• Journal of Surface Science and Engineering
• /
• v.50 no.3
• /
• pp.212-218
• /
• 2017

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classifying with an ultrasonic wet-magnetic separation unit to get high pure nano-sized particles. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders resulted in producing the powders with average size of 800 nm. The addition of a surfactant during the wet-magnetic separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 800 nm size were 3651 A/m, $53.92Am^2/kg$ and $4.0Am^2/kg$, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.2-201.2
• /
• 2016

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classified by ultrasonic wet-magnetic separation method to get nano-sized particles with high purity. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders produced the powders with average size of $3.7-0.8{\mu}m$. The addition of a surfactant during the separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 810 nm size were 45.89 Oe, 53.92 emu/gOe, 0.4 emu/Oe, respectively.

• Journal of the Korean Vacuum Society
• /
• v.18 no.4
• /
• pp.281-287
• /
• 2009

Pd was deposited on magnesium-oxide-covered magnesium ribon substrate by metal thermal evaporation method in high vacuum. The electronic and chemical properties of Pd samples with different coverages were studied using in-situ X-ray Photoelctron Spectroscopy (XPS) and Field Emission Scanning Electron Microscopy (SEM). For relatively lower amounts of Pd deposited(< 1nm), separate Pd particles could be observed, whereas at higher Pd coverages, Pd thin films caused by agglomeration of Pd nanoparticles was found. The metal support interaction with Pd-support was observed. The Pd atoms on the metal oxide/metal interface were partially negative charged by charge transfer.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.338-342
• /
• 2020

Tin oxide (SnO₂) nanocrystals are synthesized by a thermal evaporation method using a mixture of SnO₂ and Mg powders. The synthesis process is performed in air at atmospheric pressure, which makes the process very simple. Nanocrystals with a belt shape start to form at 900 ℃ lower than the melting point of SnO₂. As the synthesis temperature increases to 1,100 ℃, the quantity of nanocrystals increases. The size of the nanocrystals did not change with increasing temperature. When SnO₂ powder without Mg powder is used as the source material, no nanocrystals are synthesized even at 1,100 ℃, indicating that Mg plays an important role in the formation of the SnO₂ nanocrystals at temperatures as low as 900 ℃. X-ray diffraction analysis shows that the SnO₂ nanocrystals have a rutile crystal structure. The belt-shaped SnO₂ nanocrystals have a width of 300~800 nm, a thickness of 50 nm, and a length of several tens of micrometers. A strong blue emission peak centered at 410 nm is observed in the cathodoluminescence spectra of the belt-shaped SnO₂ nanocrystals.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.2
• /
• pp.203-208
• /
• 1997

A series of MgO-SiO2 catalysts were prepared by coprecipitation from the mixed solution of magnesium chloride and sodium silicate. Some of the sample were modified with 1 N H2SO4 and used as modified catalysts. The addition of MgO to SiO2 caused the increase of acidity and the shift of O-H and Si-O stretching bands of the silanol group to a lower frequency in proportion to the MgO content. The acid structure of MgO-SiO2 agreed with that proposed by Tanabe et al.. Catalytic activity for 2-propanol dehydration increased in relation to the increase of acidity and band shift to a lower frequency.

• The Korean Journal of Ceramics
• /
• v.3 no.4
• /
• pp.269-273
• /
• 1997

Chemical composition of cement powder influences the setting time and early compressive strength development. The setting time increases as the amounts of zinc oxide and magnesium oxide are increased. For one day compressive strength development, a cement powder with a composition 90% ZnO, 8% MgO and 2% silica resulted in the highest strength (greater than 1, 090 kg/$\textrm{cm}^2$). Cement-forming liquids also need to be buffered, with both aluminum and zinc ions, for a good consistency and a higher strength of the zinc phosphate cement. These liquids control the setting reactions.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.7
• /
• pp.786-790
• /
• 1999

Relatively inert surface of microcrystalline MgO was modified into chemically active one by carrying out controlled hydration followed by dehydration at elevated temperature under dynamic vacuum. Even though the treatment by the first cycle of hydration-dehydration did not alter the porosity of MgO, it largely enhanced surface reactivity of the MgO toward adsorbed water, turning its outer layer into brucite upon rehydration. Treatment by the second cycle of hydration-dehydration generated micropores, and slit-shaped mesopores, raising the porosity of the MgO. The overlayer of Fe2O3 of the core/shell type composite magnesium oxide enhanced this surface modification, turning its surface into more porous and more active one than that of uncoated MgO, after the treatment by the hydration-dehydration.

• Journal of Hydrogen and New Energy
• /
• v.23 no.5
• /
• pp.429-436
• /
• 2012

Mg and Mg-based alloys are regarded as strong candidate hydrogen storage materials since their hydrogen capacity exceeds that of known metal hydrides. One of the approaches to improve kinetic is addition of metal oxide. In this paper, we tried to improve the hydrogenation properties of Mg-based hydrogen storage composites. The effect of transition metal oxides, such as $Nb_2O_5$ on the kinetics of the Magnesium hydrogen absorption kinetics was investigated. $MgH_x$-5wt.% $Nb_2O_5$ composites have been synthesized by hydrogen induced mechanical alloying. The powder fabricated was characterized by X-ray diffraction (XRD), Field Emission-Scanning Electron Microscopy (Fe-SEM), Energy Dispersive X-ray (EDX), BET and simultaneous Thermo Gravimetric Analysis / Differential Scanning Calorimetry (TG/DSC) analysis. The Absorption / desorption kinetics of $MgH_x$-5wt.% $Nb_2O_5$ (type I and II) are determined at 423, 473, 523, 573 and 623 K.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.40-46
• /
• 2024

A novel approach is presented to address issues associated with the use of strong acidic solutions for the leaching of magnesium oxide (MgO) from spent magnesia-carbon refractories. An ultrasonic flotation and separation process is employed, with a mildly acidic solvent, acetic acid, used to selectively chelate MgO from the spent refractories. When using 2 M acetic acid as a solvent, the recovery of the graphite exhibited 99.7 % with high purity of 72.7 %, showing a significant improvement compared to using water as the solvent. Furthermore, the technology presented in this study offers a method for producing magnesium acetate through the reaction of MgO in spent refractory with acetic acid, providing a means for the purification and separation of graphite.

• Korean Journal of Metals and Materials
• /
• v.50 no.5
• /
• pp.375-381
• /
• 2012

Magnesium prepared by mechanical grinding under $H_2$ (reactive mechanical grinding) with transition elements or oxides showed relatively high hydriding and dehydriding rates when the content of additives was about 20 wt%. Ni was chosen as a transition element to be added. $Fe_2O_3$ was selected as an oxide to be added. Ti was also selected since it was considered to increase the hydriding and dehydriding rates by forming Ti hydride. A sample $Mg-14Ni-3Fe_2O_3-3Ti$ was prepared by reactive mechanical grinding, and its hydrogen storage properties were examined. This sample absorbs 4.02 wt% H for 5 min, and 4.15 wt% H for 10 min, and 4.42 wt% H for 60 min at n = 2. It desorbs 2.46 wt% H for 10 min, 3.98 wt% H for 30 min, and 4.20 wt% H for 60 min at n = 2. The effects of the Ni, $3Fe_2O_3$, and Ti addition, and hydriding-dehydriding cycling were discussed.