• E2M - 전기 전자와 첨단 소재
• /
• 제10권9호
• /
• pp.960-967
• /
• 1997

• 한국재료학회지
• /
• 제2권3호
• /
• pp.220-227
• /
• 1992

전기유변유체(electrorheological fluid : ERF)는 크기가 $10^{-6}m$정도를 가진 분극성이 강한 입자 분말을 유전유체속에 혼합하여 만든 콜로이드용액으로서 외부전기 장에 의하여 액체상태로부터 겔(gel)상태로 상태변환을 한다. 상태변환과정은 가역과정이며 $10^{-3}$초 정도의 빠른 시간내에 이루어진다. 본 논문에서는 주기적응력이나 주기적 변형이 가해지는 강제진동실험을 통하여 ERF의 점탄성 특성을 조사하였다. 점탄성은 복소수로서 실수부인 동적전단탄성율(storage shear modulus, G')과 허수부인 동적손실율(loss modulus, G")의 합으로 표현된다. 동적전단탄성율은 강제진동의 진폭과 주파수의 함수로 외부전기장에 의하여 크게 변화되었으나 손실계수(loss factor, ${\eta}=G"/G'$)는 진동의 진폭, 진동수 및 외부전기 장에 거의 독립적이었다. 실험(1)은 강제진동의 진폭을 고정하고 진동수를 변화하는 방법(frequency sweep)과 실험(2)는 진동 진폭을 변화시키는 방법(amplitude sweep)으로 실행했다. 본 실험에서는 cornstarch입자를 corn oil에 혼합한 것과 zeolite입자를 silicone oil에 흔합한 콜로이드 용액이 ERF로서 사용되었으며 인가된 전기장은 약$(1~3){\times}10^6V/m$의 직류전기장이 가하여졌다.기장이 가하여졌다.

• 한국전기전자재료학회논문지
• /
• 제13권10호
• /
• pp.840-846
• /
• 2000

In this work, small-size, high-performance solenoid-type RF chip inductors utilizing a low-loss Al$_2$O$_3$core material were investigated. The size of the chip inductors fabricated in this work were 15$\times$10$\times$0.7㎣, 2.1$\times$1.5$\times$10㎣, and 2.4$\times$2.0$\times$1.4㎣ and copper (Cu) wire with 40 ㎛ diameter was used as the coils. High frequency characteristics of the inductance, quality factor, and impedance of developed inductors were measured suing an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). It was observed that the developed inductors with the number of turns of 7 have the inductance of 33 to 100nH and exhibit the self-resonant frequency (SRF) of .26 to 1.1 GHz. The SRF of inductors decreases with increasing the inductance and the inductors have the quality factor of 60 to 80 in the frequency range of 300 MHz to 1.1 GHz. In this study, small-size solenoid-type RF chip inductors with high inductance and high quality factor were fabricated successfully. It is suggested that the thin film-type inductor is necessary to fabricate the smaller size inductors at the expence of inductance and quality factor values.

• 한국농공학회지
• /
• 제20권1호
• /
• pp.4599-4613
• /
• 1978

This study was intended to investigate the effects of bituminous material content of soil-cement mixtures on their durability. For the purpose, unconfined compressive strength test, Freeze-thaw test, and wet-dry test were performed with three types of soil. Each type of soil was mixed with three levels of cement content and each soil-cement mixture was mixed with four levels of bituminous material content. For the unconfined compressive strength test, Freeze-thaw test and wet-dry test, 324, 108, and 108-specimens were prepared respectively. Unconfined compressive strength was measured at age of 7-days, 14-days and 28-days using 108-specimens in each age. The soil-cement loss rate due to freeze-thaw and wet-dry were calculated after 12 cycles of test using 108-specimens in each test. The results are summarized as follows : 1. Optimum moisture content was increased with increase of cement content, but maximum dry density was changed irregulary with increase of the cement content. 2. The unconfined compressive strength was increased with increase of cement content, bituminous material content and curing age. Cement is more effective factor than bituminous material on unconfined compressive strength of soil-cement Mixture. 3. It is estimated as the most economical cement content that the recommended cement content of A.S.T.M. because increasing rate of unconfined compressive strength at age of 28-days was low when cement content is above the recommanded cement content of A.S.T.M. among all types of soil. 4. Although a portion of cement content is substituted for bituminous material, the necessary unconfined compressive strength can be obtained. 5. The soil-cement loss was more influenced by wet-dry than Freeze-thaw 6. The bituminous material is more effective on the decrease of soil-cement loss than increase of unconfined compressive strength 7. The void ratio of soil-cement mixture was changet irregularly with increase of cement content, but that was decreased in proportion to the increase of bituminous material content. 8. The regression equation between the unconfined compressive strength and soil-cement loss rate were obtained as table 7.

• 한국전기전자재료학회논문지
• /
• 제18권6호
• /
• pp.532-537
• /
• 2005

In order to develop a tunable resonator which can be easily operated by DC bias and applied for microwave tunable filters and devices using ferroelectric thin or thick films, the non conductor backed-and conductor backed- coplanar stripline resonators have been designed and analyzed. They have been designed to be operated at 25 GHz which involve coplanar stripline input and output ports. The resonators have been simulated and analyzed using Ansoft HFSS. The research has been focused on the Quality factor of the coplanar stripline resonator. The conductor Q, box Q, and radiation Q of the resonators have been analyzed and calculated according to the substrate thickness & conductor width of the resonators. From these parameters, the loss factors of the coplanar stripline resonator have been investigated. The conducting Q of the coplanar stripline resonator has no relation with the thickness of dielectric substrate and increases as the conductor width increases. The box Q has no much relation with the thickness of substrate and the conductor width, which is above 2000. The radiation loss increases as the thickness of substrate and the conductor width increase. To decrease the radiation loss of the coplanar stripline resonator, a conductor backed coplanar stripline resonator has been proposed which has the unloaded Q of 170.

• Journal of Advanced Research in Ocean Engineering
• /
• 제3권1호
• /
• pp.1-14
• /
• 2017

The safety analysis of an earthquake is carried out during the operation of a subsea pipeline and an onshore pipeline. Several cases are proposed for consideration. In the case of a buried pipeline, permanent ground deformation by the earthquake and an increase of internal pressure by the acceleration of the earthquake should be considered. In the case of a subsea pipeline, a bending moment is caused by liquefaction of the backfill material on a trenched seabed, etc., which results in a high bending moment of the buried pipeline. The bending moment causes the collapse of the subsea pipeline or a leak of crude oil or gas, which results in economic loss due to enormous environmental contamination and social economic loss owing to operation functional failure. Thus, in order to prevent economic loss and operation loss, structurally sensitive design with regard to seismic characteristics must be performed in the buried pipeline in advance, and the negative impact on the buried pipeline must be minimized by conducting a thorough analysis on the seabed and backfilling material selection. Moreover, it is proposed to consider the selection of material properties for the buried pipeline. A more economical review is also required for detailed study.

• Corrosion Science and Technology
• /
• 제12권5호
• /
• pp.209-214
• /
• 2013

In the industry, accelerated corrosion test is used for the life time prediction. When anti-corrosion test proceeds in real environments, it is difficult that we predict and evaluate the corrosion life time because of the long test time such as 10 years or more time. Accelerated corrosion test and Salt spray test are able to test corrosion life time of products in the laboratory instead of outdoor corrosion test. Experimental procedure is selected for the corrosion standard specimen, exposure of the specimens, measurements of the mass loss and evaluating the mass loss data. As a result, the acceleration factor of the accelerated corrosion test to the outdoor corrosion test is 414.8. Therefore we can predict the corrosion life time of carbon steel during a short time period.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.149-152
• /
• 1997

High-power piezoelectric materials are being developed for applications such as actuators and ultrasonic motors. In this paper, ferroelectric property of iron-doped 0.57 (Sc$_{1}$2//Nb$_{1}$2/)O$_3$-0.43 PbTiO$_3$. which is the morphotropic phase boundary composition for the PSN-PT system, was investigated. The maximum dielectric constant ( $\varepsilon$$_{33}$/$\varepsilon$$_{0}$ = 2551) and the minimum dielectric loss(tan $\delta$ = 0.51 %) at room temperature were obtained at 01. wt% and 0.3 wt% of iron additions. With additions of the Fe$_2$O$_3$ the electromechanical coupling factor of radial mode k$_{p}$ and the piezoelectric coefficient d$_{33}$ were slightly decreased, on the other hand the mechanical quality factor was increased significantly. The highest mechanical quality factor (Qm= 297) was obtained at 0.3 wt% Fe$_2$O$_3$, which is 4.4 times larger than that of pure 0.57 PSN-0.43PT ceramics. The temperature dependence of the dielectric constant and dielectic loss was observed between 2$0^{\circ}C$ and 35$0^{\circ}C$ .X> .X> .

• Composites Research
• /
• 제12권2호
• /
• pp.1-9
• /
• 1999

외부 회로가 연결된 압전 재료는 외부 회로의 영향으로 진동수에 영향을 받는 강성(stiffness)과 손실 계수(loss factor)를 가지게 된다. 일반적으로 외부 회로는 두 종류로 구별이 된다. 저항만으로 구성된 경우와 저항과 인덕터(inductor)로 구성된 경우이다. 저항만으로 구성된 경우를 RES(resistive shunting)라 하는데, 이 경우는 압전 재료의 물성이 점탄성 물질과 비슷하게 진동수에 영향을 받는다. 그러나 점탄성 물질에 비해서 더 큰 강성을 지니고, 온도에 영향을 덜 받는다. 저항과 인덕터로 구성된 경우를 RSP(resonant circuit shunting)라 하는데, PMD(proof mass damper)와 비슷한 방법으로 구조물의 공진을 최적으로 조절할 수 있다. 본 논문에서는 이러한 외부 회로와 연결된 압전 재료를 이용하여 복합재 보의 진동을 수동적으로 제어하는 실험을 수행하여 그 결과를 제시하였다.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.468-479
• /
• 2016

고압 전선 등에 장착된 시스템에 전원을 공급하기 위해서는 절연 이격 거리 이상의 거리에 무선으로 수십 Watt 급의 전력을 보낼 수 있는 시스템이 필요하다. 이러한 무선 전력 전송 시스템은 대개 코일의 크기가 10cm 이상의 대형이다. 본 연구에서는 이처럼 대형 코일을 Printed circuit board를 이용해 제작할 경우 발생하는 손실 발생원 들을 분석하고 그 중 가장 주요한 손실원인이 Dielectric loss 라는 것을 밝혔다. 또한 이 dielectric loss를 최소화 하기 위해서 PCB의 재질 선정 방법 및 Distributed tuning capacitor method를 제시해 $40cm{\times}40cm$ 크기의 4턴 및 5턴 코일의 설계 방법을 제시했고, 실험을 통해 Quality factor를 300 이상으로 만들 수 있음을 보였다.