• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.7
• /
• pp.783-790
• /
• 2017

An acceptable proximity assessment collision probability is widely considered to be less than $10^{-4}$ in maritime traffic safety audit schemes. In the 1970s, Fujii, Macduff and colleagues introduced various models for collision probability of aberrancy in the community. Although existing studies ensured acceptable proximity collision probability, around $10^{-4}$, they were constrained by assumptions. A lack of support for the proximity probability criterion has been investigated in this study for practical use. The appropriate proximity probability for different size vessels in both straight and curved lanes has been analyzed based on GICOMS data. As a result, reasonable proximity collision probabilities were determined for various vessel traffic conditions. Accordingly, necessary improvements in the maritime traffic system have been suggested in consideration for various maritime traffic situations and conditions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.519-526
• /
• 2019

This study proposes a methodology for estimating the appropriate capacity of anchorage for ports requiring the establishment of waiting anchorage and then applying the methodology to the ports in Jinhae Bay to compare it with the anchorage capacity of major ports in Korea. To estimate the appropriate anchorage capacity, the "Anchorage Capacity Index" was used, which was calculated from the "Total Gross Tonnage" and "Simultaneous Anchoring Capacity". The calculations were made according to the anchorage capacity index of 0.89 of the target harbors. The adequate anchorage capacity index for the new waiting anchorage was analyzed at a level of 6.0. If the concept of anchorage capacity index suggested in this study is reflected as a new design criteria of waiting anchorage, it will be helpful for the safety of berth, safety of anchorage and effective operation of harbor.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.396-408
• /
• 2019

The tubes which are applied in jacket platforms as the supporting structure might be collided by supply vessels. Such kind of impact will lead to plastic deformation on tube members. As a result, the ultimate strength of tubes will decrease compared to that of intact ones. In order to make a decision on whether to repair or replace the members, it is crucial to know the residual strength of the tubes. After being damaged by lateral impact, the simply supported tubes will definitely loss a certain extent of load carrying capacity under uniform axial compression. Therefore, in this paper, the relationship between the residual ultimate strength of the damaged circular tube by collision and the energy dissipation due to lateral impact is investigated. The influences of several parameters, such as the length, diameter and thickness of the tube and the impact energy, on the reduction of ultimate strength are investigated. A series of numerical simulations are performed using nonlinear FEA software LS-DYNA. Based on simulation results, a non-dimensional parameter is introduced to represent the degree of damage of various size of tubes after collision impact. By applying this non-dimensional parameter, a simplified formula has been derived to describe the relationship between axial compressive residual ultimate and lateral impact energy and tube parameters. Finally, by comparing with the allowable compressive stress proposed in API rules (RP2A-WSD A P I, 2000), the critical damage of tube due to collision impact to be repaired is proposed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.2
• /
• pp.369-376
• /
• 2021

The International Maritime Organization has developed the Energy Efficiency Design Index, an index related to carbon dioxide emissions, to enforce regulations on newly built ships. In this study, a new type of energy-saving device called the ring stator was used for 158k crude oil carriers, whose hull form was developed as a very thin after-body hull to reduce the resistance by delaying separation. The Energy-Saving Device (ESD) particularly involving the duct, is not adapted to the thin-after body hull form-like container ship. This new ring stator was developed considering these characteristics. A parametric study was conducted through Computational Fluid Dynamics (CFD) analysis using the Star-CCM+ program, and approximately 3.4 % improvement in propulsion efficiency was achieved. Further optimization investigations and experimental studies should be conducted in the future.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.1-12
• /
• 2021

The International Maritime Organization (IMO) is promoting the introduction of e-Navigation that prevents maritime accidents by fusion of Information & Communication Technology (ICT) with ship operation technology. In Korea, Korean e-Navigation is also being developed for fishing vessels and small vessels sailing offshore, which are vulnerable to maritime accidents. However, for the successful development of Korean e-Navigation, it is necessary to develop an indicator that can evaluate the development performance so that the development performance that has been progressed so far can be evaluated and the development direction can be re-established. Therefore, this study attempted to develop an evaluation index tailored to the development goal of e-Navigation service centering on the collision accident, which is a major maritime accident. In this study, a collision accident evaluation index for e-Navigation service was developed by deriving and quantifying the root cause of maritime collision accidents using Root cause analysis(RCA) and fault tree analysis (FTA) techniques. This indicator is considered to be helpful in reducing maritime accidents as it is used as a development indicator for e-Navigation and an indicator for maritime collision accident analysis.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.1
• /
• pp.85-93
• /
• 2022

In this study, we investigated how satisfaction with on-board training had an effect on career motivation of the trainees. For this purpose, satisfaction for on-board training and career motivation were used as variables. Satisfaction for on-board training were classified into education, environment and operation, and then measurement items were composed. Career motivation consisted of career identity, career insight and career resilience. To establish and test nine hypotheses, a questionnaire survey was conducted by 57 trainees who participated in the Gyeongsang National University on-board sailing training in 2021. To analyze the questionnaire responses, frequency analysis, factor analysis, multiple regression analysis and paired sample t-test were used. As a result of factor analysis, six factors for satisfaction for on-board training were derived. Among the factors, it was analyzed that satisfaction with assignments, the satisfaction with accommodation, and the satisfaction with the adequate condition of facilities and equipment had a significant effect on career motivation. In addition, it was found that career motivation significantly increased through on-board training as a result of comparing the difference between the averages of career motivation before and after on-board training.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.236-245
• /
• 2021

In this study, direct numerical and large eddy simulations of transitional flows around studs were conducted to investigate the effectiveness of turbulence stimulators at very low speeds for the minimum propulsion power condition of four knots. For simplicity, the studs were assumed to be installed on a flat plate, while the wake was observed up to 0.23 m downstream behind the second stud. For applicability to a model ship, we also studied the flow characteristics behind the first and second studs installed on a curved plate, which was designed to describe the geometry of a bulbous bow. A laminar-to-turbulent transition was observed in the wake at Re_D ≥ 921 (U_∞≥0.290 m/s), and the wall shear stress at Re_D = 1162 (U_∞ = 0.366 m/s) in the second wake was similar to that of the fully developed turbulent boundary layer after a laminar-to-turbulent transition in the first wake. At Re_D = 581 (U_∞ = 0.183 m/s), no turbulence was stimulated in the wake behind the first and second studs on the flat plate, while a cluster of vortical structures was observed in the first wake over the curved plate. However, a cluster of vortical structures was revealed to be generated by the reattachment process of the separated shear layer, which was disturbed by the first stud rather than directly initiated by the first stud. It was quite different from a typical process of transition, which was observed at relatively high Re_D that the spanwise scope of the turbulent vortical structures expanded gradually as it went downstream.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.405-430
• /
• 2021

Production planning is a key part of production management of manufacturing enterprises. Since computerization began, modern production planning has been developed starting with Material Requirement Planning (MRP), and today Enterprise Resource Planning (ERP), Advanced Planning and Scheduling (APS), Supply Chain Management (SCM) has been spreading and advanced. However, in the shipbuilding field, rather than applying these general-purpose production planning methodologies, in most cases, each shipyard has developed its own production planning system. This is because the applications of general-purpose production planning methods are limited due to the order-taking industry such as shipbuilding with highly complicated construction process consisting of millions of parts per ship. This study introduces the design and development of the production planning system reflecting the production environment of heavy shipyards in Korea. Since Korean shipyards such as Hyundai, Daewoo and Samsung build more than 10 ships per year (50-70 ships in the case of large shipyards), a planning system for the mixed production with complex construction processes is required. This study draws requirements using PI/BPR (process innovation and business process reengineering) methodology to develop a production planning system for shipyards that simultaneously build several ships. Then, CBD software development methodology was applied for the design and implementation of planning system with drawn requirements. It is expected that the systematic development procedure as well as the requirements and functional elements for the development of the shipyard production planning system introduced in this study will be able to present important guidelines in the related research field of shipbuilding management.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.4
• /
• pp.200-206
• /
• 2022

This study is to develop database by an experimental method for the development of condition based maintenance for auxiliary equipment in marine engine systems. Existing ships have been performing regular maintenance, so the actual measurement data development is very incomplete. Therefore, it is best to develop a database on land tests. In this paper, a database developed by an experimental method is presented. First, failure case analysis and reliability analysis were performed to select a failure mode. For the failure simulation test, a test bed for land testing was developed. The failure simulation test was performed based on the failure simulation scenario in which the failure simulation test plan was defined. A 1.5TB failure simulation database has been developed, and it is expected to serve as a basis for ship failure diagnosis and prediction algorithm model development.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.2
• /
• pp.355-362
• /
• 2021

To facilitate low-pressure selective catalyst reduction (L.P SCR), a high exhaust-gas temperature of a four-stroke diesel engine for a ship's generator is required. This study aimed at reducing the exhaust-gas temperature by adjusting the valve open-close timing and fuel injection timing to satisfy the operating conditions of L.P SCR and prevent accidents associated with the generator engine due to high temperature. To lower exhaust-gas temperature, the angle of the camshaft was adjusted and the shim of the fuel injection pump was added. As a result, the maximum explosion pressure increased and the average of the turbocharger outlet temperature dropped. Considering the heat loss from the turbocharger outlet to the SCR inlet, the operation condition for L.P SCR was satisfied with 290 ℃. The study demonstrates that safe operation of a diesel generator can be achieved by lowering the exhaust-gas temperature.