• Journal of Advanced Marine Engineering and Technology
• /
• 제41권1호
• /
• pp.21-30
• /
• 2017

현재 국내에서 공장 보수용접이 가장 많이 이루어지고 있는 선박 엔진 부품은 피스톤 크라운과 배기밸브이다. 또한 선박 엔진 밸브와 크랭크 축 등의 경우에는 신규 부품에서도 성능향상을 위해 표면개질방법으로 오버레이 용접이 시공되고 있다. 용착률을 높이는 고능률 오버레이 용접 공정으로 Hot Wire GTAW, Cold Tandem GMAW, Band Arc SAW, Tandem SAW법이 개발되어 있고, 용사방법으로 PTA공정이 현장에서 많이 시공되고 있다. 입열량 제어가 용이한 공정으로 GMAW-Pulse, CMT 용접공정이 있다. 엔진 배기밸브의 보수를 위한 오버레이공정에서 열영향부에 가까운 모재 내에 액화균열이 발생하는 경우가 있어 주의를 요한다. GMAW-Pulse 공정과 CMT공정에서는 입열량 제어가 용이하여 높은 용착속도를 유지하면서도 액화균열의 발생 없이 엔진 밸브의 보수 또는 표면 개질 목적으로 시공이 가능하다. 최근에 국내에서 고능률 용접 공정으로 선박엔진의 보수 또는 표면 개질 목적으로 사용 가능한 Super-TIG 용접공정이 개발되어 있다. 이 공정은 아크를 플라즈마 스트림이라고 보고 전류증가에 따라 커지는 아크압력을 막으면서도 용가재의 용융 효율이 극대화 되도록 폭이 큰 C형의 오목한 용가재를 발명하여 용착률을 획기적으로 향상시킨 용접공정이다.

• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.24-29
• /
• 2015

The current waveform was analysed to monitor the weld quality in real time process. The acquired current waveform was discretely analysed for the top and bottom limits of peaks as well as the pulse frequency measurement. Fast Fourier Transform was implemented in the program to monitor the pulse frequency in real time. The developed algorithm or program was tested for the validation purpose. The cross-section of weld profile was compared to the current waveform profile to correlate the monitored signal and the actual parts. Pulse frequency was also used as auxiliary tool for the quality monitoring. Based on the results, it was possible to evaluate the quality of welding by measure the current waveform profile and frequency measurement.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.82-88
• /
• 2002

Simulation systems allow a close inspection of the relation between welding parameters and the resulting weld seam. These systems are very useful in education of weld staff as well as production and planning. In training the influence of variations of parameters can be investigated without the need for real welding experiments. In the design phase requirements of the welding process can be taken into account without several iteration cycles. By estimating a good parameter set for the given welding task the set up phase for a new production cycle can be reduced

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.1-14
• /
• 2002

There is a continuous development of the most common welding processes like MMA, MIG/MAG, PAW and SAW. At the same time there is a conversion from stick electrodes to solid and cored wires with an increased productivity as a result. In parallel with these changes new processes are introduced and implemented. The number of Friction Stir Welding installations is starting to grow fast Hybrid laser welding has probably made a technical break through. The Magnetic Pulse Welding process is taking off. The different mechanical joining methods; clinching and self-piercing riveting; must not be forgotten. Structural adhesive is another method to consider.

• International Journal of Korean Welding Society
• /
• 제3권1호
• /
• pp.34-38
• /
• 2003

It has been used many kinds of horizontal butt-welding methods at block-to-block erection stage in shipbuilding companies. For examples, some companies use conventional FCAW process with one side or both sides groove joint welding, others use carriage with torch holder type mechanized welding method. Although lots of efforts were done until now, some problems in quality and productivity still remain in ship's hull welding. In this study, we have attempted to raise productivity and quality on horizontal position of welding with following 3 items. 1) Prepare groove condition with no root gap for making easy fit-up work. 2) Develop improved MAG (100% $CO_2$ gas shielding) welding process with solid wire for making sound root bead from one side. 3) Develop and apply quite new automatic welding carriage. The stability of new welding process was confirmed by conducting mechanical tests of weldments to verify the soundness of weldments.

• 수산해양기술연구
• /
• 제36권4호
• /
• pp.329-336
• /
• 2000

정치망 어선에 사용하는 더블 캡스턴 드럼의 용접공정은, 순간적으로 집중투입되는 고온열원에 의해 상당 열응력과 열변형 거동이 시간의 경과에 따라 비정상적으로 발생한다. 유한요소법으로 이것들의 거동을 해석한 후 다음과 같은 결론을 얻었다. 1) 용접 초기에는 용접열원 위치에서 54∼48MPa의 상당 열응력을 나타내고, 캡스턴 드럼의 내부로 진행될수록 42∼18Mpa 정도의 열응력 분포를 보이며, 열응력 구배는 1mm당 3.6MPa의 기울기를 형성하고 있었다. 용접열원에서 0.004∼0.015mm정도의 미세한 변형량이 계산되었고 좌측 자유단으로 진행하면서 0.03∼0.033mm의 변형량은 용접초기에 열충격 현상으로 발생한 것으로 사료되므로 이에 대한 대비책이 있어야 한다. 2) 용접 중반부에서는 상당 열응력 크기는 용접 초기보다 다소 작아져서 최대 51MPa, 최소 11.3MPa을 보여주며 열응력 기울기도 다소 완화된다. 이것은 용접 열원이 이동하면서 발생하는 예열효과로 상당 열응력이 감소한 것으로 사료된다. 상당 열변형의 크기는 최대 0.04mm, 최소 0.0045mm 정도를 형성하고 있고, 용접열원의 진행으로 전체적인 변형 양상이 용접진행 방향과 동일하게 이동하고 있다. 3) 용접공정의 후반부는 상당 열변형량이 최소 0.005mm, 최대 0.045mm 정도이므로, 정밀한 용접가공을 위해 반대방향에 지그나 고정구를 설치해야 한다. 상당 열응력의 구배는 모재 내부로 진행된 양상을 보이고 있으나 열응력의 절대 크기는 최소 3MPa에서 최대 27MPa로 작아졌다. 이 것은 용접의 이동열원이 제거됨으로서 모재 내부의 열응력이 현저히 저하되었음을 의미하지만, 잔류 열응력이 존재하므로 뜨임처리와 같은 후처리가 요망된다.

• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.50-56
• /
• 2015

In general, discontinuity of metallurgical and structural points of weld zone could decline the fatigue strength. For the lightweight trend, the AHSS application in automotive chassis is in-progress. However, there are few research reports on AHSS welds fatigue strength in especially automotive chassis parts. Therefore, in this study, we evaluated the effects of the factors affecting the AHSS welding fatigue strength. As the result, the stress concentration of weld bead is the most important factor for welding fatigue strength. For the enhancement of welding fatigue strength, we focused on reducing the stress concentration of the welding beads. So, we applied and proved the plasma welding process and GTAW (Gas Tungsten Arc Welding) dressing method. It was verified by uniaxial fatigue specimen, fatigue performance increased from 40 to 60% by applying TIG dressing method compared to the conventional GMAW (Gas Metal Arc Welding). These results could be recommended the enhancement of fatigue performance of AHSS.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.42-49
• /
• 2003

The protection of steel surfaces against wear is a practical problem far agricultural, mining and manufacturing industries. Commercial processes are available in which a hard tungsten carbides rich steel layer is formed on the surface of carbon steel digging, drilling and gouging tools to improve their wear resistance. The nature of the interaction of the tungsten carbide with the steel matrix is important in determining the wear and corrosion properties of the resulting metal matrix composites(MMC). In the study, WC-12%Co/low carbon steel MMC overlays have been prepared by gas metal arc welding(GMAW) according to size of WC-12%Co grits. The characteristics wear resistance and wear mechanism have been investigated in relation to the experiment conditions each other. After MMC overlay had been tested by rubber wheel abrasion test, it was known that MMC overlay has a excellent wear resistance. Fe$_{6}$W$_{6}$C carbides of matrix in overlays were not important to restrain rubber wheal abrasion wear. Wear loss is proportioned to a applied load according to time. On the case of low load, wear occurred severely in the matrix of overlay more than WC-12%Co grit, on the contrary it is reverse on the case of high load because of fracture of WC-12%Co grits.its.

• 대한조선학회논문집
• /
• 제48권3호
• /
• pp.238-245
• /
• 2011

Welding inevitably introduces the residual stresses which affect the fatigue strength of the joint structure. The mitigation of fatigue strength depends on the residual stress magnitude and distribution. Stress relief analyses are of practical interest for all cyclic loaded welded structures, such as ships and offshore structures. In order to estimate the effects of relaxation of residual stresses in the welded structure, this paper presents a finite element analysis procedure and experimental results for the welded structure. Cruciform specimens joint by MAG welding have been tested to measure the released stress. Relieved welding residual stresses obtained by finite element analysis are compared with those measured by experiment.

• 소성∙가공
• /
• 제15권8호
• /
• pp.568-573
• /
• 2006

In order to numerically evaluate automotive hydro-formed DP-steel tubes on crash performance considering welding heat effects, the finite element simulations of crash behavior were performed for hydro-formed tubes with and without heat treatment effects. This work involves the mechanical characterization of the base material and the HAG-welded zone as well as finite element simulations of the crash test of hydro-formed tubes with welded brackets and hydro-forming of tubes. The welding heat effects on the crash performance are evaluated in efforts to improve the process optimization procedure of the engine cradle in the design stage. In particular, FEM simulations on indentations have been performed and experimentally verified for material properties of weld zone and heat affected zone.