• KDI Journal of Economic Policy
• /
• v.43 no.1
• /
• pp.53-80
• /
• 2021

The main objective of this study is to determine whether there have been TFP increases in the Korean manufacturing sector due to trade liberalization since the 1990s. Based on the methodology proposed by Pavcnik (2002), which focuses on the channel through which trade liberalization measures enhance overall industrial productivity by triggering the exit of low-productivity firms, this study tests the following two hypotheses: first, the TFP increase in the Korean tradable industry is not higher than that in the non-tradable industry, and second, plants with lower TFP levels did not exit from the tradable industry. Through the rejection of these two hypotheses, it is possible to infer indirectly the effect of trade liberalization on firm productivity rates in Korea since the 1990s. First, this analysis reveals that since the 1990s, the TFP of the tradable sector compared to the non-tradable sector presented a statistically meaningful increase only in the 2000s, when China joined the WTO and trade increased sharply between Korea and China. Secondly, TFP growth in the tradable sector was positively affected by exits, as it was plants with lower TFP levels that ceased to exist.

• Journal of the Korean Professional Engineers Association
• /
• v.27 no.1
• /
• pp.1-4
• /
• 1994

• Journal of Environmental Health Sciences
• /
• v.3 no.1
• /
• pp.27-44
• /
• 1976

This study was carried out to evaluate the harmful factors in working environments and to investigate the labor productivity after improvement of environments, surveying 93 industrial establishments of 10 industries located in Youngdeungpo industrial area in Seoul. The results obtained were as follows: 1) The highest noise level of 125dB(A) was indicated at the rolling process of transport equipment manufacturing industry. 2) The best illumination level was shown in precise machinery industry and the worst was indicated in rubber products, metallic products and transport equipment manufacturing industries. 3) Thermal conditions were above threshold limit value (TLV) at more than two processes of all industries except printing industry. 4) The highest dust concentration was determined in textile and wearing manufacturing industry. 5) Organic solvents were detected at 52 processes in 93 industrial establishments and 33 processes of them showed higher than TLV. The results about harmful chemicals were as follows: a) sulfur dioxide ($SO_2$)was determined higher than TLV on welding process of metallic product manufacturing industry and heat treatment process of transport equipment manufacturing industry. b) Carbon monoxide (CO) concentration was 700ppm at heat treatment process of transport equipment manufacturing industry, indicating 14 times of TLV. c) vinylchloride concentration in the air of PVC raw material mixing process and PVC preparation process of chemical product manufacturing industry was determined higher than TLV. d) Hydrochloride (HCl) concentration in the air of wire expanding process of transport equipment manufacturing industry was determined higher than TLV. 7) Higher values of lead concentration than TLV were determined at lead welding metallic product manufacturing industry and type planting process of process of printing industry, $1.8mg/m^3$ and $0.3mg/m^3$ respectively. 9) 22, 968 of 52, 855 workers (i.e. 43.5%) in 93 industries were exposed to various harmful agents. 10) It was found that the improvement of illumination in electric apparatus manufacturing industry (from 20~40 lux to 420 lux) resulted in an increase in productivity of 6.5% per capita and a decrease in faulty products of 19%. 11) Improvement of environments using local exhaust ventilation system resulted in a decrease of harmful substances lower than TLV and an increase in productivity of 11.4%. 12) Improvement of shovelling tools based on ergonomics resulted in a reduction in energy expenditure of 25.3% and an increase in productivity of 32.2% per capita.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2005.05a
• /
• pp.207-214
• /
• 2005

Productivity and quality stability are very important competitive factors in PCB manufacturing lines that process the multiple types of products with the mixed process flows under frequent order information changes. MES is an appropriate IT solution to solve these problems in the medium-sized PCB manufacturing company. This paper introduces the MES development and its effects for a medium-sized PCB manufacturing company. The main functions of an implemented MES are delivery simulation, production scheduling, and production process monitoring. Productivity are improved up to $10{\sim}20%$ and manufacturing lead times per order are shortened up to 2 days according to the manufacturing scenarios.

• KDI Journal of Economic Policy
• /
• v.25 no.2
• /
• pp.3-53
• /
• 2003

Using the plant level panel data on Korean manufacturing during 1990-98 period, this study tries to assess the role of entry and exit in enhancing aggregate productivity, both qualitatively and quantitatively. Main findings of this study are summarized as follows. First, plant entry and exit rates in Korean manufacturing seem quite high: they are higher than in the U.S. or several developing countries for which comparable studies exist. Second, in line with existing studies on other countries, plant turnovers reflect underlying productivity differential in Korean manufacturing, with the "shadow of death" effect as well as selection and learning effects all present. Third, plant entry and exit account for as much as 45 and 65 percent in manufacturing productivity growth during cyclical upturn and downturn, respectively. The findings of this study show that the entry and exit of plants has been an important source of productivity growth in Korean manufacturing. Plant birth and death are mainly a process of resource reallocation from plants with relatively low and declining productivity to a group of heterogeneous plants, some of which have the potential to become highly efficient in future. The most obvious lesson from this study is that it is important to establish policy or institutional environment where efficient businesses can succeed and inefficient businesses fail.

• International Area Studies Review
• /
• v.17 no.4
• /
• pp.89-106
• /
• 2013

In this paper, we analysed the absolute and conditional convergency hypothesis and the determinants of productivity in manufacturing industries from 2000 to 2009 with 16 provinces and metro-cities by using panel analysis. In terms of convergency hypothesis test, the results show that both of the convergency hypothesis, the absolute vs. conditional hypothesis, reject the null hypothesis(H0) implying the labor productivity of the 16 province and metro-cities converged to the steady state equilibrium. Also, the speed of the absolute and conditional convergency for the 16 province and metro-cities are average 4.4% and 0.73% respectively. In addition, the results of the determinants of the labor productivity in manufacturing industry show that human capital and manufacturing location coefficient affect to the value- added per capita significantly, but government expenditure per capita doesn't affect to the value- added per capita. As for the total factor productivity, government expenditure per capita and fixed capital per capita are important factors, but research and development doesn't. Hence the government has to revise the balanced regional development policy to develop regional manufacturing industries for the vulnerable regions. Also, it requires more study regarding income disparities and productivity.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.64-65
• /
• 2014

Recently freeform buildings which are free from simple shape are implemented depending on improvement of construction method. However, freeform buildings are spent more time and cost to materialize than typical form. Because molds for production of freeform shape cannot be reused. For these reasons, low productivity, delay of construction schedule and budget overflow are occurred. Thus, technology of molds need to be developed for manufacturing of freeform concrete segments. The objective of this study is manufacturing of freeform concrete segments using rod type mold. This technology can implement not only application to various shape but also mass production. Thus, problems of construction period, productivity and cost can be solved. After this study, productivity analysis should be continued through the field application.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.87-92
• /
• 1999

The biggest challenge facing today manufacturing industry is better quality and high productivity. From an economic point of view, productivity is the most important parameter, as high productivity will reduce the cost. However, the customers of today are not only cost concerned, but also quality conscious. So high accuracy levels should also be achieved in the manufacturing process. This paper reports the development of a automatic design system based on AutoCAD program. This work is composed of three section that are design of top down menu, guide frame and gate lifter for water-gate programed by AutoLISP language and runned Windows system. The developed system ultimately generates the design for a water gate through AutoCAD program. In the design of the water gate, it needs about 23 hours with an expert, but this system can be only 80 seconds without an expert.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.333-337
• /
• 1999

The biggest challenge facing today manufacturing industry is better quality and high productivity. From an economic point of view, productivity is the most important parameter, as high productivity will reduce the cost. However, the customers of day are not only cost concerned, but also quality conscious. So high accuracy levels should also be achieved in the manufacturing process. This paper reports the development of a automatic design system based on AutoCAD program. 1'his work is composed of three section that are design of top down menu, impeller and casing for pump programed by AutoLISP language and runned Windows system. The developed system ultimately generates the design for a pump through AutoCAD program. In the design of the pump, it needs about 23 hours with an expert, but this system can be only 80 seconds without an expert.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1330-1335
• /
• 2012

This paper proposes an automatic measurement sampling method for the semiconductor manufacturing process. The method recommends sampling rates using information of process capability indexes and production scheduling plan within the restricted metrology capacity. In addition, it automatically controls the measurement WIP (Work In Process) using measurement priority values to minimize the measurement risks and optimize the measurement capacity. The proposed sampling method minimizes measurement controls in the semiconductor manufacturing process and improves the fabrication productivity via reducing measurement TAT (Turn Around Time), while guaranteeing the level of process quality.