• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.831-835
• /
• 2007

Energy Saving is one of worldwide emerging issues. These days, applicable techniques of railway vehicle's regenerative energy are investigating in worldwide railway industries. Energy saving methods are "Downsizing energy loss" and "Re-utilizing kinetic energy". Useful plans for Downsizing energy loss are "adjusting operation table" and "optimizing running pattern". Furthermore, regenerative energy that is produced with decreasing speed and stoping, is an important element with reducing vehicle's weight, raising equipment 's efficiency, decreasing running resistance and re-configurating running pattern. Sustainable energy storage mass : Flywheel, EDLC(electrical double layer capacitor) and Secondary battery are applied in overseas, but these cases are not reported within the country. This research is reported for problems and economical validity that comes from by installing sustainable regenerative energy storage system in korean railway industries.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.2
• /
• pp.180-192
• /
• 1998

Enthalpy transport in a pulse tube was investigated by two-dimensional analysis of mass, momentum and energy equations assuming that the axial temperature gradient in the pulse tube is constant. Time-averaged second-order conservation equations of mass, momentum and energy were used to show the existence of steady mass streaming and enthalpy streaming. Effects of axial temperature gradient, velocity amplitude ratio and heat transfer between the gas and the wall on the steady mass streaming and enthalpy streaming were shown. Enthalpy loss due to the steady mass streaming is zero for basic and orifice pulse tube refrigerators, but it is proportional to the axial temperature gradient and steady mass flow rate through a pulse tube for double inlet pulse tube refrigerators.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.7
• /
• pp.33-44
• /
• 1999

Enthalpy transport in a pulse tube was investigated by two-dimensional analysis of mass, momentum and energy equations assuming that the axial temperature gradient in the pulse tube was constant. The time-averaged second-order conservation equations of mass, momentum and energy were used to show the existence of steady mass and enthalpy streaming. Effects of the axial temperature gradient, velocity amplitude ratio, and heat transfer between the gas and the tube wall On the steady mass and enthalpy streaming were shown. Enthalpy loss due to the steady mass streaming is zero for basic and orifice pulse tube refrigerators, but it is proportional to the axial temperature gradient and steady mass flow rate through a pulse tube for double inlet pulse tube refrigerators.

• Composites Research
• /
• v.27 no.2
• /
• pp.42-46
• /
• 2014

In the present study, impact tests were carried out to investigate the crashworthy behaviour of the expanded polypropylene under the constant incident energy (100 J and 200 J) with five different combinations of striker mass and velocity. Also, preliminary quasi-static test was performed to obtain basic characteristics of the expanded polypropylene. MTS 858 and Instron dynatup 9250 HV were used for the quasi-static test and impact tests, respectively. In consequence, it was found that the impact energy absorption characteristics of the expanded polypropylene was more influenced by the striker mass instead of the velocity of the striker.

• Journal of the Korean Society of Safety
• /
• v.13 no.3
• /
• pp.11-23
• /
• 1998

In this study, collapse test of thin-walled structure is performed under axially quasi-static and impact load in collapse characteristic to develop the optimum structural member for a light-oriented automobile. Furthermore, the energy-absorbing capacity is observed according to the variety of configuration(circular, square), aspect ratio in aluminum specimen to obtain basic data for the improved member of vehicle. In both quasi-static and impact collapse test, Al circular specimens collapse, in general, with axisymmetric mode in case of thin thickness while collapse with non-axisynmetric mode according to the thickness increase. For Al rectangular specimens, they collapse with axisymmetric mode in case of thin thickness, with mixed collapse mode according to the increase of thickness. In terms of initial max. load, Al square specimen turns out the best member among specimens, and then Al square, circular and circular with large scaling ratio, respectively. In case of quasi-static compression test, the absorbed energy per unit volume and mass shows higher in Al circular specimen, and then Al square, circular with large scaling ratio, respectively, according to shape ratio the absorbed energy per unit volume and mass in case of max. impact compression load is higher than that of static load. But the absorbed energy per unit volume and mass shows that Al circular specimen is the best member. Especially, unlike max. compression loan, the absorbed energy per unit volume and mass in impact test turns out the low value.

• Nuclear Engineering and Technology
• /
• v.47 no.7
• /
• pp.924-933
• /
• 2015

The correlation of the isotopic composition of uranium, plutonium, neodymium, and cesium with the burnup for high burnup pressurized water reactor fuels irradiated in nuclear power reactors has been experimentally investigated. The total burnup was determined by Nd-148 and the fractional $^{235}U$ burnup was determined by U and Pu mass spectrometric methods. The isotopic compositions of U, Pu, Nd, and Cs after their separation from the irradiated fuel samples were measured using thermal ionization mass spectrometry. The contents of these elements in the irradiated fuel were determined through an isotope dilution mass spectrometric method using $^{233}U$, $^{242}Pu$, $^{150}Nd$, and $^{133}Cs$ as spikes. The activity ratios of Cs isotopes in the fuel samples were determined using gamma-ray spectrometry. The content of each element and its isotopic compositions in the irradiated fuel were expressed by their correlation with the total and fractional burnup, burnup parameters, and the isotopic compositions of different elements. The results obtained from the experimental methods were compared with those calculated using the ORIGEN-S code.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2005.10a
• /
• pp.259-260
• /
• 2005

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.75-80
• /
• 2012

In this paper a realistic bounding method for flooding analysis following rupture of large size of thanks and piping is defined. Mass and energy release during main feedwater line break accident is analyzed with RETRAN code. It is modeled that the main feed water control valve is closed in 5.0 seconds after reactor trip. In result of the analysis, largest mass and energy is discharged at 70% reactor power. The flood sources for main feedwater room are calculated when piping failure occurs in the high energy line and medium energy line. Based on the result of flood level (1.43m), it is investigated that all of the safety-related environmental qualification equipments are well located above the flood level.

• New & Renewable Energy
• /
• v.10 no.1
• /
• pp.6-19
• /
• 2014

Organic Rankine cycle (ORC) has been widely used to convert renewable energy such as solar energy, geothermal energy, or waste energy etc., to electric power. For a small scale output power less than 10 kW, turbo-expander is not widely used than positive displacement expander. However, the turbo-expander has merits that it can operate well at off-design points. Usually, the available thermal energy for a small scale ORC is not supplied continuously. So, the mass flowrate should be adjusted in the expander to maintain the cycle. In this study, nozzles was adopted as stator to control the mass flowrate, and radial-type turbine was used as expander. The turbine operated at partial admission. R245fa was adopted as working fluid, and supersonic nozzle was designed to get the supersonic flow at the nozzle exit. When the inlet operating condition of the working fluid was varied corresponding to the fluctuation of the available thermal energy, optimal operating condition was investigated at off-design due to the variation of mass flowrate.

• The Journal of Korean Physical Therapy
• /
• v.15 no.4
• /
• pp.466-478
• /
• 2003

This study was to evaluate the body composition and bone mineral density according to aging in adult and investigated the relationship between various parameters such as body mass index(BMI), bone mineral density(BMD), bone mineral content(BMC), lean body mass(LBM), fat mass(FM) and the value obtained from dual energy X-ray absorptiometry(DEXA). The subjects were composed of healthy adult male and female who were $20^{\sim}73$ years old and they were divided three group according to age (A group : 20-39 yrs., B group : 40-59 yrs., C group : more than 60 yrs.). The conclusion derived from statistical analysis was as follows : 1. Bone mineral content and density were significantly affected by lean body mass(relatively, R=0.85 - 0.63). 2. There was significant difference among age groups in total bone mineral density. 3. There was significant difference among age groups in bone mineral content of male and female. 4. Lean body mass is diminished according to age, but there was not significant difference among age groups. 5. Fat mass of A group in male had the highest mass and followed by C group and B group. In female groups, fat mass of A group had the highest mass and followed by B group and C group. Abdominal fat mass is increased according to age. This result suggest that aging was closely relation with loss of muscle mass, bone mineral density and bone mineral content.