• Journal of the Korean Society of Safety
• /
• v.12 no.2
• /
• pp.17-21
• /
• 1997

The fatigue crack propagation rate has so far been measured by the effective stress intensity factor range Δ K/sub eff/. But no research has been done to study how much the crack opening ratio influences the expectation of the fatigue crack propagation. Therefore, this paper evaluates of the crack opening ratio on the fatigue crack propagation life by using the method of parameter sensitivity study. Summarizing the result ; ( 1 ) When the crack opening ratio U' is high, the effect of U' gets larger than any other except for the material factor m. But when U' is low, the effect is also diminished. Therefore, the selection of the lowest value possible is desirable in the evaluation of life. (2) When the value of the material factor m is high, the effect of crack opening ratio U' is increased, at the same time the effect of the other parameters also increased wholly. The effect of material factor m itself on life is high, but in case the material factor m is high, that the effect of each parameter on life get higher is unique. In designing, better attention to the material selection should be drawn. (3) In case the stress ratio R gets smaller, the effect of crack opening ratio U' is unchangeable. But the effect of R itself remarkably decreases, and the effect of material factor m somewhat decreases.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.209-212
• /
• 2011

Selection of finishing materials in the design stage is an important management factor in terms of use safety and satisfaction, and work cost and process. However, selection of materials in the design stage is usually conducted without related guidelines or a set process, but depends on the experience of the architect or advice of materials company employees. Therefore, the aim of this study was to develop a finishing materials selection process that can be used by a architect. Materials selection related rules collected through interview with experts and five office building cases were used as knowledge. In addition, another aim of the study was to propose a prototype system interface for use in the field.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.27-30
• /
• 2014

Alloy tool steel such as SKD11 and SKD61 or high speed tool like SKH51 are used as materials for semiconductor dies. Cavities, curl blocks, pot blocks and housings are made from those materials. To make those parts from alloy tool steel or high speed tool, one utilizes discharge machining, and mechanical machining including machining center, milling, drilling, forming grinding and others. In the process of cutting machining and polishing, the die materials become unsuitable for machining owing to bubbles and foreign substances in them, which hinders production process. Therefore, this study focuses on die material selection criteria, and on analysis and comparison of material characteristics to help companies to solve their problems, make die manufacture less burdensome and extend die life.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2005.05a
• /
• pp.302-305
• /
• 2005

To comply to demand for a development requirement of aircraft design part, the expert system builds up standard knowledge-base based on presently maintained expert knowledge and experience in aircraft structure material selection. It also builds up database based on aircraft design open data, and standard calculation module used for present design and analysis method. This system is developed using Visual Basic language. The expert system standardize aircraft structure material selection and can be applied to all type of elementary stage of aircraft structure design. It is working on Windows, which has a friendly interface and is convenient for debugging, maintenance and transplanting. Explanation of the structure and the function of the system was given in this paper.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.18 no.33
• /
• pp.45-53
• /
• 1995

The Purpose of this paper is to describe and demonstrate a quantitative procedure for evaluating alternative material handling systems that are being considered for possible purchase. The procedure considers both quantitative factors(i.e. costs) and qualitative factors(i.e. equipment productivity) that should be considered in the evaluation process. Since these factors are not always quantifiable it is necessary that the procedure be able to quantify all factors in commensurable units. This is accomplished via a modification of the Brown and Gibson model for facility site location and selection. The model was demonstrated via a case example that encompassed the derivation of performance measures for three material handling systems.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.44-48
• /
• 2019

Motor core products are used as materials for electrical steel sheets and cold-rolled steel sheets according to the performance of motors. The cemented carbide material of the mold punch applied to the motor core material causes many troubles due to abrasion and burr problem. The selection of these materials has a great effect on the production life, mass production, product quality as well as mold life. The cemented carbide applied to the products of the motor core is recognized as a very important part. In this study, cold rolled steel sheet was applied to motor core SCP-1 steel 1.0mm, and The effects of abrasion and punching oil on the shear process were investigated for the selection of cemented carbide. Experiments were conducted to select and apply cemented carbide only for the motor core punch optimized for cold rolled steel. The results showed that the cemented carbide material of $CDK3^{***}$ produced the least wear and burrs.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.32-33
• /
• 2014

The appropriate selection of a construction material is important considering the effect on the total project cost and quality. However, the methodologies of the existing systems and databases to suggest search results have been analyzed to lack reliability. Therefore, this study suggests a material searching methodology that results in quantitative results using similarity.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2002.04a
• /
• pp.115-117
• /
• 2002

No Abstract, See Full-text

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.94-106
• /
• 2003

In recent years, the production value of Taiwanese mold and die industries have reached to a high peak in 1998, in amount of NT 604 hundred million dollars. But in recent years production value are going down year by year, till year of 2001 the production value have down to NT 394 hundred million dollars. Its main reason might be the major product were following in medium and low price category, the high accuracy and high cost mold and die still rely on import aboard. Therefore how to made the related technical database system on various field to provide the industry user to promote industries competition ability in mold and die is really urgent matter at this moment. In this research, we will offer how to apply the Visual Basic program language to edit a set of more perfect database system of mold and die material selection. At the present time, we have constructed complete Knowledge-Base-System of intelligence for forging mold and die material, the most related data from the existed data, the others are through our additional experimental results. By using this system by the user can got the related and need data easily, we hope it will reduce designing time and cost for mold and die.

• Korean Journal of Construction Engineering and Management
• /
• v.9 no.4
• /
• pp.84-91
• /
• 2008

"Eco-friendly construction" is an emerging issue in the building industry. Main purpose of the eco-friendly construction is to sustain the health and environment of building residents and to minimize the harmful effect on their environment. Apartment residents have great concern on eco-product, since many cases are reported that Sick Building Syndrome is caused by toxic substance from building materials. Environmental performance is to meet through using the highest grade eco-friendly materials. However, generally eco-friendly materials are more expensive than normal materials, Therefore, using eco-friendly materials at public housing project is limited to economical aspect. The purpose of this paper is development of eco-friendly material selection model considered cost efficiency. The selection of Eco-friendly finishing materials and their methods are constructed to consider environmental performance level and cost index compositively. Development of eco-friendly material selection method is economic and reasonable one when public housing is constructed.