than 90% spheroidal ratio of graphite, were used to obtain the correlation between mean size of spheroidal graphite and fatigue strength. (1) 73% pearlite structure had the highest fatigue limitation while 36% pearlite structure had the lowest fatigue limitation among ferrite-pearlite matrix. the increase in spheroidal ratio with increasing fatigue limitation, 90% had the highest, 14.3% increasing more then 10%, distribution range of fatigue life was small in same stress level. (2) (equation omitted) of graphite can be used to predict fatigue limit of Ductile Cast Iron. The Statistical distribution of extreme values of (equation omitted) may be used as a guideline for the control of inclusion size in the steelmaking processes.

• 한국생산제조학회지
• /
• 제8권5호
• /
• pp.36-41
• /
• 1999

Although the problems of defects and nonmetallic inclusion in metal fatigue are very complicated it is particularly important to view these problems from the perspective that defects and inclusions are virtually equivalent to small cracks. This concept will help us to understand various fatigue phenomena caused by graphite of Ductile cast iron. Therefore in this study different ferrite-pearlite matrix structure and pheroidal ratio of graphite of 70%, 80% and 90% GCD40 , GCD45-2 series have been carried out rotary bending fatigue test estimated the maxi-mum size of graphite investigated correlation. It was concluded as follows : (1) in ductile cast iron which have various spheroidal ratio of graphite the fatigue limit C series of 90% spheroidal ratio of graphite is the highest. While A series of 70% spheroidal ratio of graphite is the lowest (2) fatigue limit was predicted by vickers hardness(Hv) of matrix {{{{ SQRT {area } }}}} of maximum size graphite inputting Murakami and Endo's formula.

• 한국주조공학회지
• /
• 제3권3호
• /
• pp.174-180
• /
• 1983

The matrix changes and graphite formation in high manganese cast iron (Fe-12Mn-3.5C) are studied with increasing nickel and silicon content. Also, the decomposition of carbides and graphite precipitation are studied by adequate heat treatment.The results obtained in this work are as follows. 1. In high manganese cast iron, fine flakes graphite appeared by adding 5 wt% nickel and A-type flakes graphite can be obtained by adding 7 wt% nickel. 2. Nodular graphite are obtained by graphite spheroidizing treatment with same melt. 3. In high manganese cast iron containing 7 wt% nickel, full austenitic matrix with nodular graphite can be achieved by water quenching after 10 hours' solution heat treatment at $1050^{\circ}C$ in case of containing 2.0 wt% silicon, and 6 hours' at the same temperature in case of containing 2.5 wt% silicon.

• 한국주조공학회지
• /
• 제9권4호
• /
• pp.327-335
• /
• 1989

The matrix structure and the morphology of CV graphite are affected by the addition of many kinds of elements, which are contained in the CV graphite cast iron, additives, fading time and cooling rate. The effects of cooling rate on the matrix structure, the shape of CV graphite, mechanical properties and propagation of ultrasonic wave in hypoeutectic CV graphite cast iron were studied. When the diameters of the samples are 50mm, 35mm and 20mm 1. CV graphite number showed average 17.9% increase and CV graphite length showed 10.3% decrease with decreasing diameter of the samples. 2. The amount of graphite and ferrite showed average 11.2, 4.1 % decrease and the amount of pearlite showed average 15.7% increase. 3. Hardness and tensile strength showed average 3.5%, 11.3% increase and impact strength showed average 1.5% decrease. 4. Ultrasonic wave velocity showed average 1.1% increase.

• 한국주조공학회지
• /
• 제9권4호
• /
• pp.336-344
• /
• 1989

The matrix structure and the morphology of CV graphite are affected by the addition of many kinds of elements, which are contained in the CV graphite cast iron, additives, fading time and cooling rate. The effects of cooling rate on the matrix structure, the shape of CV graphite, mechanical properties and propagation of ultrasonic wave in eutectic CV graphite cast iron were studied. When the diameters of the samples are 50mm, 35mm and 20mm 1. CV graphite number showed average 13.8% increase and CV graphite length showed 12.3% decrease with decreasing diameter of the samples. 2. The amount of graphite and ferrite showed average 10.6, 4.3% decrease and the amount of pearlite showed average 23.4% increase. 3. Hardness and tensile strength showed average 3.2%, 9.5% increase and impact strength showed average 1.3% decrease. 4. Ultrasonic wave velocity showed average 1.1% increase.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.82-87
• /
• 2012

For different ferrite-pearlite matrix structure, contain more than 90% spheroidal ratio of graphite, GCD 45-3, GCD 50, GCD 60 series and 70%, 80%, 90% spheroidal ratio of graphite, GCD 40, GCD 45-1, GCD 45-2 series, this paper has carried out rotary bending fatigue test, estimated maximum and mean size of spheroidal graphite, investigated correlation. It was concluded as follows. (1) Fatigue limit in $10^7$cycles and numbers of spheroidal graphite per 1$mm^2$ was linear relation. (2) projection area of graphite can be used to predict fatigue limit of Ductile Cast Iron. The Statistical distribution of extreme values of projection area of defects may be used as a guideline for the control of inclusion size in the steelmaking processes.

• 한국생산제조학회지
• /
• 제7권5호
• /
• pp.66-71
• /
• 1998

It is required the superior materials for the parts of machines or structures, which could be endurable in severe load and environment. According to advancement of casting technology, nodular graphite cast iron is used as suitable for such condition. But nodular graphite cast iron is scattering of fatigue strength and low reliability. Therefore in this study, the effect of matrix structure and number of nodular graphite on the initiation of fatigue crack and fatigue strength. It was found that the material which has relatively high ferrite volume fraction was more easily cracked than other materials and fatigue limit was low. The material which has not found pinhole on the surface, the crack was initiated in graphite went through ferrite and propagated into through graphite, but separated graphite and ferrite grain boundary and combined with other cracks to fro large one.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.42-47
• /
• 2001

In this study, fatigue limit of ductile cast iron is evaluated based on phenomena of the microscopic observation, such as matrix structure, spheroidal ratio, size of graphite and distribution. Three different ferrite-pearlite matrix structure, GCD 45-), GCD 50, GCD 60 series, all of which contain more than 70% spheroidal ratio of graphite, were used to obtain the correlation between maximum size of graphite and fatigue strength. It was concluded as fellows. (1) In Ductile cast iron of ferrite-pearlite matrix, the fatigue limit of GCD 60 series with 73% pearlite structure was the highest. (2) From observation of the starting point of crack of all specimens, it is noted that the crack initiates, in graphite, goes through ferrite and propagates into pearlite. (3) A good quality of Ductile cast iron used in this experiment can be checked from uniformly distributed graphite. The negligible interaction effect between graphites was verified by microscopic observation and fracture mechanics investigation in surface and interior of the specimen.

• Bulletin of the Korean Chemical Society
• /
• 제21권4호
• /
• pp.401-404
• /
• 2000

Matrix/Surface-assisted laser desorption/ionization (M/SALDI) mass spectrometry of polypropylene glycol and polystyrene, directly deposited on graphite plate, is demonstrated. Graphite plate is effective both as an en-ergy transfer medium and robu st sampling support for LDI of polymers. Mass spectra ofpolymers can be easily obtained due to homogeneous distribution on graphite surface and their ion signals are long-lived by large ef-fective desorption volume enough to investigate M/SALDI process.