• Korean Journal of Metals and Materials
• /
• v.48 no.2
• /
• pp.122-132
• /
• 2010

Higher strength and fracture toughness of reactor pressure vessel steels can be obtained by changing the material specification from that of Mn-Mo-Ni low alloy steel (SA508 Gr.3) to Ni-Mo-Cr low alloy steel (SA508 Gr.4N). However, the operation temperature of the reactor pressure vessel is more than $300^{\circ}C$ and the reactor operates for over 40 years. Therefore, we need to have phase stability in the high temperature range in order to apply the SA508 Gr.4N low alloy steel for a reactor pressure vessel. It is very important to evaluate the temper embrittlement phenomena of SA508 Gr.4N for an RPV application. In this study, we have performed a Charpy impact test and tensile test of SA508 Gr.4N low alloy steel with changing impurity element contents such as Mn and P. And also, the mechanical properties of these low alloy steels after longterm heat treatment ($450^{\circ}C$, 2000hr) are evaluated. Further, evaluation of the temper embrittlement by fracture analysis was carried out. Temper embrittlement occurs in KL4-Ref and KL4-P, which show a decrease of the elongation and a shifting of the transition curve toward high temperature. The reason for the temper embrittlement is the grain boundary segregation of the impurity element P and the alloying element Ni. However, KL4-Ref shows temper embrittlement phenomena despite the same contents of P and Ni compared with SC-KL4. This result may be caused by the Mn contents. In addition, the behavior of embrittlement is not largely affected by the formation of $M_3P$ phosphide or the coarsening of Cr carbides.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.3
• /
• pp.277-286
• /
• 2009

A suitability of a thixotropic grout developed in this study has been examined through laboratory tests on strength, segregation, and viscosity. The thixotropic grout is a mixture of two types of liquid components. The A-liquid component consists of cement, water, and MG-A and the B-liquid component consists of scarlet, water, and MG-B. Unconfined compressive strength of specimens prepared with a prefer mix-proportion satisfied a design criteria for the backfilling of tail voids. A material segregation phenomenon under water condition was not observed in the thixotropic grout whereas it was observed in the existing silica-type grout. In addition, viscosity tests have been rallied out on the thixotropic grout to verify the capability of a long-distance delivery in the field. Both the A-liquid component and the B-liquid component maintained a viscosity of below 2,000 cP for 120 minutes. This experimental result confirms that two liquid components guarantees a long-distance delivery in tile field application.

• Research in Plant Disease
• /
• v.18 no.4
• /
• pp.317-323
• /
• 2012

The study aims to identify the pathogenicity of Phytophthora. capsici isolates in major pepper-producing areas in Korea and the inherit genetic pattern of phytophthora blight resistance by inocula. With five kinds of testing materials including 'Kataguma (Sakata Korea)' peppers, a disease-susceptible material, '#308', a phytophthora blight resistance material, 'CM334', and their $F_1$ and $F_2$, respective isolates of P. capsici obtained from Icheon, Eumseong, Buan, Imsil and Yeongyang regions together with six kinds of peppers' inoculum including PA-159 (KACC No.40482) received from Korean Agricultural Culture Collection were used for inoculation. The disease-susceptible material '#308', the resistant material 'CM334' and the non-segregating generation of $F_1$ represented 4.94-5.00, 1.00-1.07, and 1.01-1.08 phytophthora blight incidence respectively in the group comparison by isolate. This result means that the phytophthora blight resistance was clearly distinguished among testing materials in the group comparison by P. capsici isolate. Moreover, $F_2$ segregating generation showed 1.79-2.31 phytophthora blight incidence which turned out to be identical in the group comparison by the six isolates of P. capsici isolate and with similarity between both the resistant and susceptible materials. Thus, the result proved that using the six isolates of P. capsici tested as inocula was suitable to investigate the phytophthora blight resistance. When it comes to group comparison of $F_2$ segregation generation, however, isolates were divided with PA-159 isolate being the center: a group consisting of isolates from Icheon, Buan, and Imsil and a group consisting of Yeongyang and Eumseong isolates with higher pathogenicity. The expected segregation ratio of the phytophthora blight resistance in $F_2$ generation by isolate was analyzed. PA-159 isolate showed 3:1 or 9:3:3:1, indicating that one to two genes were involved. On the other hand, results also proved that there is an interaction of genes since both Eumseong and Yeongyang isolates showed a segregation ratio of 11:5 while the Icheon isolate represented 12:3:1.

• Journal of the Korea Concrete Institute
• /
• v.24 no.4
• /
• pp.465-472
• /
• 2012

This research aims to find an effective mixing method for controlled low strength material (CLSM) using diverse recycled industrial byproducts. This study is a fundamental research to develop and commercialize a resource-recycling CLMS that can greatly contribute to cost reduction and environmental stress relief. In the past, few studies have been performed on CLSM in Korea. This research is expected to provide fundamental data not only for development and commercialization of the resource-recycling CLSM satisfying required material performances but also serve as a ground breaking study on utilization of recycled material in construction industry and ultimately leading to advanced resource-recycling practices at national level. From the comprehensive analysis of minimum unit quantity for maximum strength and material segregation prevention, it was found that the optimal mixing condition for mixing FSD, RSID and SD material to filler-aggregate ratio (f/a) was approximately 50.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.6 s.177
• /
• pp.1398-1407
• /
• 2000

The structural steels of power plant show the decrease of mechanical properties due to degradation such as temper embrittlement, creep damage and softening during long-term operation at high temper ature. The typical causes of material degradation damage are the creation and coarsening of carbides(M23C6, M6C) and the segregation of impurities(P, Sb and Sn) to grain boundary. It is also well known that material degradation induces the cleavage fracture and increases the ductile-brittle transition temperature of steels. So, it is very important to evaluate degradation damage to secure the reliable and efficient service condition and to prevent brittle failure in service. However, it would not be appropriate to sample a large test piece from in-service components. Therefore, it is necessary to develop a couple of new approaches to the non-destructive estimation technique which may be applicable to assessing the material degradation of the components with not to influence their essential strength. The purpose of this study is to propose and establish a new electrochemical technique for non-destructive evaluation of material degradation damage for Cr-Mo steels which is widely used in the high temperature structural components. And the electrochemical anodic polarization test results are compared with those of semi-nondestructive SP test.

• Journal of Technologic Dentistry
• /
• v.22 no.1
• /
• pp.69-78
• /
• 2000

The microstructure and corrosion behavior of commercially dental casting gold alloys were investigated to clarify the effect of burn-out temperature and cooling rate. In the case of water quenching after casting, only the αphase, which is typical dendritic microstructure of golda alloy, was detected. However, the precipitates along the grain boundary were detected only at the slow cooling rate and they increased inversely proportional to the burn-out temperature. This might be due to the time difference which solute atom could diffuse. EPMA and SEM results also demonstrated that the precipitate should be lamellar structure consisted of Ag rich phase(${\alpha}_1$) and Cu rich phase (${\alpha}_2$). In terms of corrosion, the galvanic coupling was formed due to the difference of composition between precipitates and matrix at the slow cooling rate. In the case of water quenching, the critical current density($i_p$) which indicate the degree of corrosion was lowest at $650^{\circ}C$ and below the burnout temperature, $i_p$ increased with it because of the effect of grain boundary segregation. But above the temperature, $i_p$ increased with it. This may be due to the strain field effect by residual thermal stress.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.657-665
• /
• 2013

The purpose of this study is the basic research of self-compacting concrete using Alkali-Activated Slag (AAS) binder in order to emphasize the durability of structures and facilitate casting the fresh concrete in field. The AAS binder emitted low carbon dioxide ($CO_2$) is eco friendly material of new concept because AAS products not only emit little $CO_2$ during production but also reuse the industrial by-products such as ground granulated blast-furnace slag (GGBS) of the steel mill. Until now, almost of domestic and foreign research are using Ordinary Portland Cement (OPC) for self-compacting concrete, and also, nonexistent research about AAS. The self-compacting concrete must get the performance of flowability, segregation resistance, filling and passing ability. Nine concrete mixes were prepared with the main parameter of unit amount of binder (400, 500, 600 $kg/m^3$) and 3 types of water-binder (W/B) ratio. The results of test were that fresh concretes were satisfied with flowability, segregation resistance, and filling ability of JSCE. But the passing ability was not meet the criteria of EFNARC because of higher viscosity of AAS paste than OPC. This high viscosity of AAS paste enables the manufacturing of self compacting concrete, segregation of which does not occur without the using of viscosity agent. It is necessary that the development of high fluidity AAS binders of higher strength and the study of better passing ability of AAS concrete mixes in order to use self compacting AAS concrete in field.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.11
• /
• pp.683-689
• /
• 2015

For the formation of $N^+$ doping, the antimony ions are mainly used for the fabrication of a BJT (bipolar junction transistor), CMOS (complementary metal oxide semiconductor), FET (field effect transistor) and BiCMOS (bipolar and complementary metal oxide semiconductor) process integration. Antimony is a heavy element and has relatively a low diffusion coefficient in silicon. Therefore, antimony is preferred as a candidate of ultra shallow junction for n type doping instead of arsenic implantation. Three-dimensional (3D) profiles of antimony are also compared one another from different tilt angles and incident energies under same dimensional conditions. The diffusion effect of antimony showed ORD (oxygen retarded diffusion) after thermal oxidation process. The interfacial effect of a $SiO_2/Si$ is influenced antimony diffusion and showed segregation effects during the oxidation process. The surface sputtering effect of antimony must be considered due to its heavy mass in the case of low energy and high dose conditions. The range of antimony implanted in amorphous and crystalline silicon are compared each other and its data and profiles also showed and explained after thermal annealing under inert $N_2$ gas and dry oxidation.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.319-323
• /
• 2001

In significant number of energy-related facilities for like thermal power plant or petro-chemical industry, CrMo steels are widely used energy conversion industries. However, these materials undergo precipitation of carbides or intermetallic compounds into grain boundary and change of internal microstructure such as coarsening of precipitation, decrease of solute elements and impurity segregation under more severe service conditions, which results in deterioration of inherent superior material characteristics. In this study, it was verified experimentally the feasibility of the aging degradation evaluation for degraded 2.25Cr-lMo steel specimens prepared by isothermal aging heat treatment at 63$0^{\circ}C$ by high frequency longitudinal ultrasonic and surface SH wave investigating the change of attenuation coefficient analyzed by spectral analysis. Attenuation coefficient had a tendency to increase as degradation proceeded.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.138-138
• /
• 2008

Ti capping layer를 이용하여 NiGe의 열적 안정성을 향상시키는 연구를 수행하였다. N-type Ge(100) 기판에 30nm 두께의 Ni과 30nm 두께의 Ti capping layer를 E-beam evaporator를 이용하여 증착하고 $300^{\circ}C$에서 $700^{\circ}C$ 까지 30초간 $N_2$ 분위기에서 급속 열처리하여 Ni-Germanide를 형성하였다. XRD의 결과로부터 Ti capping layer 유무에 상관없이, 전 온도 범위에 걸쳐 NiGe 상이 형성된 것을 관찰할 수 있었다. 급속 열처리 온도에 따른 면저항 값을 측정한 경우, $300^{\circ}C$에서 $600^{\circ}C$까지의 열처리 온도 범위에서는 모든 시편들이 비슷한 면저항 값을 보인 반면, 열처리 온도가 $700^{\circ}C$ 이상에서는 Ti capping layer가 있는 시편이 Ti capping layer가 없는 시편보다 낮은 면저항 값을 갖는 것을 확인할 수 있었다. 이는 고온 열처리 시 Ti capping layer에 있는 Ti가 기판 방향으로 확산하여 NiGe grain boundary에 segregation 되고 그로 인하여 NiGe의 grain boundary 움직임을 억제하여 agglomeration 현상을 효과적으로 방지하였기 때문에 나타난 현상으로 사료된다.