• Journal of information and communication convergence engineering
• /
• 제13권3호
• /
• pp.159-166
• /
• 2015

In this paper, a novel design for a triple-band coplanar waveguide (CPW)-fed monopole antenna for WLAN/WiMAX operations is proposed. The proposed antenna is printed on an FR4 substrate with an area of 22.0 mm × 30.0 mm, a thickness of 1.0 mm, and a relative permittivity of 4.4. The effects of various parameters of the proposed for triple band operation is investigated. Two half circular rings and a microstrip feed line are fabricated on the substrate to achieve triple band operation and good impedance matching. Prototypes of the proposed antenna have been fabricated and tested. Experiment results reveal that the measured return loss exhibits an acceptable agreement with the simulated return loss and satisfies the impedance bandwidth requirement of -10 dB, while simultaneously covering the WLAN and WiMAX bands. In addition, the proposed antenna shows good radiation characteristics and gains in the three operating bands.

• 태양에너지
• /
• 제18권1호
• /
• pp.35-43
• /
• 1998

In two terminals monolithic tandem solar cells, tunnel diode is an important variable to improve conversion efficiency depending on current matching between the top and the bottom cells. Especially, the GaAs/Ge tandem is one of the most interesting cells for its high potential efficiency. This paper shows that physical analysis about I-V specific character of the GaAs/Ge solar cell, which is grown by MOCVD for GaAs or CVD for Ge, using computer simulation and experimental results, varying with thickness of the tunnel diode layer and concentration.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.11-15
• /
• 2002

High speed probe for measurement of sin91e flux quantum circuits is comprised of coaxial cables and microstrip lines in order to carry high speed signals without loss. For the impedance matching between coaxial cable and microstrip line, we have determined the dimension of the microstrip line with 50${\Omega}$ impedance by simulation and then have investigated the effect of line width and cross-sectional shape of signal line, dielectric material, thickness of soldering lead at the coaxial-to-microstrip transition Point, and the an91c between dielectric material and end part of the signal line on the characteristics of signal transmission of the microstrip line. From the simulation, we have found that these all parameter's had influenced on the characteristic of signal transmission on the microstrip line and should be reflected in fabricating high speed probe, We have also determined the dimension of coplanar waveguide to fabricate testing sample for performance test of high speed probe.

• 항공우주기술
• /
• 제3권1호
• /
• pp.257-266
• /
• 2004

고차 지그재그이론을 이용하여 면내회전 자유도를 갖는 3절점 삼각형요소를 개발하여 복합재 적층판의 층간 응력분포를 정확히 계산하였고 점탄성물질이 심어진 비틀린 복합재료 판의 진동을 해석하였다. 평면상에서 점탄성물질과 가장자리에서 박리현상을 방지하기 위하여 사용된 경계물질사이의 경계면상에서 전단력 적합조건이 사용되었다. 본 연구에서 개발된 지그재그 삼각형요소를 이용하여 점탄성물질이 심어진 비틀린 외팔보 복합재료판의 고유진동수와 감쇠계수를 계산하고 실험치 및 판과 고체요소를 혼합한 MSC/NASTRAN 결과치와 비교하였다.

• 한국전자파학회논문지
• /
• 제10권5호
• /
• pp.727-737
• /
• 1999

마이크로스트립 안테나는 츄전체층이 있으므로 해서 대역폭과 방사 효율의 제한을 받고 있다는 것은 잘 알려져 있다. 본 논문에서는이러한 제한을 극복하기 위해 유전체를 갖고 있는 구조체의 사용대신 금속봉이나 비금속봉으로 지탱되는 금속판으로 구성된 구조체를 사용한다. 본 연구의 가장 중요한 동기는 기존의 안테나보다 높은 방사효율을 보이는 광대역 마이크로스트립 안테나를 구현하는 데에 있다. 또한 대역폭의 증가를 위해 패치의 크기와 높이 그리고 임피던스 정합이 고려된다.

• 한국전자파학회지:전자파기술
• /
• 제5권4호
• /
• pp.40-46
• /
• 1994

전파무향실에 사용 적합한 평면 페라이트 전파흡수체의 설계 및 , 그리고 전파흡수특성에 관해 연구하였다. 임피던스 정합 방정식의 엄밀해를 이용하여 페라이트 흡수체의 복소투자율 범위에 관해 분석하였다. 페라이트 소결제의 복소투자율 및 복소유전율로부터 정합주파수 및 정합두께를 결정하고 실측한 반사감쇠특성과 비교하였다. 전파흡수특성과 재료정수와의 상관관계에 대한 분석결과에 의거하여 정합주파수 및 정합두께의 조절을 위한 재료정수의 제어방안에 관해 검토하였다. 검토하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.278-281
• /
• 1999

We designed and fabricated a travelingwave CPW(coplanar waveguide) electrode for LiNbO$_3$ optical modulator. To Investigate the variation of microwave refractive index of these electrodes, we prepared the CPW electrode samples as a function of electrode thickness and measured the TDR and S-parameter. From this results, we could know the electrode conditions of index matching to 2.20 for 1150 nm optical wave index for applying LiNbO$_3$ optical modulator. Also we discussed the some properties of CPW electrode for applying LiNbO$_3$ optical modulator.

• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.158-165
• /
• 2009

We present cross-correlation frequency-resolved optical gating (XFROG) measurements of supercontinuum pulses generated by using a photonic crystal fiber (PCF), and ultraviolet (UV) pulses generated by frequency doubling of infrared ultra-short pulses. Since supercontinuum pulses have broad spectra, XFROG measurement typically requires using an extremely thin nonlinear crystal which has a thickness of sub-ten microns. Instead of using such a thin crystal, we employed a relatively thick crystal which was mounted on a galvanometer in order to achieve a phase-matching over the whole spectral bandwidth of the supercontinuum pulses by a crystal-dithering technique. Experimental results of the retrieved phase and intensity were in fair agreement with the independently measured data.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권2호
• /
• pp.79-82
• /
• 2004

The RF inductive discharge or inductively coupled plasma (ICP) continues to attract growing attention as an effective plasma source in many industrial applications, the best known of which are plasma processing and lighting technicology. Although most practical ICP operate at 13.56 [MHz]and 2.65 [MHz], the trend to reduce the operating frequency is clearly recognizable from recent ICP developments. In an electrodeless fluorescent lamp, the use of a lower operating frequency simplifies and reduces cost of rf matching systems and rf generators and can eliminate capacitive coupling between the inductor coil and plasma, which could be a strong factor in wall erosion and plasma contamination. In this study, the configuration of ferrite and fixture which operates at the frequency of 2.65[MHz]was discussed as functions of the ferrite thickness and distance by using the electromagnetic simulation software (Maxwell 2D).

• Journal of Magnetics
• /
• 제5권4호
• /
• pp.143-146
• /
• 2000

In this study, the magnetic properties of CoCrPt films (far longditudinal recording) on a novel VMn underlayer were measured and compared with similar films on conventional Cr underlayers. It was found that the VMn film had (200) preferred orientation and the lattice constant was about 0.2967 nm, which is slightly larger than that of the Cr film, 0.2888 m. The grain size of the VMn film was 9.8 nm at 30 m thickness, about 39% smaller than that of a similarly deposited Cr. The CoCrPt/VMn films showed higher coercivity in comparison with the CoCrPt/Cr films. The coercivity increase is attributed to the increased Co (11.0) texture, improved lattice matching between Co (11.0) and VMn (200), and lower stacking fault density. V or Mn must have diffused into the CoCrPt magnetic layer uniformly rather than preferentially along grain boundaries. This reduced Ms at higher substrate temperature.