• 조명전기설비학회논문지
• /
• 제28권5호
• /
• pp.106-114
• /
• 2014

The interior permanent-magnet synchronous motor (IPMSM) is often used for the traction motor of hybrid electric vehicles (HEVs) and electric vehicles (EVs) due to its high power density and wide speed range. This paper introduces the 120kW class IPMSM for traction motors in military trucks. This system, as a SHEV (series hybrid electric vehicle), requires a traction motor that can generate high torque. This study introduces a way to reduce costs by proposing a design approach that creates reluctance torque that can be maximized by varying the dq-axis inductance. If a model designed by a design approach meets the desired torque, the magnetic torque can be reduced by an amount equal to the increase in reluctance torque and consequently the amount of permanent magnets can be reduced. A reduction gear and high speed operation of motors are necessary for the miniaturization of the motor. Thus, a fairly large centrifugal force is generated due to the high speed rotation. This force causes mechanical interference between the rotor and the stator, and a design approach for adding an iron bridge is explained to solve the interference. In this study, the initial model and the improved model that reduces cost and improves mechanical durability are compared by FEA, and the models are produced. Finally, the FEM results were verified experimentally.

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.221-228
• /
• 2015

Colloidal particles consisted of individual nanosized magnetite grains on the surface of the silica cores were obtained by two-stage sol-gel technique. Size distribution and microstructure of the particles were analyzed using atomic force microscopy, X-ray diffraction and Nitrogen thermal desorption. Magnetic properties of the particles were studied by the method of the longitudinal nonlinear response. It has been shown that nanoparticles of magnetite have a size corresponding to a superparamagnetic state but exhibit hysteresis properties. The phenomenon was explained using the magnetostatic interaction model based on the hypothesis of iron oxide particles cluster aggregation on the silica surface.

• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.356-363
• /
• 2011

Vibrations and noise in electrical machines are directly related to the characteristics of the radial forces on one hand, and mechanical behavior on the other [1, 4]. The characteristics of these forces depend on the air gap flux density, which is also influenced by other factors, such as stator slots and poles, saturation level, winding type, and certain faults. The aim of this work is to investigate the effect of eccentricity and demagnetization faults on electromagnetic noise generated by the external surface of Permanent Magnet Synchronous Machine [PMSM]. For this purpose, an analytical electromagnetic vibroacoustic model is developed. The results confirm the effect of eccentricity and demagnetization fault in generating some low modes radial forces.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.865-866
• /
• 2006

Bearingless Switched Reluctance Motor(SRM) have combined characteristics of SRM and magnetic bearing. Production of radial force for rotor shaft magnetic suspension is explained with differential stator windings. Bearingless SRM is simple structurally because the permanent magnet does not exist and bearing does not take the influence at the environment because it does not exist and has strong torque, and loss of bearing by bearing current has the advantage not to exist. In this paper, a design method of bearingless SRM for suspension power and starting torque is proposed. The design model is implement by maxwell.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.277-279
• /
• 2000

This paper proposes two kinds of the eddy current brake which uses permanent magnet. The one, like multipolar excitation consists of hexahedron shape of a segmented permanent magnetic and iron situated in the air-gap. The other, like multipolar excitation consists of only a segmented permanent magnetic. We use a finite element method to compute the flux distribution in the model. Also, we use the Galerkin-FEM with linear interpolation function may oscillate between the adjacent nodes to calculate the braking and attraction force. The advantages of the Halbach array are discussed.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권9호
• /
• pp.891-899
• /
• 1996

A model for predicting the characteristics of elastic ferromagnetic materials having a moving gap was presented. Based on the model parameters concerning behavior of material, such as the instantaneous field intensity, attractive force between the poles, length of gap, and the induced current/ emf in the circuit can be determined from the numerical integrations of the governing equations derived. From the results of the model it is found that when dc emf is imposed on the circuit the current sharply rise and fall for very short duration then stabilize at extremely low level which depends mainly on elasticity, permeabilities and ratio of resistivity. Subsequently output emf is shown stabilized at constant value which depends on the previous parameters as well as the resistivity ratio of primary to secondary circuit after sufficient progress of time.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.250-254
• /
• 1998

Pump-storage power plants, which pumps water from the lower reservoir to the upper reservoir using the extra electronic power at night and generates the electronic power in the daytime, are more increasing. Currently it has a tendency to be high-head large-capacity machines. So in the processing of design, we need to know the vibration characteristics of pump-turbine shaft system sufficiently. In this paper, we developed the computer programs for analyzing pump-turbine shaft system considering magnetic force of generator, hydraulic force at runner, dynamic characteristics of guide bearings and the effect of add mass of water. And the superiority of this program was verified by applying it to the real model and calculating high quality critical speed, natural mode and unbalance response.

• Progress in Superconductivity
• /
• 제5권2호
• /
• pp.141-143
• /
• 2004

For designing a flywheel system using superconductor, it is necessary to understand the basic characteristics of the classical superconductor bearing. It is difficult to expect the characteristics of superconductor bearings using models that have been introduced up to now. In the "Frozen image" concept, the farce between the permanent magnet and the superconductor can be divided into two forces between permanent magnet and two imaginary magnets in the superconductor; one represents attraction farce and the other represents a repulsion force. We calculated the characteristics of two superconductor bearings, such as an axial, the radial stiffness and the levitation force. This calculation method was very helpful to expect the characteristics of the superconductor bearings. Using this model, we established the optimum condition for the superconductor bearing.r bearing.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.387-390
• /
• 2008

Electromagnetic forming (EMF) technology, which is one of the high speed forming methods, has been used for the forming process in various industry fields. Numerical approach by finite element simulation of the EMF process is presented in this study. The implicit code is used to obtain the numerical model of the time-varying currents that are discharged through the coil in order to obtain the transient magnetic forces. In addition, the body forces generated in the workpiece are used as the loading condition to analyze deformation of thin sheet metal workpiece using explicit code. Numerical approach for a dimpled shape by EMF process is carried out and the simulated results of the dimpled shape by EMF are reviewed in view of the deformed shape and formability evaluation.

• Coupled systems mechanics
• /
• 제13권1호
• /
• pp.21-41
• /
• 2024

This paper is concerned with the disturbances in a transversely isotropic new modified couple stress homogeneous thermoelastic rotating medium under the combined influence of Hall currents, magnetic fields, and mechanical sources represented by inclined loads. The application of Laplace and Fourier transform techniques are used for the derivation of analytical expressions for various physical quantities. As an application,the bounding surface is subjected to uniformly and linearly distributed force (mechanical force). Present model contains length scale parameters that can capture the size effects. Numerical inversion techniques has been used to provide insights into the system's behavior in the physical domain. The graphical representation of numerical simulated results has been presented to emphasize the impact of rotation and inclined line loads on the system, enhancing our understanding of the studied phenomena. Further research can extend this study to investigate additional complexities and real-world applications.