• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.6
• /
• pp.643-651
• /
• 2001

Paddlewheel-driven circulation in a culture pond has been simulated based on the depth integrated 2 dimensional hydrodynamic model. Acceleration by paddlewheel is expressed as shaft force divided by water mass discharged by paddlewheel blades. The model has been calibrated and applied to culture ponds as following steps:- i) The model predicted velocities at every 10 m along longitudinal direction from the paddlewheel. The model was calibrated comparing the results with the measured values at mass correction factor $\alpha$ and dimensionless eddy viscosity constant $\gamma$, respectively, in a range $15\~20$ and 6. ii) Wind shear stress was simulated under conditions of direction $0^{\circ}C,\;90^{\circ}C\;and\;180^{\circ}C$ and speed 0.0, 2.5, 5.0 and 7.5 m/s. Change rate of current speed was <$1\%$ at wind in parallel or opposite direction to the paddlewheel-driven jet flow, while $4\%$ at orthogonal angle. iii) The model was then applied to 2 culture ponds located at the Western coast of Korea. The measured and predicted currents for the ponds were compared using the regression analysis. Analysis of flow direction and speed showed correlation coefficients 0.8928 and 0.6782 in pond A, 0.8539 and 0.7071 in pond B, respectively. Hence, the model is concluded to accurately predict circulation driven by paddlewheel such that it can be a useful tool to provide pond management strategy relating to paddlewheel operation and water quality.

• Journal of Astronomy and Space Sciences
• /
• v.25 no.2
• /
• pp.139-148
• /
• 2008

It has been known that high-speed solar wind streams associated with coronal holes lead to quasi-periodic substorms that occur approximately every $2{\sim}4$ hours. In this paper we examined 222 repetitive substorms that occurred during high-speed stream periods in July through December in 2003 to quantitatively determine a range of energy input from the solar wind into the magnetosphere between two consecutive substorms. For this study, we have used the Akasofu ${\varepsilon}$-parameter to time-integrate it for the interval between two consecutive substorms, and have applied this method to the 222 substorms. We find that the average amount of solar wind input energy between two adjacent substorms is $1.28{\times}10^{14}J$ and about 85% out of the 222 substorms occur after an energy input of $2{\times}10^{13}{\sim}2.3{\times}10^{14}J$. Based on these results, we suggest that it is not practical to predict when a sub storm will occur after a previous one occurs purely based on the solar wind-magnetosphere energy coupling. We provide discussion on several possible factors that may affect determining substorm onset times during high-speed streams.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.423-434
• /
• 1995

It was used boundary element method(BEM) and analysed axisymmetric problem to solve hydraulic cylinder for large vessel acting uniform internal pressure(25N/m super(2)) within elastic limit. This paper was utilized the carbon steel tubes for machine structural purposed model, inner radius was 150mm and outer radius was 250mm, axial length was semi-infinite and the isoparametric element was used. The important results obtained in this study were summarized as follows. Radial, tangential and shearing stress occured the maximum stresses(48, -20 and 34MPa) at the inner radius and the minimum stresses(32, -4 and 18MPa) at the outer radius of the hydraulic cylinder for large vessel. But negative signs have meaning compressive stress and stress diminution ratio was about 0.15MPa/mm. The use of isoparametric element raised accuracy and the increment of input data lessened the error in internal point but computer run-time was increased. The double node was improved the internal solutions to settle discontinuity at corner and the double exponential formula lessened error of stress value at boundary neighborhood. And then coincidence between the analytical and exact results is found to be fairly good, showing that the proposed analytical by BEM is reliable.

• Journal of the Korean earth science society
• /
• v.36 no.6
• /
• pp.553-566
• /
• 2015

The effects of vertical resolutions and planetary boundary layer (PBL) physics schemes in a numerical simulation with a very high resolution over the metropolitan area were investigated. The numerical experiments using the Weather Research and Forecast model were conducted from 0000 UTC 25 October to 0000 UTC 26 October 2013. We verified the numerical results against with six hourly observation data from the radiosonde at Seolleung, which was located in southern part of Seoul, and forty three auto weather systems in Seoul. In the experiments of vertical resolutions in low level atmosphere with 44, 50, and 60 layers, which are set to be subdivided particularly under 2 km height. The experiment in 60 layers, which has the highest vertical resolution in this study, showed relatively a clear diurnal variation of PBL heights. Especially, the difference of PBL heights and 10-meter wind fields were mainly seen in the area of high altitude lands for the experiments of vertical resolution. In the sensitivity experiment of PBL schemes such as asymmetric convective model-version 2 (ACM2), Yonsei University (YSU), and Mellow-Yamada-Janjic (MYJ) to the temperature, all three PBL schemes revealed lower temperature than observed profile from the radiosonde in the entire period. The experiments with YSU PBL and ACM2 PBL schemes show relatively less biased in comparison with the experiment of the MYJ PBL scheme.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.288-289
• /
• 2000

SBN, BSKNN KNSBN 등의 tungsten-bronze 계열에 속하는 광굴절 결정은 짧은 파장에서 좋은 감광도와 빠른 응답시간을 갖는다. 이중에서도 KNSBN 결정은 큰 크기의 결정 성장 및 도핑이 용이하고 광굴절 결정에서 중요한 특성 중 하나인 열 안정성(thermal stability)이 좋기 때문에 빠른 응답특성이 요구되는 응용분야에서 촉망받는 매질이다. 본 논문에서는 광정보저장, 광정보처리, 광컴퓨터, 광통신과 같은 다양한 분야에서 응용가능성을 가지는 Cu가 0.04wt.%도핑된 5mm$\times$5mm$\times$5mm 크기의 KNSBN 결정을 이용한 광신호의 증폭기술에 대하여 연구하였다. 먼저 Cu-KNSNB 결정의 2광파 결합 특성을 분석하기 위하여, 기록 파장에 따른 지수이득계수의 외부입사각의존성, 최대 지수이득계수를 나타내는 외부입사각에서 입사빔의 세기비에 따른 2광파 결합 이득을 측정하였다. 또한, 632.8nm파장 영역에서 기록 및 삭제시간 상수, 회절 효율의 입사빔 세기비 의존성을 측정하였다. 그리고, 음향-광학 변조기(AOM: acousto-optic modulator)에 의해 진폭 변조된 신호빔을 이용하여 광신호 증폭특성을 분석하고 그 결과를 제시하였다. 이때 두 빔의 입사각은 최대 지수이득계수를 나타내는 입사반각 12$^{\circ}$로 고정하고, 감쇄기를 이용하여 신호빔의 세기를 조절하면서 신호빔의 차동이득을 측정하였다. 투과된 신호빔은 같은 주파수에서 차동 이득(diffrerential gain)을 보였으며, 이는 moving grating과 시간-변조된 신호빔(또는 펌프빔)사이의 새로운 상호작용은 광굴절 결정의 시간 적분 특성에 의한 것이다. (중략) 경우는 상온에서 펌프 펄스의 유지시간이 0.5% 인 경우 레이저가 동작하는 것을 보여주었다. 이는 구조내에서 열전도가 문제가 된다는 것을 의미하는데 위아래가 공기로 둘러 싸여 있어 발생한 열이 가는 유전체 네트웍을 통해서만 전달 될 수 있기 때문이다. (중략)$^4$A$_2$에 의한 nophonon line R$_1$, R$_2$(680.4, 678.5 nm) 및 $^2$T$_1$$\longrightarrow$$^4$A$_2$(655.7, 649.3, 645.2 nm)의 형광방출 스펙트럼을 얻었으며, 형광수명은 0.264 ms로 조사되었다. 제조된 레이저 발진봉은 직경 6.3 m, 길이 45 nm이었다.\pm$0.06kHz Ge $F_4$; -1.84$\pm$0.04kHz$0.04kHz/TEX>0.04kHz 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.4
• /
• pp.1-13
• /
• 2009

Liquefaction is a significant threat to structures on loose saturated sandy soil deposits in the event of an earthquake, and can often cause catastrophic damage, economic loss, and loss of life. Nevertheless, the Korean peninsula has for a long time been recognized as a safe region with respect to the hazard of liquefaction, as the peninsula is located in a moderate seismicity region, and there have been no reports of liquefaction, with the exception of references in some historical documents. However, some earthquakes that have recently occurred in different parts of the world have led to liquefaction in non-plastic silty soils, a soil type that can be found in many of the western coastal areas of Korea. In this study, we first present procedures for evaluating the liquefaction potential, and calculate the liquefaction potential index (LPI) distribution at two western coastal sites using both piezocone penetration test (CPTu) data and standard penetration test (SPT) data. The LPI is computed by integrating liquefaction potential over a depth of 20m, and provides an estimate of liquefaction-related surface damage. In addition, we compared the LPI values obtained from CPTu and SPT, respectively. Our research found that the CRR values from CPTu were lower than those from the SPT, particularly in the range between 40 and 120 for the corrected tip resistance, (qc1N)CS, from the CPTu, or in the range of CRR less than 0.23, resulting in relatively high LPI values. Moreover, it was observed that the differences in the CRR between the two methods were relatively higher for soils with high fine contents.

• The Korean Journal of Nuclear Medicine
• /
• v.35 no.6
• /
• pp.378-388
• /
• 2001

Purpose: In this study, we developed a new method for the determination of renal depth with anterior and posterior renal scintigrams in a dual-head gamma camera, considering the attenuation factor $e^{-{\mu}x}$ of the conjugate-view method. Material and Method: We developed abdomen and kidney phantoms to perform experiments using Technetium-99m dimercaptosuccinic acid ($^{99m}Tc$-DMSA). The phantom images were obtained by dual-head gamma camera equipped with low-energy, high-resolution, parallel-hole collimators (ICONf, Siemens). The equation was derived from the linear integration of omission ${\gamma}$-ray considering attenuation from the posterior abdomen to the anterior abdomen phantom surface. The program for measurement was developed by Microsoft Visual C++ 6.0. Results : Renal depths of the phantoms were derived from the derived equations and compared with the exact geometrical values. Differences between the measured and the calculated values were the range of 0.1 to 0.7 cm ($0.029{\pm}0.15cm,\;mean{\pm}S.D.$). Conclusion: The present study showed that the use of the derived equations for renal depth measurements, combined with quantitative planar imaging using dual-head gamma camera, could provide more accurate results for individual variation than the conventional method.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.2
• /
• pp.259-266
• /
• 1998

A study on the biological and chemical characteristics in the middle last Sea of Korea was carried out at 31 stations in October $11\~18$, 1995 on board the R/V Tam-Yang. The chlorophyll a concentration, new and regenerated production, and the vertical diffusion of nitrate from the thermocline structure were investigated. From the vertical distribution of chlorophyll a, subsurface maxima were observed near the thermorline at most stations including the frontal zone, except at the southern stations where the maximum chloropyll a concentration occurred at the surface, The nanophytoplankton was the most dominant fraction comprising $83.5\%$ of total phytoplankton cell numbers, but netphytoplankton were common at the southern stations where the dominant species were Rhizosolenia sp. Nitrogenous new production and regenerated productions were measured using the stable isotope $^{15}N$ nitrate and ammonia uptake method. The vertically integrated nitrogen production varied between 8.470 and $72.945\;mg\;N\;m^{-2}\;d^{-1}$. The f-ratio, which is the traction of new production from primary production, waried between 0.03 and 0.72, indicating that $3\%$ to $72\%$ of primary production was supported by the input of nutrients from below the euphotic zone and the rest are supported by ammonia recycled within the euphotic layer. This range of f-ratio encompasses from extremely oligotrophic to eutrophic area characteristics. The differences in productivity and f-ratio among stations were related to frontal structure and the bottom topography. The values were high near the frontal zone and low outside of it, and the station near Ulleng Island showed the highest f-ratio. Vertical diffusion coefficients were calculated from both the water column stability (Kz-1) of King and Devol's equation (1979) and new nitrogen requirement (Kz-2). The values of Kz-2 ($0.11\~0.55\;cm^2/s$) were relatively low compared to the values reported previously.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.19 no.3
• /
• pp.180-190
• /
• 2014

It has been customary to exclude top 10-20% of velocity profiles in the Acoustic Doppler Current Profiler (ADCP) measurement due to side lobe effects at the boundary. To better understand the mixing in the Yeongsan estuary, the freshwater advection speed (FAS) was recovered from highly contaminated ADCP data near the surface. The velocity profiles were measured by using ADCP at two stations in the Yeongsan estuary during August 2011: one was located in front of the Yeongsan estuarine dam and the other was deployed near Goha Island. The FAS was recovered from the ADCP data set by applying rigorous post-processing methods and compared with the sediment advection speed (SAS). The SAS was determined by the peak time difference of suspended sediment concentration between two stations in the channel, divided by the distance of two stations. The FAS and the SAS showed very similar value when the freshwater discharge was greater than $2.0{\times}10^7$ ton and the SAS was a bit greater when the freshwater discharge was smaller. Since the FAS was on average about 0.8 m/s greater than the velocity at 0.8 of water depth from the bottom, the net discharge, estimated with recovered FAS and integrated over water depth and tidal cycle, was directed seaward during the high discharge contrary to the onshore direction of the net discharge estimated with 0.8 of water depth from the bottom. Moreover, the velocity shear and Richardson number changed when the FAS was used. Thus, the importance of the true FAS is appreciated in the investigation of the surface layer stability. If currents, temperature and salinity were observed for longer time in the future, it could be possible to more accurately understand the formation and decay of stratification as well as the suspended sediment transport processes.

• Journal of the Korean Society of Radiology
• /
• v.4 no.1
• /
• pp.5-9
• /
• 2010

In recent, a digital x-ray detector attracted worldwide attention and there are many studies to commercialize. There are two methods in digital x-ray detector. This method is an Indirect method and Direct method. This study is to see the differences between the digital x-ray detector based on a-Se used in the existing indirect conversion method and an x-ray conversion material that has better SNR(Signal-to-noise ratio) and property than the a-Se. To solve the problem that is difficult to make a large area film using Screen-Print method, we used a Screen-Print method. In this study, we used a polyclystal $HgI_2$ as x-ray conversion material and a sample thickness is $150{\mu}m$ and an area is $3cm{\times}3cm$. ITO(Indium-Tin-Oxide) electrode was used as top electrode using a Magnetron Sputtering System and each area is $3cm{\times}3cm$, $2cm{\times}2cm$ and $1cm{\times}1cm$ and then we evaluated darkcurrent, sensitivity and SNR of the $HgI_2$ film are measured, then we evaluated the electrical properties. And we used a current integration mode when I-V test. This experiment shows that the sensitivity increases in accordance with the area of the electrode but the SNR is decreased because of the high darkcurrent. Through fabricating of various thicknesses and optimal electrodes, we will optimize SNR in the future work.