• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.4
• /
• pp.181-185
• /
• 2017

In this paper, for Broadband Wireles LAN dual-band antenna was designed to satisfy the bandwidth of 2.32GHz and 5.79GHz. the substrate of proposed microstrip antenna is FR-4(er=4.3) and $34mm{\times}50mm{\times}1.5mm$ size and thickness t=0.035mm, and the simulation was used for CST Microwave Studio 2014. input return loss compared -10dB less than operates at and when gain 2.32GHz -19.321dB, 5.79GHz showed the results of -13.033dB. It increased impedance matching, minimized interference between adjacent frequencies, simplified small manufacturing methods, and demonstrated the characteristics of non-directional properties. Thus the proposed antenna satisfied the -10 dB impedancebandwidth requirement while simultaneously covering the Broadband Wireless LAN.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.3
• /
• pp.1-9
• /
• 2003

In this paper, we designed a highly suppressed sidelobe ladder type RF SAW bandpass filter based on 1-port resonator, for 800 MHz mobile communication system. In order to get the highest device characteristics, we optimized some important parameters such as the electrode thickness, electrode lambda weghting of the reflectors, and static capacitance ratio. Furthermore, we fabricated the Tx and Rx. filter using optimized parameters. Implemented filters can be used in 800 MHz mobile communication system and external impedance matching circuits are not needed. RF filter was fabricated on 36$^{\circ}$LiTaO$_3$ substrates with Al-Cu (W 3 %)and mounted 3.8mm$\times$3.8mm$\times$1.5mm SMD package. Developed filters has 2.3 dB insertion loss in the 25 MHz pass-band, 33MHz with 3-dB insertion loss, stop-band rejection of 30 dB, passband ripple is less than 0.5 The power durability of the filters measured about 3.5W and the maximum temperature variation within -2$0^{\circ}C$~8$0^{\circ}C$ was 0.09 dB/$^{\circ}C$ of 3-dB insertion loss.

• Journal of the Korean Home Economics Association
• /
• v.45 no.4
• /
• pp.43-51
• /
• 2007

This study analyzed the knit wear trend, which has gained attention as a sensuous and luxury item, through collection magazines, and used the technique of hand-knit to produce and present the knit wear that was designed based on the study results. Accordingly, the purpose of this study is to raise awareness of the expansion of hand knit's new expression techniques and expression areas and to verify its possibility as a higher value-added product. The trends of hand-knit wear resulted from the analysis of collections divided into the following four groups, and the knit designs were also grouped accordingly: First was "The design using object." The trend survey showed the results that the form of drops or flowers was often used as a factor of object. Accordingly, as for the study design, the drop-knitting technique, which is one of the pattern knitting techniques, was used to present a design that employed drops as the object. Second was "The design matched with woven material." It is a way to emphasize aesthetic formativeness and at the same time to activate the area of knit design by matching woven material, which is different from knit in texture, with knit. This study presented a design that tried to combine knit texture and woven material by connecting denim material with various textures and colors. Third was "The design to express see-through." A sense of showing through knit wear was expressed through changes in the type of thread or knitting technique. In this study, the sense of see-through was expressed using piano wires and wool threads and through changes in the thickness of needle. Fourth was "The design to emphasize coloring." It was analyzed that regarding the production of hand knit, the method of coloring expression was to express points, lines and sides or to create harmony by changing the material's color or texture to show particular objects or shapes. In this study, a jacket was designed using the method to express points, lines and sides by changing the material's color.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.8
• /
• pp.32-41
• /
• 1999

In this paper, an inversion method using chirp signals and two near field receivers is proposed. Inversion problems can be formulated into the probabilistic models composed of signals, a forward model and noise. Forward model to simulate chirp signals is chosen to be the source-wavelet-convolution planewave modeling method. The solution of the inversion problem is defined by a posteriori pdf. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the ranges for a priori uniform distribution is based. The genetic algorithm can be applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L₂norm of the difference between measured and modeled signals. The observed signals can be separated into a set of two signals reflected from the upper and lower boundaries of a sediment. The separation of signals and successive applications of the genetic algorithm optimization process reduce the search space, therefore improving the inversion results. Not only the marginal pdf but also the statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm. The examples applied here show that, for synthetic data with noise, it is possible to carry out an inversion for sedimentary layers using the proposed inversion method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.388-402
• /
• 2000

The radiation characteristics of leaky antenna from the dielectric-coated conducting cylinder with periodic corrugation are investigated theoretically for the infinite and finite periodic structures. For the infinite periodic structure, mode-matching method is applied. The integral equation is derived for the finite periodic structure by use of the Fourier transform and mode expansion and a simultaneous linear equation is obtained. The influences of the corrugation slot width, corrugation depth, dielectric thickness, cylinder radius, and finite corrugation number on the radiation characteristics (leakage constant, phase constant, and radiation pattern) are investigated. The results of the finite periodic corrugations are compared with those of the infinite extent structure and good agreement is found. To reduce high side lobe levels of the uniform finite periodic structure, tapering process on the beginning and end section of antenna and nonuniform quasi-period slot arrays are considered. Especially, for the corrugation period, width and depth used for a corrugated surface wave antenna, through the proper tapering process, end-fire radiation pattern with reduced side lobe levels is given.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.11
• /
• pp.1047-1052
• /
• 2016

In this paper, we propose the CSLR(: Complementary Single Loop Resonators)-loaded inset fed patch antenna with a conducting reflector to improve the radiation patterns. Reflector of the proposed antenna is located below about ${\lambda}_0/4$ from the ground plane of the patch, the size is about two times of the patch. The proposed antenna is designed and fabricated on the substrate which has a dielectric constant and thickness with 2.5 and 0.787 mm, respectively. Simulation results are obtained by using the HFSS, 3D EM Solver based Finite Element Method(: FEM). The resonant frequency and matching characteristics of the antenna with reflector are substantially the same as when there is no change in the antenna without reflector, it is confirmed that radiation patterns are significantly improved by the reflector.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.4
• /
• pp.86-101
• /
• 1990

The primary objective of this research was to investigate the strength properties of Comply, a composite panel. fabricated with particle board as core material and veneer or plywood as face and back. 20types of comply composites were manufactured according to the four specific gravity levels(0.5, 0.6, 0.7 or 0.8) of particleboard core and three veneer or two plywood thicknesses for face and back. They were tested and compared with matching particleboard (control) on moisture content. specific gravity, bending properties(MOE, MOR SPL). nail resistance and internal bond strength. The obtained results were summarized as follows: The increasing effect of modulus of elasticity was shown by the increase of face and back veneer or plywood thickness. The modulus of rupture and stress at proportional limit of the comply composites bonded with 3mm thick veneers or 3mm thick plywood face and back were higher than 2mm thick veneer or 2mm thick plywood as face and back. Both of modulus of rupture and stress at proportional limit on bending of Comply were higher than those of control board. Also the modulus of elasticity of Comply showed much higher than that of control board. The nail resistance of Comply, composed of plywood as face and back was higher than that of veneer. The nail resistance of control board was higher than that of Comply at Sp.Gr 0.7 and 0.8 core boards. Internal bond of Comply, composed of 1mm and 2mm thick veneer as face and back was higher than that of 3mm thick veneer. The increasing effect of modulus of elasticity was shown by the increase of shelling ratio in Comply composed of veneer and plywood as face and back. The modulus of rupture was increased by the increment of shellmg ratio in Compiy, composed of plywood as face and back. The modulus of elasticity and modulus of. rupture of comply were higher than those of particleboard(control) in effect of shelling ratio. Therefore it was concluded that the mechanical property values of Comply were clearly greater than those of particleboard(control).

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.70-77
• /
• 2010

This study proposed an auto focusing method for a multi-focus image in assembling lens modules in digital camera phones. A camera module in a camera phone is composed of a lens barrel, an IR glass, a lens mount, a PCB board and aspheric lenses. Alignment among the components is one of the important factors in product quality. Auto-focus is essential to adjust image quality of an IR glass in a lens holder, but there are two focal points in the captured image due to thickness of IR glass. So, sharpness, probability and a scale factor are defined to find desired focus from a multi-focus image. The sharpness is defined as clarity of an image. Probability and a scale factors are calculated using pattern matching with a registered image. The presented algorithm was applied to a lens assembly machine which has 5 axes, two vacuum chucks and an inspection system. The desired focus can be determined on the local maximum of the sharpness, the probability and the scale factor in the experiment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.35-41
• /
• 1997

A series-fed microstrip array antenna of beamwidth $10^{\circ}$, squint angle $80^{\circ}$ and SLL -15 dB below is designed. Series-fed arrays are formed by interconnecting all the elements by high-impedance transmission lines and feeding the power at the first element and it is a traveling-wave antenna which is terminated with a matched load. Radiation patterns and impedance matching of the antenna are analyzed by Ensemble 4.0, which is a popular software package for designing printed antennas and arrays. The squint angle of beam can be controlled by the spacing between the elements. The major advantages of series-fed array antennas are that feed arangement is compact and the losses associated with the feeding network are less than those of a corporate feed type. The antennas are fabricated on the RT/Duroid Laminates of 62 mil thickness. The experimental results are very close to the specifications to be designed.