• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.189-194
• /
• 2004

As a disk drive becomes widely used in portable environments, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes In contact with outer shock disturbance, the system gets critical damage in head-gimbal assembly or disk. This paper describes analysis of a HGA(head-gimbal assembly) in micro MO drives to shock loading during both non-operating state and operating state. A finite element model which consists of the disk, suspension, slider and air bearing was used to find structural response of micro MO drives. In the operational case. the air bearing is approximated with four linear elastic springs. The commercially available finite element solver, ANSYS/LS-DYNA, is used to simulate the shock response of the HGA in micro MO drives. In this paper, the mechanical robustness of the suspension is simuiated considering the shock responses of the HGA.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.406-411
• /
• 2003

One of the trends on information storage device is focused on the development of micro-optical devices with OFH (Optical Flying Head). Many different types of sliders for OFH and optical component systems have been introduced in the literature. However, the important issue on the mechanical system, which consists of suspension, swing arm and VCM (Voice Coil Motor) part has not been discussed up to date. In this research, we analyses the suspension, which is used for the small form factor MO drive. The analysis is in process two ways. One is probabilistic analysis, another is dynamic shock analysis. Probabilistic analysis is a technique you can use to assess the effect of uncertain input parameters and assumptions on your analysis model. Using a probabilistic analysis you can and out how much the results of a finite elements analysis are affected by uncertainties in the model. Dynamic shock analysis is used for the mobile applications. The mechanical robustness of the suspension simulating the shock responses of a disk-suspension is proposed in this paper.

• 한국자기학회지
• /
• 제3권3호
• /
• pp.221-228
• /
• 1993

고밀도기록용 박막재료로서의 충족조건은 높은 보자력, 높은 포화자화, 생산성, 그리고 화학적 안정성으로써 수직자기기록매체 CoCrMo 자성박막을 RF 스퍼터링 방법으로 제조한 후, 부식 특성을 전기화학적 측정, acceleration corrosion test 및 부식후 박막의 표면분석을 통하여 조사 하였다. CoCrMo 박막의 부식특성은 스퍼터링 조건에 따라서 다르게 나타났으며, Mo의 함량이 증가 할수록 내식성은 향상되었다. 전기화학부식실험 결과 박막의 Mo 함량이 증가할수록 뚜렷한 활성- 불활성 전이를 나타내었으며 부동태전류밀도의 감소를 나타내었다. Accelerated corrosion test에 서 CoCrMo 박막의 부식은 전기화학반응에 의하여 일어났으며 Mo첨가에 따라 부식이 일어난 곳의 수는 감소하였다. AES분석결과 부식 장소에는 많은 양의 $Cl_{-}$ 이온이 존재하였고, Cr의 고갈이 부식의 원인이었다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권3호
• /
• pp.76-81
• /
• 2019

• 드라이브 ㆍ 컨트롤
• /
• 제20권1호
• /
• pp.60-62
• /
• 2023

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 춘계종합학술대회
• /
• pp.547-550
• /
• 2005

본 논문에서는 기존의 하드디스크가 가지고 있는 단점을 개선하기 위하여 반도체 소자인 Flash Memory를 이용한 ATA 버스 방식의 Flash Memory Drive를 설계 및 구현하고 성능을 평가하였다. 일반적인 하드디스크의 경우, 외부의 충격에 비교적 민감하며 이로 인해 데이터의 손상이나 디스크의 오류가 발생되게 된다. 또한 내부적인 구조로 인하여 구동 시 많은 전류를 필요로 하며 경량화에 어려움이 있다. 그러나 반도체 소자인 Flash Memory를 이용하여 하드디스크를 제작하게 되면 소전류로도 구동이 가능하며 경량화가 가능할 뿐만 아니라 특히 외부의 충격에 강하므로 자동차, 선박, 산업용과 더불어 군사용으로의 활용이 가능할 것으로 기대된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1075-1076
• /
• 2007

The HEV (Hybrid Electrical Vehicle) becomes commercialized recently because of high fuel efficiency and low air pollution. The highest output power system except the traction motor is an air conditioner compressor in HEV system. The full or hybrid electric compressor is applied for HEV. The general HEC (Hybrid Electric Compressor) requires the half power motor and drive system of the full electric compressor because the rated output power of motor drive system is designed to charge the minimum cooling capacity at the time of idle stop. Therefore, this hybrid electric is more economical and practical solution. In this paper, we studied about the motor drive system of hybrid electric compressor for HEV. The applied voltage specification is 42 V, an IPMSM (Interior Permanent Magnet Synchronous Motor) is designed and applied as the compressor drive motor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 F
• /
• pp.2213-2216
• /
• 1997

Efficient Switching of IGBT's requires fast gate drivers with high peak currents. This Paper will review the requirements for effient, reliable gate drive of IGBT's and behaviour of an IGBT switching chacteristcs. The purpose of the present paper is to investigate the switching loss mechanisms in IGBT such as MOSFETs in order to give a support to designers of IGBT gate drive circuits in selecting the more appropriate IGBTs to be used on the basics of design repuirements.

• 산업기술연구
• /
• 제18권
• /
• pp.329-334
• /
• 1998

The purpose of this study is to design and manufacture a vibration exciter, which can be used in the education and research for the vibration engineering. For this purpose, a direct drive type vibration exciter is developed, which consists of a motor, an inverter, eccentric rotating sleeves and two excitation plates. Developed exciter is tested on some dynamic characteristics to evaluate its excitation performance. Test results show that the developed machine can excite bodies on the horisontal vibrating plates in x,y direction by the constant displacement amplitude in the frequency range below 50Hz, which confirm that the exciter can be used as a vibration testing machine in the low frequency range.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 The IMAPS-Korea Workshop 2001 Emerging Technology on packaging
• /
• pp.63-92
• /
• 2001

·EC's/Japanese environmental regulation drive the Pb-free/Halogen-free application ·Most Japanese electronics companies are preparing the green products. ·All items concerning to Pb-free/halogen-free technology should be coparallely designed and developed. ·More works need to clear the unknowns on Pb-free materials ·Need of consensus on materials and standards ·EBM (Environmental Benign Manufacturing)