• Tribology and Lubricants
• /
• v.28 no.2
• /
• pp.81-92
• /
• 2012

To product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive liquid package and a polymer liquid as viscosity index improver in order to improve the lubricating property of oil. That is, engine oil is the mixture of more than two fluids. In this paper, it will be systematically organized the governing equation describing non-Newtonian thermo-hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics. Then, in order to find how the thermal analysis effect on the bearing performance lubricated with the mixture of multi-fluids, it will be compared to the performances between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed journal bearing. It is found that, in the case of lower viscosity oil, the difference of pressure distribution between the above two cases turns out to be existed, even if the load capacity is same level.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.108-113
• /
• 2017

The performance of refrigerant oil at the thrust bearing and at the journal bearing of a scroll compressor is a significant factor. This paper presents the friction and anti-wear characteristics of nano-fluid with a mixture of a refrigerant oil and nano powders. The particle size distribution and oxidation stability of nano powders prepared by the electrical explosion method were analyzed by TEM and BET. It was found that the nanoparticles showed a spherical morphology with sizes ranging of 40-60 nm and were covered with graphite layers of 2-4 nm. The thermal conductivity of POE oil was 0.1-0.5W/mk higher than that of POE oil. The coefficient of friction of Cu-POE was found to be 0.1 higher than that of Al2O3. The cooling capacity of the heat pump with nanofluid increased to 3.67%, and the performance was improved by 5.83%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1308-1311
• /
• 2004

It is very important that get polishing characteristic that to be stable that accomplish planarization of high efficiency in chemical mechanical polishing, and there is repeatability Groove of pad causes much effects in flow of slurry among various factors that influence in polishing characteristic, is expected to cause change of lubrication state and polishing characteristic in contact between wafer and pad. Therefore, divided factors of pad groove by groove pattern, groove profile, groove dimensions. This research wishes to study effect that dimension of pad groove gets in polishing performance. When changed dimension (width, depth, pitch of groove) of groove, measured change of removal rate and friction force. According as groove dimension changes, could confirm that removal rate and friction force change. While result of this experiment studies effect of pad groove in CMP, it is expected to become small help.

• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2325-2334
• /
• 2023

To study the lubrication performance of tilting-pad thrust bearing (TPTBs) during start-up in nuclear pump, a hydrodynamic lubrication model of TPTBs was established based on the computational fluid dynamics (CFD) method and the fluid-structure interaction (FSI) technique. Further, a mesh motion algorithm for the transient calculation of thrust bearings was developed based on the user defined function (UDF). The result demonstrated that minimum film thickness increases first and then decreases with the rotational speed under start-up condition. The influence of pad tilt on minimum film thickness is greater than that of collar movement at low speed, and the establishment of dynamic pressure mainly depends on pad tilt and minimum film thickness increases. As the increase of rotational speed, the influence of pad tilt was abated, where the influence of the moving of the collar dominated gradually, and minimum film thickness decreases. For TPTBs, the circumferential angle of the pad is always greater than the radial angle. When the rotational speed is constant, the change rate of radial angle is greater than that of circumferential angle with the increase of loading forces. This study can provide reference for improving bearing wear resistance.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1991.11a
• /
• pp.14-21
• /
• 1991

The performance of finite journal bearing operating in turbulent regime was experimentally investigated. In order to obtain experimental data contained operating conditions(thermal deformation etc.) of bearing, this study measured the pressure and the film thickness with sensors mounted on the journal. And, the continuous pressure profile and the film thickness profile were obtained.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.341-342
• /
• 2002

Although vegetable oils provide good lubricity, they still need optimization by certain additive technology for practical applications. ZDTP improve antiwear properties of vegetable oils. However the additive performance depends on quality of the base Oil. Antioxidants were applied to prevent the auto-oxidation of vegetable oils. Good synergistic effect of anti-wear and antioxidant additives was confirmed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.269-270
• /
• 2002

Antiwear(AW) properties of phoshphonic acid derivatives for trimethylolpropane (TMP) esters were investigated under boundary conditions. AW effect of dialkyl phosphonates depends on polarity of base fluid. They provide good AW performance in less polar TMP esters, whereas their AW effect is not sufficient in polar TMP esters. Amine salts of phosphonic acid were developed as new AW additiνe system for TMP esters. They provide excellent AW performance even in polar TMP esters.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.235-240
• /
• 1998

The inlet pressure build-up at the leading edge of bearings and its effects on the static performances are investigated theoretically. The performance analyses of air-lubricated tilting pad bearings are carried out considering the inlet pressure which is obtained by means of momentum conservation method. The results show that inlet pressure is above atmosphere pressure in front of leading edge of tilting pad bearing and there is a significant influence of the inlet pressure on the performance of bearings.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.335-341
• /
• 1998

In this study, the dynamic characteritics in various loading methods for wear tester were investigated experimentally. As for the dead-weight, the pneumatic, and the hydraulic method, the load control performance against external disturbances was estimated under the several loading conditions like the different sliding speed, the varied normal load, and the misaligument. The hydraulic loading method showed the most stable loading performance of all the loading methods in the experiment.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10a
• /
• pp.55-62
• /
• 2002

Significant changes in the performance requirements of finished lubricants is having a pronounced impact on the quality and manufacturing approach for base stocks, the building block for these products. Separation processing is no longer capable of producing high yields of premium base stocks and is rapidly being replaced with hydroprocessing. Isoparaffins are the most desirable component because of their high Viscosity Index, low pour point and excellent stability. This paper will discuss industry trends and the drive towards higher quality base stocks. Manufacturing options are discussed and examples presented to demonstrate the performance of these premium base stocks.