• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1065-1071
• /
• 2005

In this study, residual stress distribution in multi-stacked film by MEMS (Micro-Electro Mechanical System) process is predicted using Finite Element method (FEM). We evelop a finite element program for residual stress analysis (RESA) in multi-stacked film. The RESA predicts the distribution of residual stress field in multi-stacked film. Curvatures of multi­stacked film and single layers which consist of the multi-stacked film are used as the input to the RESA. To measure those curvatures is easier than to measure a distribution of residual stress. To verify the RESA, mean stresses and stress gradients of single and multi layers are measured. The mean stresses are calculated from curvatures of deposited wafer by using Stoney's equation. The stress gradients are calculated from the vertical deflection at the end of cantilever beam. To measure the mean stress of each layer in multi-stacked film, we measure the curvature of wafer with the left film after etching layer by layer in multi-stacked film.

• Journal of the Korean Society of Visualization
• /
• v.1 no.1
• /
• pp.28-33
• /
• 2003

This paper presents the visualization method in which 3-dimensional(3D) microchannel flow can be detected using a confocal scanning microscope. By soft-lithography, we fabricated various Bio-MEMS(Micro Electro-Mechanical System) devices such as a disposable microchip for a flow cytometer and a micro-mixer, which have 3D structures. Injecting aqueous fluorescent solution in the microfluidic devices, we measured the flow in a steady state by the confocal scanning microscope. At first, we explain the principle of the confocal scanning microscope. And then we show the results from 3D visualization of microscopic flow structures using the confocal scanning microscope.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.11
• /
• pp.1364-1370
• /
• 2019

Tilt sensors are mainly used to measure the collapse of structures such as buildings, bridges and tunnels. Recently, due to the ease of use and low price, many tilt sensors using MEMS sensors have been used, but the measurement angle range is limited, and thus, they do not have high precision for 360 degree. This is due to the inherent offset and scale errors of MEMS sensors. In this paper, we proposed an algorithm for the calculation of precision angles to reduce the mechanical error of MEMS sensors, and produced a MEMS sensor module and a transmission module to compare the angle accuracy of sensor modules before calibration and the angle measurement accuracy after calibration. Experimental results show that the proposed technique has a precision of ± 0.015 degrees for all 360-degree.

• Journal of Advanced Navigation Technology
• /
• v.23 no.3
• /
• pp.228-236
• /
• 2019

Recently, multi-sensor integration techniques have been actively studied to obtain reliable and accurate navigation solution in GPS (Global Positioning System)-denied harsh environments such as urban canyons, tunnels, and underground roads. In this paper, we propose a low-cost ultrasonic-speedometer utilizing the characteristics of the ultrasonic propagation. An efficient integrated INS (inertial navigation system)/ultrasonic-speedometer navigation system is also proposed to improve the accuracy of positioning in GPS-denied environments. To evaluate the proposed system, car experiments with field-collected measurements were performed. By the experiment results, it was confirmed that the proposed INS/ultrasonic-speedometer system bounds the positioning error growth effectively even though GPS signal is blocked more than 10 seconds and a low-cost MEMS IMU (micro electro mechanical systems inertial measurement unit) is utilized.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.387-388
• /
• 2009

Biophotonics is an emerging area in a fusion of biology and photonics, especially in advanced bioimaging, optical biosensors, photomodulation, and biochip optical read-out, and optical manipulation. This emerging area also creates many opportunities for interdisciplinary study of biology and photonics. Micro-Electro-Mechanical-System(MEMS) is an attractive technology in miniaturizing sensors and actuactors. For last decade, it has contributed to the development for active and passive small and integrated optical components in optical communication. Recently, this technology is also merging into biology for high sensitive biosensing and high resolution and fast bioimaging in small form factor. In this talk, some key advantages of small optical components and recent biophotonic MEMS achievement will be discussed for miniaturized advanced biophotonic systems.

• Transactions of Materials Processing
• /
• v.15 no.9 s.90
• /
• pp.692-696
• /
• 2006

Micro fabrication of polymeric materials becomes increasingly important. And it is considered as a low-cost alternative to the silicon or glass-based Micro Electro-Mechanical System(MEMS) technologies. In the present study, micro channels were fabricated via LiGA(Lithographie, Galvanoformung, Abformung) process used for Capillary Electrophoresis(CE) chip. Taguchi method was applied to investigate the effects of process conditions in injection molding(melt temperature, injection speed, mold temperature and packing pressure) on the transcription characteristics of the micro channel. It was found that the skin layer disturbs a formation of micro channel. Furthermore, mold temperature and injection speed were two important factors to affect the replication characteristics of micro channel.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.19-22
• /
• 2004

A numerical system to extract effective elastic properties of polycrystalline thin-films for MEMS devices is already developed. In this system, the statistical model based on lattice system is used for modeling the microstructure evolution simulation and the key kinetics parameters of given micrograph, grain distributions and deposition process can be extracted by inverse method proposed in the system. In this work, the effective elastic properties of polysilicon, $BaTiO_3\;and\;ZrTiO_4$ are extracted using this system and by employing the fraction of the potential site($f_P$) as a kinetics parameter for the microstructure evolution, the statistical tendency of these materials is studied.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.65.1-65.1
• /
• 2011

We built a simple Adaptive Optics (AO) system at laboratory. This AO system is a step toward developing AO system for astronomical use. In this step, the AO system consists of He-Ne laser as a artificial light source, wavefront sensor, MEMS (Micro electro mechanical system) type deformable mirror and several lenses. MEMS deformable mirror allows the compact system at low cost and the only several mm sized collimated beam. We made Shack-Hartmann wavefront sensor using a lenslet array and a fast frame CCD. Its performance is verified using an artificial phase disturber and noting the movement of spot images by the lenslet array. The frame rate of the driving software is about 70 fps, depending on the control parameters. The characteristics of MEMS deformable mirror was measured which includes the voltage-to-deflection relation, influence function, and cross-talk. The total system is operated under closed-loop control for the artificial phase disturber and the wavefront is found to be compensated successfully.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.914-923
• /
• 2002

Recently, there has been considerable interest in micro gyroscopes made of silicon chips. It can be applied to many micro-electro-mechanical systems (MEMS): devices for stabilization, general rate control, directional pointing, autopilot systems, and missile control. This paper shows how the mechanical design of the gyroscope can be done using axiomatic design, followed by the application of the Taguchi robust design method to determine the dimensions of the parts so as to accommodate the dimensional variations introduced during manufacturing. Functional requirements are defined twofold. One is that the natural frequencies should have fixed values, and the other is that the system should be robust to large tolerances. According to the Independence Axiom, design parameters are classified into a few groups. Then, the detailed design process is performed fellowing the sequence indicated by the design matrix. The dimensions of the structure are determined to have constant values fur the difference of frequencies without consideration of the tolerances. It is noted that the Taguchi concept is utilized as a unit process of the entire axiomatic approach.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.2
• /
• pp.153-160
• /
• 1999

Dual-stage servo system for super-high density HDD has the chances of being composed of the coarse actuator(VCM) for track-seeking control and the fine actuator(microactuator) for-following control in near future. This paper presents the concept design of dual-stage servo system and the track-following control using an electrostatic microactuator for super-high density HDD. The electrostatic microactuator is designed and fabricated by MEMS(micro-electro-mechanical system) process. Both the nonlinear plant(voltage/displacement-to-electrostatic force) and the linear plant(electrostatic force-to-displacement) of the microactuator are established. Inverse function of the nonlinear plant is employed for a feedforward nonlinear compensator design. And feedforward control effect of this compensator is shown by time-domain experiments. A track-following feedback controller is designed using the feedback nonlinear compensator which is derived from the feedforward nonlinear compensator. The track-following control experiment is done to show the control efficiency of the proposed control system. And, excellent track-following control performance(2.21kHz servo-bandwidth, 7.51dB gain margin, $50.98^{\circ}$phase margin) is achieved by the proposed control system.