• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.110-115
• /
• 2012

This study describes the characteristics of combustion and exhaust emission in the special engine applying a fuel reactivity controlled compression ignition (RCCI) concept with two different energizing type (solenoid and piezoelectric) injectors for diesel injection. A diesel-gasoline mixed dual-fuel reactivity controlled compression ignition concept is demonstrated as a promising method to achieve high thermal efficiency and low emission in internal combustion engines for transportation vehicles. For investigating the combustion characteristics of RCCI, engine experiments were performed in a light-duty diesel engine over a range of injection timing and mixing rate of gasoline in mass. It was investigated that by increasing the nozzle hole diameter, increasing the combustion pressure and the net indicated mean effective pressure. $NO_x$ and soot can be reduced by advancing start of injection in 84 mixing rate of gasoline in mass. The resulting operation showed that light duty engine could achieve 48 percent net indicated efficiency and 191[g/kW-hr] net indicated specific fuel consumption with lower levels of nitrogen oxides and soot.

• Nuclear Engineering and Technology
• /
• 제48권5호
• /
• pp.1230-1236
• /
• 2016

This study aims to determine the effect of fly ash with a high replacing ratio of clay on the radiation shielding properties of bricks. Some interaction parameters (mass attenuation coefficients, half value layer, effective atomic number, effective electron density, and absorption efficiency) of clay fly ash bricks were measured with a NaI(Tl) detector at 661.6 keV, 1,173.2 keV, and 1,332.5 keV. For the investigation of their shielding behavior, fly ash bricks were molded using an admixture to clay. A narrow beam transmission geometry condition was used for the measurements. The measured values of these parameters were found in good agreement with the theoretical calculations. The elemental compositions of the clay fly ash bricks were analyzed by using an energy dispersive X-ray fluorescence spectrometer. At selected energies the values of the effective atomic numbers and effective electron densities showed a very modest variation with the composition of the fly ash. This seems to be due to the similarity of their elemental compositions. The obtained results were also compared with concrete, in order to study the effect of fly ash content on the radiation shielding properties of clay fly ash bricks. The clay fly ash bricks showed good shielding properties for moderate energy gamma rays. Therefore, these bricks are feasible and eco-friendly compared with traditional clay bricks used for construction.

• Journal of Welding and Joining
• /
• 제35권2호
• /
• pp.13-22
• /
• 2017

In laser full penetration welding process, full penetration hole(FPH) is formed as a result of force balance between the vapor pressure and the surface tension of the surrounding molten metal. In this work, a three-dimensional numerical model based on a conserved-mass level-set method is developed to simulate the transport phenomena during laser full penetration welding process, including full penetration keyhole dynamics. Ray trancing model is applied to simulate multi-reflection phenomena in the keyhole wall. The ghost fluid method and continuum method are used to deal with liquid/vapor interface and solid/liquid interface. The effects of processing parameters including laser power and scanning speed on the resultant full penetration hole diameter, laser energy distribution and energy absorption efficiency are studied. The model is validated against experimental results. The diameter of full penetration hole calculated by the simulation model agrees well with the coaxial images captured during laser welding of thin stainless steel plates. Numerical simulation results show that increase of laser power and decrease of welding speed can enlarge the full penetration hole, which decreases laser energy efficiency.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.469-472
• /
• 2008

본 연구에서는 경제성, 환경부하저감성 및 순환잔골재의 품질개선효과가 우수한 순환잔골재 건식생산기술로서 고속회전충격식 비중분리장치 및 원심력 미분말 집진장치 등으로 구성된 건식생산시스템을 개발하고 순환잔골재의 품질을 평가하여 성능을 검증하고자 한다. 그 결과 고속회전충격에 의한 순환잔골재의 파쇄작용, 원심력 및 질량차에 의한 미분말과 미세분진의 분리 및 집진작용, 질량차에 의한 미세립분의 분리 회수에 의해 표준입도, 절건밀도 등 순환잔골재의 품질개선에 효과가 있는 것으로 확인되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.809-814
• /
• 2009

Deep mixing method has been used for ground improvement and foundation system for embankment, port and harbor foundations, retaining wall, and liquefaction mitigations. It has attractive benefits because it is not only improved strength of soft ground but superior for prevention of settlement. However, the quality controls of improved mass affect to the efficiency of the deep mixing method is not properly established. These effects vary depending upon the construction environments and conditions of agitation in consideration of an agitator. The strength and shape of the improved column are not unique and these are affected by mechanical properties of agitators. In this study, in order to investigate the efficiency of deep mixing method for ground improvement on a soft clay ground, experimental studies are performed considering mechanical properties of agitator; the location of exit-hole of admixtures, an angle of mixing wing and a speed of revolution. The experiments are conducted with the simulated apparatus for deep mixing plant that reduced the scale in 1:8 of the real plant. According to the results, the diameter and shape of improved column mass vary depending on the mechanical properties and operating conditions of agitator. Its quality is better when the exit-hole of admixtures is located in the mixing wing, when an angle of mixing wing is large, and when the speed of revolution is rapid.

• 설비공학논문집
• /
• 제12권6호
• /
• pp.550-560
• /
• 2000

In order to minimize compression power and analyze the cause of exergy loss for a dry ice production cycle with 3-stage compression, the variation of compression power was investigated and the exergy analysis was peformed for the cycle. In this cycle, $CO_2$, is used both as a refrigerant and as a raw material for dry ice. The behavior of compression power and irreversibility in the cycle were examined as a function of intermediate pressure. From this result, the conditions for the minimum compression power were obtained in terms of the first stage or the third stage pressure. In addition, the irreversibilities for the cycle were investigated with respect to the efficiency of compressor. Result shows that the optimum pressure is not consistent with the conventional pressure obtained from the equal-pressure-ratio assumption. This is mainly due to the change in mass flow rate of the intermediate stage compressor by the flash gas evaporation from the flash drums. Most important is that the present exergy analysis enabled us to find bad performance components for the cycle and informed us of methods to improve the cycle performance.

• 한국가시화정보학회지
• /
• 제20권3호
• /
• pp.36-41
• /
• 2022

Drying process is involved in the production of various products including food, textiles, paper, pharmaceuticals, and batteries. Phase change of liquid to vapor generally requires enormous thermal energy, so in order to save energy, it is advantageous to develop an appropriate drier and use it under appropriate operating conditions, depending on the characteristics of materials. However, due to the complex, multiscale heat and mass transfer occurring during drying processes, predictions of appropriate drying conditions before actual operation are not easily achieved, leading to challenges in designing driers. Here, we developed a lab-scale experimental setup to evaluate the performance of band dries. The experimental setup was used to measure the moisture content and temperature change in the materials being dried in a belt dryer. Experimental results obtained using our lab-scale setup allow us to predict the performance of a full-scale band drier, thus suggesting a practical framework for predicting the drying process of various materials and developing band driers.

• Advances in aircraft and spacecraft science
• /
• 제10권3호
• /
• pp.245-256
• /
• 2023

In order to improve aerodynamic performance of multi-stage axial flow turbines used in aircraft engines, a one-dimensional aerodynamic design and optimization framework is constructed. In the method, flow path is generated by solving mass continuation and energy conservation with loss computed by the Craig & Cox model; Also real gas properties has been taken into consideration. To obtain an optimal result, a multi-objective genetic algorithm is used to optimize the efficiencies and determine values of various design variables; Final design can be selected from obtained Pareto optimal solution sets. A three-stage axial turbine is used to verify the effectiveness of the developed optimization framework, and designs are checked by three-dimensional CFD simulation. Results show that the aerodynamic performance of the optimized turbine has been significantly improved at design point, with the total-to-total efficiency increased by 1.17% and the total-to-static efficiency increased by 1.48%. As for the off-design performance, the optimized one is improved at all working points except those at small mass flow.

• Bulletin of the Korean Chemical Society
• /
• 제30권9호
• /
• pp.1996-2000
• /
• 2009

Alkali metal salts were introduced to enhance the ionization efficiency of glucose and maltooligoses in electrospray ionization-mass spectrometry (ESI-MS). A mixture of the same moles of glucose, maltose, maltotriose, maltotetraose, maltopentaose, maltohexaose, and maltoheptaose was used. Salts of lithium, sodium, potassium, and cesium were employed as the cationizing agent. The ionization efficiency varied with the alkali metal cation types as well as the analyte sizes. Ion abundance distribution of the [M+$cation]^+$ ions of the carbohydrates varied with the fragmentor voltage. The maximum ion abundance at low fragmentor voltage was observed at maltose, while the maximum ion abundance at high fragmentor voltage shifted to maltotriose or maltotetraose for Na, K, and Cs. Variation of the ionization efficiency was explained with the hydrated cation size and the binding energy of the analyte and alkali metal cation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.215-219
• /
• 2004

We reported two new techniques of barrier rib formation that are applicable to a variety of structures for high-efficiency PDPs suitable for mass-production [1]. These two methods are mold replication and direct glass sculpting. Especial progress has since been made in improving these methods to be more suitable for high-efficiency PDPs with the DelTA cell structure. This paper reports photolithographic fabrication methods for the masters used in mold replication. The masters for more complex barrier rib forms are easier to make with these methods. The paper also reports a process that combines the direct glass sculpting method with an ink-jet printing method of electrode formation.