• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.189-194
• /
• 2004

As a disk drive becomes widely used in portable environments, one of the important requirements is durability under severe environmental condition, especially, resistance to mechanical shock. An important challenge in the disk recording is to improve disk drive robustness in shock environments. If the system comes In contact with outer shock disturbance, the system gets critical damage in head-gimbal assembly or disk. This paper describes analysis of a HGA(head-gimbal assembly) in micro MO drives to shock loading during both non-operating state and operating state. A finite element model which consists of the disk, suspension, slider and air bearing was used to find structural response of micro MO drives. In the operational case. the air bearing is approximated with four linear elastic springs. The commercially available finite element solver, ANSYS/LS-DYNA, is used to simulate the shock response of the HGA in micro MO drives. In this paper, the mechanical robustness of the suspension is simuiated considering the shock responses of the HGA.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.406-411
• /
• 2003

One of the trends on information storage device is focused on the development of micro-optical devices with OFH (Optical Flying Head). Many different types of sliders for OFH and optical component systems have been introduced in the literature. However, the important issue on the mechanical system, which consists of suspension, swing arm and VCM (Voice Coil Motor) part has not been discussed up to date. In this research, we analyses the suspension, which is used for the small form factor MO drive. The analysis is in process two ways. One is probabilistic analysis, another is dynamic shock analysis. Probabilistic analysis is a technique you can use to assess the effect of uncertain input parameters and assumptions on your analysis model. Using a probabilistic analysis you can and out how much the results of a finite elements analysis are affected by uncertainties in the model. Dynamic shock analysis is used for the mobile applications. The mechanical robustness of the suspension simulating the shock responses of a disk-suspension is proposed in this paper.

• Journal of the Korean Magnetics Society
• /
• v.3 no.3
• /
• pp.221-228
• /
• 1993

The general requirements of recording media include recording performance, environmental stability, runnability on the drive or deck, and manufacturability. CoCrMo thin films were prepared using RF sputtering system for a study on chemical stability. Surface degradation of the CoCrMo thin film was studied by SEM, XPS and AES. Surface degradation was found to be dependent of sputtering condition and Mo content. Addition of Mo to CoCr thin film improved dramatically its surface degradation resistance in dilute sulfuric acid, as indicated by active-passive transition appeared in electrochemical polarization curve. Futhermore, the passive current density was decreased with increasing Mo content. The reduction in a number density of corrosion sites by Mo addition vms observed, after accelerated corrosion test. AES survey indicated that corrosion occured on the site with Cr depletion and highly concentrated chloride ions.

• Journal of Drive and Control
• /
• v.16 no.3
• /
• pp.76-81
• /
• 2019

• Journal of Drive and Control
• /
• v.20 no.1
• /
• pp.60-62
• /
• 2023

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.547-550
• /
• 2005

This treatise studies and developed flash memory drive of ATA bus that use flash memory which is employment amount memory semiconductor to improve problem of hard-disk that is existing ATA bus. While general hard-disk is sensitive external impact or shock, but flash memory drive do save chapter as well as is strong in external impact using semiconductor memory element that disk is not low electric power, light weight possible . Practical use is expected do save chapter for embedded system or black box for vehicles, soldiers hereafter therefore.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1075-1076
• /
• 2007

The HEV (Hybrid Electrical Vehicle) becomes commercialized recently because of high fuel efficiency and low air pollution. The highest output power system except the traction motor is an air conditioner compressor in HEV system. The full or hybrid electric compressor is applied for HEV. The general HEC (Hybrid Electric Compressor) requires the half power motor and drive system of the full electric compressor because the rated output power of motor drive system is designed to charge the minimum cooling capacity at the time of idle stop. Therefore, this hybrid electric is more economical and practical solution. In this paper, we studied about the motor drive system of hybrid electric compressor for HEV. The applied voltage specification is 42 V, an IPMSM (Interior Permanent Magnet Synchronous Motor) is designed and applied as the compressor drive motor.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2213-2216
• /
• 1997

Efficient Switching of IGBT's requires fast gate drivers with high peak currents. This Paper will review the requirements for effient, reliable gate drive of IGBT's and behaviour of an IGBT switching chacteristcs. The purpose of the present paper is to investigate the switching loss mechanisms in IGBT such as MOSFETs in order to give a support to designers of IGBT gate drive circuits in selecting the more appropriate IGBTs to be used on the basics of design repuirements.

• Journal of Industrial Technology
• /
• v.18
• /
• pp.329-334
• /
• 1998

The purpose of this study is to design and manufacture a vibration exciter, which can be used in the education and research for the vibration engineering. For this purpose, a direct drive type vibration exciter is developed, which consists of a motor, an inverter, eccentric rotating sleeves and two excitation plates. Developed exciter is tested on some dynamic characteristics to evaluate its excitation performance. Test results show that the developed machine can excite bodies on the horisontal vibrating plates in x,y direction by the constant displacement amplitude in the frequency range below 50Hz, which confirm that the exciter can be used as a vibration testing machine in the low frequency range.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.07a
• /
• pp.63-92
• /
• 2001

·EC's/Japanese environmental regulation drive the Pb-free/Halogen-free application ·Most Japanese electronics companies are preparing the green products. ·All items concerning to Pb-free/halogen-free technology should be coparallely designed and developed. ·More works need to clear the unknowns on Pb-free materials ·Need of consensus on materials and standards ·EBM (Environmental Benign Manufacturing)