• Journal of the Korean Geosynthetics Society
• /
• v.16 no.1
• /
• pp.53-61
• /
• 2017

Seabed settlement and erosion sometimes occurr when a artificial reef is installed in soft seabed. Therefore, this study carried out CBR test and water tank settlement test to investigate settlement behavior of artificial reef according to reinforcement characteristics such as reinforced types and reinforced area. Soil types of ground are sand, silt and clay deposits. Three reinforced types were prepared: unreinforced, geogrid and hybrid bamboo mat(HBM) with different reinforced area. Laboratory test results indicated that reinforced artificial reef improved bearing capacity of ground and reduced settlement as reinforced area increased. Especially, reinforced HBM provided more bearing capacity and less settlement than reinforced geogrid.

• Journal of Korean Society of Forest Science
• /
• v.13 no.1
• /
• pp.67-78
• /
• 1971

The measures of contour-terracing with sod has been executed as a major measures for hillside erosion control works for a long time in Korea. It is, however, recognized that pair terracings make a new slope-face having the more steeper degree of slope between the upper and the lower terraces on hillsides and it also does not contribute for establishing the natural vegetation-cover by penetration of pioneer seeds on the slope faces or cut-faces of hillsides. The study was therefore conducted in connection with the above problems on the cut-face having slope of $40^{\circ}$ and 1.6 meter in slope length with clay soils. Plot allocation for the experiment consists of 3 kinds of 3 replica plots having each $1.6m^2$ of slope area, i. e., the control plot with direct seeding on slopes only ($T_1$), the covering plot with the straw-mats after seeding on slopes ($T_2$) and the seeding plot after covering with the straw-mats. ($T_3$). The main results obtained may be summarized as follows : 1. Effects of the straw-mat mulchings on surface soil loss control:-The total amount of soil losses from each treatments are measured as 4,651 gr from $T_1$, 163 gr. from $T_2$ and 2,891 gr. from $T_3$ treatment respectively. (Refer to table No. 2, 3 and 4). In short, it is recognized that effect of $T_2$ treatment is compared as 28.5 times than that of $T_1$ treatment and 17.7 times than that of $T_3$ treatment respectively. Effect of $T_3$ treatment compared with $T_1$ treatment is also such recognizable as 1.6 times in control of surface soil losses on a slope face. 2. Effect of the straw-mat mulchings on soil moisture content on slopes; -Average per cent of surface soil moisture content by treatments show as 21.60 at the $T_1$, 23.04 at the $T_2$ and 22.21 at the $T_3$ treatment respectively and that of subsurface soil moisture content by treatment show as 23.81 at the $T_1$, 26.16 at the $T_2$ and 24.81 at the $T_3$ treatment respectively. The variance of soil moisture content by treatments was highly significant (Refer table No. 7, 8 and 9). 3. Effect of the straw-mat mulchings on vegetation establishment;-Average numbers of germination by treatments are counted as 237 Nos. at the $T_1$, 246 Nos. at the $T_2$ and 262 Nos. at the $T_3$ treatment plots and the vegetation coverage on ground was almost same as about 90% of covers in all treatments. This effect is more or less lower than that of surface soil erosion control. 4. Regarding the effect on surface soil erosion control, the straw-mat mulchings would be effective as a new measures for control of soil erosion on erosion susceptible lands such slope-faced bare-lands as cut-fill faces, mass-movement faces and bare hillsides.

• Korean Journal of Agricultural Science
• /
• v.6 no.2
• /
• pp.166-184
• /
• 1979

In order to prevent the water loss in the irrigation canal constructed on the sandy gravel layer or on the other highly permeable ground layer, lining has been practiced. Many studies have been done so far on the lining method to prevent the water loss in the irrigation canal and recently studies on the lining with plastic film or polyethylene film were also reported. However, the plastic film or polyethylene film has low strength and is liable to break, and water loss from pin hole caused by contacting with sand or gravel is highly predicted. This study was then conducted to find proper lining and buring method in canal construction of polypropylene mat after coated with vinyl, as one way to overcome the shortcoming frequently observed when plastic or usual polyehtylene film were used. Eventhough rather longer periods of experiments are needed to attain reliable and accurate results on the variation of durability, the durability of asphalt coated area, or on the damage due to freeze after burial or exposure of polypropylene mat, the experiemental results obtained during one year of period are summarized as follows: 1. The curvature at the area between canal bottom and side slope had increased stability and saved consruction cost. The relationship among the variation of curvature, the reduction of polypropylene mat and the reduced amount of soil cutting at each side slope was presented in Fig. 7 through 9. 2. The depth of covering material to protect polypropylene mat was desired to be over 30cm, considering the water depth, side slope, canal cleaning practices, traffic, or back pressure of irrigation period. 3. In order to increase the canal stability and to prevent slope erosion, sandy soil was required, to be placed under ground, and coarse gravel should cover the surface area of canal. 4. The studies on the stability of side slope in the canal should consider the passive area on the bottom and the slope should be about 1 to 2, considering the slope stability, allowable velocity and tractive force. 5. When compared with earth lining, the lining with polypropylene mat coated with vinyl was responsible to save 28% and 37% of canal lining cost, when the soil carrying distances were 500 and 700m. respectively. 6. The water interception was almost completely attained when the polypropylene mat coated with vinyl was used for lining. But further studies were assumed to be necessary for the use of asphalt since the strength of polypropylene mat connected with asphalt will vary with duration.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.468-472
• /
• 2010

To develop the Exhaust Maniverter(Manifold and converter) it needs to consider flow characteristics related to durability and performance of the catalyst, manufacturability, etc. This paper presents the analysis results regarding to flow characteristics such as flow uniformity, tangential speed, O2 sensor sensitivity and CHT (conjugate heat transfer) for the LCF(Low Cycle Fatigue) for gasoline 2.0 liter engine. The results are satisfactorily corresponded to the general criteria. Also skin temperature and pressure drop wire measured at the Engine Bench. These results can be useful for the design guide for Exhaust Maniverter.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.1
• /
• pp.109-116
• /
• 2024

The Rapid Hardening Composite Mat (RHCM) is a product that improves the initial strength development speed of conventional Geosynthetic Cementitious Composite Mats (GCCM). It offers the advantage of quickly securing sufficient strength in railway slopes with insufficient formation level, and provides benefits such as preventing slope erosion and inhibiting vegetation growth. In this study, an analysis of the practical applicability of RHCM in railway settings was conducted through experimentation. The on-site applicability was assessed by categorizing it into fire resistance, durability, and stability, and conducting combustibility test, ground contact pressure test, and daily displacement analyses. In the case of South Korea, where a significant portion of the territory is composed of forested areas, the prevention of slope fires is imperative. To analyze the fire resistance of RHCM, combustibility tests were conducted as an essential measure. Durability was assessed through ground contact pressure tests to analyze the deformation and potential damage of RHCM caused by the inevitable use of small to medium-sized equipment on the construction surface. Furthermore, daily displacement analysis was conducted to evaluate the structural stability by comparing and analyzing the displacement and behavior occurring during the application of RHCM with railway slope maintenance criteria. As a result of the experiments, the RHCM was analyzed to meet the criteria for heat release rate and gas toxicity. Furthermore, the ground contact pressure was observed to be consistently above 50 kPa during the curing period of 4 to 24 hours under all conditions. Additionally, the daily displacement analyzed through field site experiments ranged from -1.7 mm to 1.01 mm, confirming compliance with the criteria.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.2
• /
• pp.95-102
• /
• 2012

The objective of this research was to experimentally test the effect of rice straw mats on the reduction of runoff, sediment discharge and turbidity under a laboratory scale. We used the small runoff plots of 1 m ${\times}$ 1 m ${\times}$ 0.65 m ($L{\times}W{\times}H$) in size filled with loamy sand. Experimental treatments were bare (control), rice straw mat cover of straw mats + PAM + Gypsum (SPG), rice straw mats + Chaff + PAM + Gypsum (SCPG) and rice straw mats + Sawdust + PAM + Gypsum (SSPG); slope of 10 % or 20 %; and rainfall intensity of 30 mm/hr. Runoff volume and rate of covered plots were significantly lower than those of control plot. Average runoff rate of covered plots, slope of 10 % and 20 %, decreased 85.6 % and 72 % in respectively. Sediment reduction ratio was more than 99 % regardless of slope. The differences runoff and sediment discharge among different cover materials were not significant. It was also shown that even if runoff reduction by surface cover were low, sediment discharge reduction could be very significant and contribute to improve the water quality of streams in sloping agricultural regions. It was concluded that the use of straw mat and soil amendments (PAM and Gypsum) on sloping agricultural fields could reduce soil erosion and muddy runoff significantly and help improve the water quality and aquatic ecosystem in receiving waters. But mixing effect of PAM and Gypsum was minimal.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.2
• /
• pp.27-35
• /
• 2012

Various Best Management Practices (BMPs) have been suggested to reduce Nonpoint source pollutant loads from agricultural fields. However, very little research regarding water quality improvement with sediment trap has been performed in Korea. Thus, effects of sediment trap were investigated in this study. Three sediment traps were installed at the edge of six plots and flow and water quality of inflow and outflow were monitored and analyzed. It was found that approximately 64.1 % of flow reduction was observed. In addition, pollutant concentration of outflow was reduced by 39.0 % for $BOD_5$. For SS, $COD_{Mn}$, DOC, T-N, T-P, approximately 62.1 %, 43.4 %, 43.5 %, 40.0 %, and 41.2 % reduction were observed, respectively. Over 80 % and 90 % of pollutant loads were reduced from sediment trap #2 and #3 because of less outflow from plots covered with rice straw/straw mat. In case of intensive rainfall events occurred from July 26~29, 2011, over 60 % of pollutant and 88.9 % of sediment reduction were observed from sediment trap #3. As shown in this study, small sediment traps could play important roles in reducing pollutant loads from agricultural fields. If proper management practices, such as rice straw/straw mat, are used to protect surface from rainfall impacts and rill formation, much pollutant reduction could be expected.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.6
• /
• pp.139-151
• /
• 2007

To protect the surface of ground-cutting slopes and ground-raised slopes and to recover environment-friendly slopes at the national road expansion construction between Gamchon and Yaechon, test-construction work was done using several modes of hydro-seeding measures to select a suitable construction method through the field survey; the results were as follows : As a result of survey on physio-chemical characteristics of soil, the average soil inclination on ground-raised slopes was from 4.73 mm to 5.37 mm; the average soil acidity was from pH 6.47 to 6.73; the average soil humidity was within the scope of 0.57~1.70 %,; the average soil inclination on ground-cutting slopes was 9.17~10.43mm; the average soil acidity was pH 6.67~6.77 and the average soil humidity was within the scope of 0.53~1.27 %; considered overall, they showed generally satisfactory base materials for plant breeding. As a result of the number of sprouting individuals, the average sprouting number of individuals on test spots executed by Coir net with Seed spray construction methods and the average number of sprouting individuals on other test spots executed by furrow-digging with Seed spray and Straw mat-mulching measures were 1,172 number of per square meter and 970 number of per square meter respectively; thus they showed higher numerical value comparing with other test spots. Likewise, the average number of sprouting individuals on test spots of the ground-cutting slopes executed by Coir net with Seed spray method and the average number of sprouting individuals on other test spot executed by furrow-digger with Seed spray and Straw mat-mulching measures were found to be 1,107 number of per square meter and 1,105 number of per square meter respectively, whose numerical value showed rather higher other test spots. As a result of a survey on living plants' breeding index [dried weight], the weight in dried state on test spots executed by Coir net with Seed spray method and other test spots executed by furrow-digger with Seed spray and Straw mat-mulching measures on both ground-raised and ground-cutting slopes was found to be higher and showed similar characteristics statistically. As a result of survey on the surface-covering degree of ground-raised slopes, nine weeks after test construction, test spots executed by Coir net with Seed spray method and other test spots executed by furrow-digger with Seed spray and Straw mat-mulching measures showed commonly more than 70% of surface-covering degree, but other test spots showed only below 35% of surface covering degree; especially in case of test spots by Verdvol seed spray measures, they showed 10% of the lowest surface-covering. Surface-covering degree on the test spot of ground-cutting slopes nine weeks after test construction showed more than 75% both executed by Coir net with Seed spray construction method and executed by furrow-digger with Seed spray and Straw mat-mulching measures. As a result of survey on appearing plants on the test spots, there dominates Eragrostis curvula both on ground-raised slopes and on ground-cutting slopes with other seeding plant life's lower breeding and there appear intruders, such as Setaria viridis Beauv, Digitaria sanguinalis Scop, and Chenopodium album var.centrorubrum Makino. As for water-borne excavation and soil's washing-away on the slopes, there happened less washing-away and water-borne excavation with good breeding of plant life on test spots executed both by Coir net with Seed spray construction method and by furrow-digger with Seed spray and Straw mat-mulching measures, but there happened much more soil's washing-away along with water-home excavation at the test spot executed by Seed spray with measures. After the research results of test construction sites are examined overall, it's presumed that furrow-digger with Seed spray and Straw mat-mulching measures [interval between lines is 40cm, 5cm in depth] will be preferred to prevent erosion and water-home excavation of slopes located within the construction sites.

• Journal of Korean Society of Forest Science
• /
• v.81 no.1
• /
• pp.53-65
• /
• 1992

For elucidating effective methods of restoration of forest recreational sites where management goals are maintaining naturalness and conserving natural ecosystem, seeding, fertilization and soil surface treatment were used for four years at the devastated forest-floor. For restoration of forest-floor vegetation, factorial experiment was used with a split plot design(main plot : fertilization, subplot : soil surface${\times}$seeding) and a randomized complete block design (fertilization${\times}$seeding) at the Kwanaksan Aboretum, Anyang, Kyonggido. Results were summarized as follows : Soil surface softening with tipping and ripping and straw-mat mulching (70% coverage) treatment was effective on germination, survival and growth of seeded vegetation at devastated forest-floor. Especially, straw-mat mulching treatment was effective on soil surface stabilization and seedling's survival at eroded soil surface, while complete soil surface softening treatment was effective on germination, survival and early growth of tree species of late-successional series. Introducing seeds of native species of pioneer or early-successional series, with good growth capability in barren soil was effective on rapid restoration in devastated forest-floor with its soil surface previously compacted and its surviving seeds washed away. When the seeding and straw-mat mulching after partial soil surface softening with tipping and ripping treatment were employed, it took about three years to restore the devastated forest-floor where surface erosion had been undertaken for an extended period of time and where naturally surviving seeds of native species had been washed away. Softening treatment of soil surface was effective for about two years, and seeding and soil surface treatment increased number of seedlings and improved soil surface environment through fixing of movement of the fallen leaves. Fertilizing effect was not oberserved, mainly due to seeding exposure and poor physical condition including soil surface erosion, low soil water potential and drought, etc, at the field experimental site. However, application of nitrogen and phosphate fertilizers was effective on seedling survival of the species in late-successional series, while lime application adversely affected the seedling survival.

• Journal of Korean Society of Forest Science
• /
• v.24 no.1
• /
• pp.1-24
• /
• 1974

A national programme of erosion control for soil and water conservation needs to be based on factual information about rates and quantities of soil erosion and of water runoff. The best and simplest way of reducing sedimentation pollution is to prevent or control the erosion at its sources. Steeply sloping earth banks are liable to both surface erosion and land-slides and the key to the control of these form of erosion lies with drainages and dense vegetation establishment including surface mulching on the slopes. Micro-plots having $1.6m^2$ (1 metre in width and 1.6 metres in slope length, and 1:1.2 in gradient) of banking slopes on the coarse sand soil are used to establish the order of magnititude of the difference in controlling of soil erosion and water runoff, and in potentiality of execution in consideration of the values of landscapes, performed on the 2 repetetions of six-experiment plots consisted of five surface mulches including seedings and one bare slope as a control treatment. The main results obtained may be summarized as follows: 1. The significant difference is realized in the quantities of soil erosion between the measures of six treatments. 2. Excepting the differences between treatment III and VI, the significant difference is realized in the rate of surface runoff between each treatment measures. 3. Both measures of treatment II and IV are recognized as the most effective measures in controlling the soil erosion and water runoff and also in establishing the ground vegetation. (Treatment II is a measures of the coarse straw-mat mulchings on the micro-strip seedings, Treatment IV is a measures of the "SPRAY-ON method" on the micro-strip seedings). In consideration of the potentiality of execution as well as the value of landscapes, the measures of treatment II could be recommendable for establishing the vegetation cover on the denuded gentle slopes in hillsides while the measures of treatment IV could be suitable for accelerating the establishment of vegetation on steeply sloping earth banks and cuts.