• ETRI Journal
• /
• v.34 no.5
• /
• pp.649-654
• /
• 2012

This paper presents a novel 16-quadrature-amplitude-modulation (QAM) E-band communication system. The system can deliver 10 Gbps through eight channels with a bandwidth of 5 GHz (71-76 GHz/81-86 GHz). Each channel occupies 390 MHz and delivers 1.25 Gbps using a 16-QAM. Thus, this system can achieve a bandwidth efficiency of 3.2 bit/s/Hz. To implement the system, a driver amplifier and an RF up-/down-conversion mixer are implemented using a $0.1{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor (GaAs pHEMT) process. A single-IF architecture is chosen for the RF receiver. In the digital modem, 24 square root raised cosine filters and four (255, 239) Reed-Solomon forward error correction codecs are used in parallel. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 21.5 dB.

• Elastomers and Composites
• /
• v.32 no.3
• /
• pp.157-165
• /
• 1997

The morphology of the thermoplastic vulcanizates prepared from ethylene-propylene-diene terpolymer, polypropylene and high density polyethylene(HDPE) or ethylene based ionomer were studied. Blends were prepared in a laboratory internal mixer where EPDM was cured in the presence of PP and HDPE or ionomer under shear with dicumyl peroxide(DCP). The effects of DCP concentration and rubber/plastics composition were studied. In the morphological analysis by scanning electron microscopy (SEM), a small amount of EPDM acted as a compatibilizer to HDPE and PP. It was also revealed that the dynamic vulcanization process could reduce the domain size of the crosslinked EPDM phase. When ionomer was added to EPDM/PP blend, the thermoplastic vulcanizate showed typical ductile fracture topology and the trend was more clearly observed when DCP contents and ionomer contents are higher.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.69.3-69.3
• /
• 2018

한국우주전파관측망(KVN, Korean VLBI Network)의 86 GHz 대역 수신기는 VLBI에서 주로 관측하는 85-95 GHz 주파수 대역에서 동작하도록 설계, 제작되었다. UMASS(University of Massachusetts) 대학으로부터 도입된 수신기의 대역폭을 84-116 GHz로 확장하기 위해 2017년도부터 수신기 설계, 부품 구입 등을 진행하고 있다.기존 수신기의 대역폭을 확장하기 위해, 협대역 주파수 변환기의 설계를 변경해야 한다. 주파수 변환기는 일반적으로 사용되는 SSB(Single Side Band) Mixer를 사용하지 않았다. 그 대신에 20 dB 이상의 높은 이미지 제거율을 갖도록 HPF(High Pass Filter)와 LPF(Low Pass Filter)를 사용하여 RF 주파수를 84-100 GHz와 100-116 GHz로 나눈 후 주파수 변환토록 하였다. 사용된 Filter의 특성을 이용, 이미지 대역 신호를 수 십 dB 이상 제거할 수 있다. RF 단에서의 신호 분리로 인해 수신기 등가잡음 온도는 수 K 정도 증가한다. 2017년에 제안된 주파수 변환기를 상온에서 구성하여 그 가능성을 검증하였고, 2018년 9월 까지 KVN W-band 수신기 1 대의 업그레이드를 진행할 것이다. 2019년까지 KVN 3 사이트의 W-band 수신기 주파수 확장을 완료할 계획이다.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.243-246
• /
• 2003

평균 입도가 $100{\mu}m$인 $Fe_{36}Co_{62}Ge_2$ 합금 분말과 $10wt\%$의 페놀계 고분자 바인더, 그리고 평균 입도가 $1.36{\mu}m$인 WC 분말을 SPEX Mixer/Mill에 넣고 8시간동안 혼합한 후 $150^{\circ}C$에서 Warm press를 이용하여 0.9 ton 의 압력으로 2시간 동안 유지하였다. VSM을 사용하여 자기적 특성을 조사한 결과 WC의 첨가량이 증가할수록 포화자화값(Ms)는 $174\~128\;emu/g$로 감소하였다. 또한 스트레인게이지를 이용하여 자기변형을 측정하였다. WC의 분포를 알아보기 위해 전자현미경으로 복합체의 단면을 관찰하였다. WC의 함량이 $10\~30wt\%$로 증가할수록 밀도와 영률(Young's Modulus) 값이 각각 $5.15\~6.27\;g/cc,\;43.5\~93.6\;GPa$ 로 증가하였다. 특히 영률은 WC를 $30wt\%$로 첨가하였을 때의 값이 첨가하지 않았을 때보다 2배 이상 증가하였다. 그러나 비자성상의 첨가로 희석효과가 나타났으며 길이 방향으로의 자기변형값$(\lambda_{ll})$과 $d_{33}$의 경우 각각 $18\%$와 $20\%$ 정도가 감소되었다. 이러한 기계적 특성의 향상은 길이 10mm의 자기변형 복합체의 공진 주파수를 71 kHz 증가시키게 되며, 따라서 초음파 진동소자용으로서의 상업적 활용범위를 증가 가능성을 제시하였다.

• Carbon letters
• /
• v.15 no.2
• /
• pp.117-124
• /
• 2014

Conductive polymer composites (CPCs) consist of a polymeric matrix and a conductive filler, for example, carbon black, carbon fibers, graphite or carbon nanotubes (CNTs). The critical amount of the electrically conductive filler necessary to build up a continuous conductive network, and accordingly, to make the material conductive; is referred to as the percolation threshold. From technical and economical viewpoints, it is desirable to decrease the conductive-filler percolation-threshold as much as possible. In this study, we investigated the effect of polymer/conductive-filler interactions, as well as the processing and morphological development of low-percolation-threshold (${\Phi}c$) conductive-polymer composites. The aim of the study was to produce conductive composites containing less multi-walled CNTs (MWCNTs) than required for pure polypropylene (PP) through two approaches: one using various mixing methods and the other using immiscible polymer blends. Variants of the conductive PP composite filled with MWCNT was prepared by dry mixing, melt mixing, mechanofusion, and compression molding. The percolation threshold (${\Phi}c$) of the MWCNT-PP composites was most successfully lowered using the mechanofusion process than with any other mixing method (2-5 wt%). The mechanofusion process was found to enhance formation of a percolation network structure, and to ensure a more uniform state of dispersion in the CPCs. The immiscible-polymer blends were prepared by melt mixing (internal mixer) poly(vinylidene fluoride) (PVDF, PP/PVDF, volume ratio 1:1) filled with MWCNT.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.16-24
• /
• 2009

Independent-gate-mode double-gate(IGM-DG) MOSFET overcomes the limitation of 3-terminal device structure, and enables to operate with different voltages for front-gate and back-gate. Therefore, circuit designs becomes not only simple, but also area-efficient due to the controllability of the 4th terminal provided by IGM-DG MOSFETs. In this paper, an RF receiver utilizing IGM-DG MOSFETs is presented and also, the circuit performance is verified by the HSPICE simulations. Besides, the circuit analysis and optimization are performed for various IGM-DG characteristics.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.281-286
• /
• 2007

In this paper, sub-circuits for 24 GHz phase locked 100ps(PLLs) using $0.5{\mu}m$ SiGe HBT are presented. They are 24 Ghz voltage controlled oscillator(VCO), 24 GHz to 12 GHz regenerative frequency divider(RFD) and 12 GHz to 1.5 GHz static frequency divider. $0.5{\mu}m$ SiGe HBT technology, which offers transistors with 90 GHz fMAX and 3 aluminum metal layers, is employed. The 24 GHz VCO employed series feedback topology for high frequency operation and showed -1.8 to -3.8 dBm output power within tuning range from 23.2 GHz to 26 GHz. The 24 GHz to 12 GHz RFD, based on Gilbert cell mixer, showed 1.2 GHz bandwidth around 24 GHz under 2 dBm input and consumes 44 mA from 3 V power supply including I/O buffers for measurement. ECL based static divider operated up to 12.5 GHz while generating divide by 8 output frequency. The static divider drains 22 mA from 3 V power supply.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.107-113
• /
• 1999

The microstructural evolution during mechanical alloying of elemental Fe and Si powders, average composition $Fe_{30}Si_{70}$ and $Fe_{50}Si_{50}$, has been investigated by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and Differential scanning calorimetry (DSC). Mechanical alloying was performed by using a SPEX 8000 Mixer/Mill under argon atmosphere with/without hexane as a process control agent (PCA). In the presence of PCA, the milling process was dominated by fracture resulting in the decrease in particle size to about $1{\mu}m$. The structural development with milling time depended on the average composition of starting powders. The mixture of $Fe_{50}Si_{50}$ and $Fe_{30}Si_{70}$ resulted in the formation of FeSi(${\varepsilon}$ - phase) and $FeSi_2$(${\beta}$ - phase), respectively. In the case of $Fe_{33.3}Si_{66.7}$, a mixture and $FeSi_2({\beta})$ was formed. These results were discussed by considering the thermodynamics and kinetics concerning the milling process.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.213-217
• /
• 2001

본 논문에서는 CPW 구조를 이용하여 60 GHz 무선 시스템 응용을 위한 V-band용 하향 주파수 혼합기를 설계 및 제작하였다. 하향 주파수 혼합기의 설계 및 제작에 있어서 GaAs PHEMT(Pseudomorphic high electron mobility transistor)를 기반으로 하였으며, 회로설계를 위해 coplanar waveguide(CPW) 라이브러리를 구축하여 이용하였다. 제작된 하향 주파수 혼합기의 변환이득은 국부발진주파수(LO) 입력이 8 dBm일 때 -8.5 dB의 최대 변환이득 특성을 얻었으며 Pl dB는 -3.3 dBm을 얻었다. 제작된 회로의 칩 크기는 1.6$\times$l.6 $\textrm{mm}^2$ 이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.11
• /
• pp.1535-1542
• /
• 2001

A high resolution digital cinematic Particle Image Velocimetry(PIV) has been developed. The system consists of a high speed CCD camera, a continuous Ar-ion laser and a computer with camera controller. To improve the spatial resolution, we adopt a Recursive Technique for velocity interrogation. At first, we obtain a velocity vector fur a larger interrogation window size based on the conventional two-frame cross-correlation PIV analysis using the FFT algorithm. Based on the knowing velocity information, more spatially resolved velocity vectors are obtained in the next iteration step with smaller interrogation windows. When the correct velocity vector at the first step is found to be critical, a Multiple Correlation Validation(MCV) technique is applied to decrease the spurious vectors. The MCV technique turns out to improve SNR(Signal to Noise Ratio) of the correlation table. The developed cinematic PIV method has been applied to the measurement of the unsteady flow characteristics of a Rushton turbine mixer. A total of 3,245 instantaneous velocity vectors were successfully obtained with 4 ms time resolution. The acquired spatial resolution corresponds to the conventional high resolution digital PIV system using a 1K ${\times}$ 1K CCD camera.