• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.96-102
• /
• 2005

Acoustic Emission(AE) technique has been applied to not only material characterization evaluation but also on-line monitoring of the structural integrity. The AE source location technique is very important to identify the source, such as crack, leak detection. Since the AE waveforms obtained from sensors are very difficult to distinguish the defect signals, therefore, it is necessary to consider the signal analysis of the transient wave-form. In this study, we have divided the region of interest into a set finite elements, and calculated the arrival time differences between sensors by using the velocities at every degree from 0 to 90. A new technique for the source location of acoustic emission in fiberboard plates has been studied by introducing Wavelet Transform(WT) do-noising technique. WT is a powerful tool for processing transient signals with temporally varying spectra. If the WT de-noising was employed, we could successfully filter out the errors of source location in fiberboard plates by arrival time difference method. The accuracy of source location appeared to be significantly improved.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.210-215
• /
• 2002

MR(Magnetorheogical) fluid composed of fine iron powders dispersed in silicon oil is utilized to many smart structures and devices because of its significant rheological property change by the application of an external magnetic field. When we deal with the shock wave attenuation of warship structures, we should be able to characterize the high frequency behavior of MR fluids. So far, however, many efforts have been focused on the material characterization of MR fluids at low frequencies below 100Hz. In this paper, the MR fluid property characterization at high frequency region is performed. An experimental setup based on wave transmission technique is made and the storage modulus as well as the loss modulus of MR fluids are found from the measured data of speed sound and attenuation. Details of the experiment are addressed and the obtained storage and loss moduli are addressed at $50kHz{\sim}100kHz$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1988년도 춘계학술대회 논문집
• /
• pp.33-34
• /
• 1988

태양전지의 특성분석에 관한 최근의 동향을 고찰해 보기로 한단. 첫째, $CuInSe_2$와 비정질 실리콘 등의 광전압 용도의 태양전지의 재료선택에 관한 일반 규칙을 살펴 보고, 둘째, AM1 조건에서 보다 정확한 전지효율의 측정방법을 조사하며, 셋째, 태양전지의 중요 특성분석방법들을 소개 설명한다. 특히 생산 품질관리의 규모로 까지 확대적용이 가능한 다음과 같은 태양전지의 특성분석방법들의 장치개선 및 컴퓨터제어를 고찰하기로 한다. 전지효율 및 기타 전지특성을 위한 전류-전압 성질 측정장치, 양자효율을 위한 분광반응장치, 소수 이동자의 확산거리를 위한 표면광전압장치, 또한 에너지갭 내의 양자상태밀도를 위한 광열굴절장치 등이다.

• Geomechanics and Engineering
• /
• 제33권5호
• /
• pp.453-462
• /
• 2023

Intermediate Geomaterials (IGMs) are natural formation materials that exhibit the engineering behavior (strength and compressibility) between soils and rocks. The engineering behavior of such material is highly unpredictable as the IGMs are stiffer than soils and weaker/softer than rocks. Further, the characterization of such material needs exposure to both soil and rock mechanics. In most conventional designs of geotechnical structures, the engineering properties of the IGMs are either aligned with soils or rocks, and this assumption may end up either in an over-conservative design or under-conservative design. Hence, many researchers have attempted to evaluate its actual engineering properties through laboratory tests. However, the test results are partially reliable due to the poor core recovery of IGMs and the possible sample disturbance. Subsequently, in-situ tests have been used in recent years to evaluate the engineering properties of IGMs. However, the respective in-situ test finds its limitations while exploring IGMs with different geological formations at deeper depths with the constraints of sampling. Standard Penetration Test (SPT) is the strength-based index test that is often used to explore IGMs. Moreover, it was also observed that the coefficient of variation of the design parameters (which represents the uncertainties in the design parameters) of IGMs is relatively high, and also the studies on the probabilistic characterization of IGMs are limited compared with soils and rocks. With this perspective, the present article reviews the laboratory and in-situ tests used to characterize the IGMs and explores the shear strength variation based on their geological origin.

• 소성∙가공
• /
• 제8권4호
• /
• pp.364-373
• /
• 1999

For material characterization of semi-solid materials, backward extrusion process, which has been used in forming of hollow-sectioned products, was analyzed by the upper bound analysis in the current study. The existing kinematically admissible velocity field was applied to steady state at which there was no change in the assumed regions of velocity field. For unsteady state, new velocity field, as a function of dead zone angle, was proposed. Through the whole analysis, fiction between die and workpiece was also considered. It has been studied how the process variables, such as friction factor and punch velocity, and material parameters, such as strength coefficient, strain rate sensitivity could affect on analysis results. Finally, by the comparison with the finite element analysis, the reliability and efficiency of the proposed velocity field were discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.250-250
• /
• 2009

Thin film of $SnO_2$ was fabricated from plasma enhanced atomic layer deposition technology with bubbler type injector system by using TEMASn (tetrakisethylmethylamino tin) precursor. Mostly crystalline of $SnO_2$ films can be obtained with oxygen plasma and with water at relatively low temperature of $150^{\circ}C$. $SnO_2$ was deposited as an uniform rate of $1.0A^{\circ}$/cycle. In order to obtain uniform film, a seed oxide material was used before TEMASn deposition in ALD process. The process parameters were controlled to obtain dense thin film by atomic deposition methodology. The morphology and characterization of thin film with optimized process condition will be discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.245-246
• /
• 2006

A propyl alcohol based sol-gel method was used as to replace the 2-methoxyethanol with 1,1,1 tris (hydroxymethyl) ethane for preparation of pzt piezoelectric ceramic. The powder obtained by this sol-gel process were calcined at $900^{\circ}C$ and followed by the sintering at $1100^{\circ}C$ for ca2 hrs as to reach a pyrochlore-free crystal phase. The characterization of synthesized material was carried out by the XRD analysis and the surface morphology were determined by high resolution scanning electronmicroscopy. Further, the prepared small sized pzt thin powders are likely to be used m various applications.

• 대한기계학회논문집A
• /
• 제33권4호
• /
• pp.373-379
• /
• 2009

Presented in this paper is a new experimental technique to measure material properties of lock plate of gas turbine plants by using ultrasonic guided wave. In comparison with the mechanical destructive testings, material characterization of the Inconel x-750 was nondestructively carried out in a more efficient manner to discriminate the change in elastic moduli and the poisson's ratio attributed to the variation of heat treatment condition. The proposed technique shows a satisfactory feasibility via the comparative experiments with the imported lock plate specimens. It is also expected that the guided wave technique can cover a longer and wider range as a new cost-&-time-saving inspection tool due to the interaction with a greater part of specimen, compared to a conventional local point-by-point scheme.

• 한국전기전자재료학회논문지
• /
• 제14권3호
• /
• pp.202-206
• /
• 2001

Using THz time-domain spectroscopy (THz-TDS), the power absorption, the index of refraction, and the real conductivity of silica sand are measured from 0.1[Thz] to 0.5[Thz] frequency range. It is impossible to measure the characterization of the silica sand by simple electrical measurements using mechanical contacts, e.g., Hall effect or four-point probe measurements. However, the THz-TDS technique can measure not only electrical but also optical characterization of he sample. Also this technique can measure frequency dependent results. Especially, the real conductivity was increased according to THz frequency. This is unusual material compare with metal and semiconductor materials; the measured real conductivity are not followed by the simple Drude theory.

• 한국전기전자재료학회논문지
• /
• 제14권5호
• /
• pp.397-404
• /
• 2001

This study describes the effect of γ-ray irradiation on the properties of insulation materials for low voltage cables in a nuclear power plant. The radiation effects were characterized by measuring OIT, FTIR, electrical properties of the irradiated specimens. As a result, they showed the decrease of OIT and the increase of chemical structural defects with the increase of γ-ray amount. Also, the electrical properties such as dielectrical constant, tan $\delta$ and current were changed by aging. These changes may come from the increase of chemical structural defects by $\delta$-ray irradiation.