• Journal of the Korean institute of surface engineering
• /
• v.51 no.4
• /
• pp.202-206
• /
• 2018

Permalloy($Ni_{80}-Fe_{20}$) which is known for its soft magnetic properties is a well-known material that has been studied intensively. Permalloy nanoflakes were fabricated with the combination of electrodeposition and sonication process. Ultrasonic power was applied to the deposited alloy which produced nanoflakes in forms of sheet. High internal stress created cracks which helped the peeling of permalloy into nanosheets. Because of shape anisotropy, flakes could be aligned by magnetic field. The magnetic properties of the nanosheets were observed, and the variation of magnetic properties with the alignment of flake was also investigated.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.790-794
• /
• 1995

Differential equations governing dynamic behavior of toroid-shaped ferro-magnetic material having a small gap of uniform width were derived incorporating Maxwell equations of electromagnetic induction relevent to the system and Newtonian equation of motion. Once the external uniform magnetic field was applied within the material through dc-circuit around the toroid, gap begin to change which lead to the abrupt variation of field in the material and gap according to the differential equations already derived. Characteristics of current and electromotive force with respect to time in the circuit consisting of inductance and resistance in series could be predicted from numerical solutions of these equations. As current in the circuit increasesl, magnetic field in the material increases, thus, the gap starts to shrink due to increased attractive force between gap and elastic restoring force in the material. With an appropriate selection of elastic constant of toroidal ferromagnetic material and design of gap structure it is possible to obtain the specified in both linear and nonlinear magnetic characteristics, such as current dependent and independent inductance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.440-442
• /
• 1997

The properties of magnetic suppositories used in medicine has been tested with M ssbauer spectroscopy methods. The experiments were carried out on magnetic rectal suppositories containing parmadine and fine-dispersed ferrite powder BaO.nFe$_2$O$_3$as a magnetic filler. According to the data on the value of effective magnetic field on $^{57}$ Fe nuclei in ferrite magnetic sublattices, the stoichiometric n-number equals approximately 5.5; this vague corresponds to the composition range of optimal magnetic properties.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.304-309
• /
• 2011

A monitoring system for magnetic abrasive polishing process is necessary to ensure the polishing products the high quality and integrity. Acoustic emission (AE) signal is known to reflect the material removal phenomena in other machining processes. In a case of the magnetic abrasive polishing of non-magnetic materials, application of AE method is very difficult because of lower machining force on the surface of workpiece and the level of AE signal is extremely lower. In this study, AE sensor-based monitoring system is applied to the magnetic abrasive polishing. The relation between the level of the AE RMS and the surface roughness during the magnetic abrasive polishing of magnesium alloy steel is investigated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.313-320
• /
• 2010

The magnetic abrasive polishing (MAP) process is used to achieve the nano-meter grade polishing results on flat or complicated surface. In previous study, polishing the stainless steel plate which is a non-magneto-material was tried. To polish non-magneto-materials using the MAP process was very difficult because the process was fundamentally possible by the help of a magnetic force. Therefore, it had lower efficiency than magneto-materials such as SM45C. In this study, optimization for tool geometry of the MAP was performed to improve the magnetic force between tool and workpiece. Moreover, a permanent magnet was installed below the non-magneto-material to improve the magnetic force. And then the design of experiments was carried out to evaluate the effect of the MAP parameters on the polishing results.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.149-155
• /
• 2002

This paper presents magnetic field analysis technology that uses a vector magnetic characteristic. Recently the magnetic material was found to be measurable using the vector quantity technique. Therefore considering the anisotropy of the magnetic material in the vector field analysis is necessary. The magnetic field analysis method, which is considered the anisotropy by combining the finite element method with the E&$S^2$ (Enokizono, Soda, and Shimoji) modeling, is applied to a permanent magnet motor model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.339-341
• /
• 2007

Soft ferromagnetic materials are very useful for many sensors using magnetic materials with high permeability, low coercivity and low hysteresis loss. Among them, FeCoSiBNi amorphous magnetic films show us a good impedance change(about 3.05%/Oe, at 12MHz) by the exterior magnetic field in this experiment. These are produced by rapid solidification from the melt and the material is ejected in a jet from a nozzle and quenched in a stream of liquid. After that, we make them a shape of wire with different sizes of width. Thus, we can find that the impedance change (122.16%, at 12MHz) is occurred and the fabricated magnetic wire has the characteristics of good sensor element.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.491-498
• /
• 2001

The relationship between electrical properties of YBaCuO superconductor and externally applied magnetic field was studied to develop a magnetic field apolarity sensor. The electrical resistance of the superconductor was increased by applying external magnetic field and even after removal of the magnetic field. The behavior was related to the magnetic flux trapped in the superconductor, which penetrates through the materials by the external magnetic field. Some portion of the superconductor was changed to a normal state by the trapped magnetic flux. The appearance of the normal state yielded to enhance the electrical resistance. Electrical characteristics of the superconductor with trapped magnetic flux were extremely sensitive to the external magnetic field and showed different responses depending on the direction of the magnetic field. Considering the observed properties of the superconductor with trapped magnetic flux, a magnetic sensor was fabricated to detect simultaneously both the intensity and the direction of the magnetic field.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.575-585
• /
• 2015

Magnetic field in magnetic bearings is the physical medium to realize magnetic levitation, the distribution of the magnetic field determines the operating performance of magnetic bearings. In this paper, a thin-slice Fiber Bragg Grating-Giant Magnetostrictive Material magnetic sensor used for the air gap of magnetic bearings was proposed and tested in the condition of dynamic magnetic field. The static property of the sensor was calibrated and a polynomial curve was fitted to describe the performance of the sensor. Measurement of dynamic magnetic field with different frequencies in magnetic bearings was implemented. Comparing with the finite element simulations, the results showed the DC component of the magnetic field was detected by the sensor and error was less than 5.87%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.349-350
• /
• 2009

Superconducting magnetic bearing and rotating system were developed by utilizing the high magnetization YBaCuO superconductor. The pellets prepared by quasi-melt process had a high magnetic levitation force and a high magnetic attractive force. The shaft also could be moves its position and orientation of the rotating axis freely. Is is essential to enhance the materials properties and to improve the system design for the application of the system to industrial purpose.