• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 전력전자학술대회
• /
• pp.242-244
• /
• 2011

A wind generator system model includes wind model, rotor dynamics, synchronous generator, power converter, distribution line and infinite bus. This paper investigates the low-Voltage Ride-Through capability of PMSG wind turbine in a variable speed. The drive train of a wind turbine on 2-mass modeling can observe the shaft torsional vibration when the low-voltage occur. To reduce the torsional vibration when the low-voltage occur, this paper designs suppression control algorithm of the torsional vibration and implements simulation. A Matlab/Simulink is used to investigate the response during the transient state.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.340-350
• /
• 2016

A cascaded hybrid multilevel inverter including a reconfiguration technique for low voltage dc distribution applications is proposed in this paper. A PWM generation fault detection and reconfiguration paradigm after an inverter cell fault are developed by using only a single-chip controller. The proposed PWM technique is also modified to reduce switching losses. In addition, the proposed topology can reduce the number of required power switches compared to the conventional cascaded multilevel inverter. The proposed technique is validated by using a 3-kVA prototype. The switching losses of the proposed multilevel inverter are also investigated. The experimental results show that the proposed hybrid inverter can improve system efficiency, reliability and cost effectiveness. The efficiency of proposed system is 97.45% under the tested conditions. The proposed hybrid inverter topology is a promising method for low voltage dc distribution and can be applied for the multiple loads which are required in a data center or telecommunication building.

• 한국산업융합학회 논문집
• /
• 제24권1호
• /
• pp.69-77
• /
• 2021

The widely used low-cost design methodology for IoT devices is very popular. In such a networked device, memory is composed of flash memory, SRAM, DRAM, etc., and because it processes a large amount of data, memory design is an important factor for system performance. Therefore, each device selects optimized design factors such as function, performance and cost according to market demand. The design of a memory architecture available for low-cost IoT devices is very limited with the configuration of SRAM, flash memory, and DRAM. In order to process as much data as possible in the same space, an architecture that supports parallel processing units is usually provided. Such parallel architecture is a design method that provides high performance at low cost. However, it needs precise software techniques for instruction and data mapping on the parallel architecture. This paper proposes an instruction/data mapping method to support optimized parallel processing performance. The proposed method optimizes system performance by actively using hardware and software parallelism.

• 전자공학회논문지C
• /
• 제34C권11호
• /
• pp.12-19
• /
• 1997

In this paper, we present a logic synthesis algorithm for low powr design fo combinational circuits. The proposed algorithm reduces power dissipation by eliminating unnecessary signal transitions. The proposed algorithm restructures a given circuit by using a kernel as prediction logic in a precomputation-based scheme such that switching activity of circuit can be minimized. Experimental results show that the system is efficient for low power design of combinational circuits.

• 전력전자학회논문지
• /
• 제22권3호
• /
• pp.223-230
• /
• 2017

A low-cost BLDC motor with hall sensor is used to drive the position control of a facility security monitoring system in this paper. Low measurable frequency of the hall sensor signal in low-speed regions results in difficulty in obtaining accurate speed detection and position control. To improve system control performance, we propose a variable gain of position controller and stop mode control scheme according to the motor speed and error position with pre-set deceleration time. The proposed stop mode control scheme is activated around the stop position to forcibly move the BLDC motor to the stop position in low speed. In the proposed stop mode, the motor current is controlled by the actual speed with the reference rotating angle. The control performance of the proposed position control is verified through experiments at the actual rail guided facility security monitoring system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.69-74
• /
• 2004

System-on-glass technology made with low temperature poly-Si TFT has been rapidly advancing in recent years. We have developed a low-power, narrow edged frame, 1.9inch system-on-glass LCD which fully integrates a 16-bit RGB interface driver and all power circuits required for driving the LCD. In this paper, the latest poly-Si TFT circuit technologies used in the newly developed LCD are discussed. The development trends are also reviewed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1060-1061
• /
• 2015

This paper presents the control method of MPPT (Maximum Power Point Tracking) using back-to- back converter. The windturbine system use PMSG(ermanent Magnet Synchronous Generator) system considering low maintenance costs and driving performance at low wind. This paper use the adaptive sliding mode control to the torque control. Proposed method was analyzed mathematically.

• Journal of information and communication convergence engineering
• /
• 제5권4호
• /
• pp.358-361
• /
• 2007

We report on a new type dc-dc converter design that combines the advantage of dc ripple noise elimination and high efficiency. As potential low cost solar cells, DSC module and the panel's system efficiency and stability are still critical problems to the way of marketing. In this study, a new three-step dc-dc converter scheme with the phase-shift-carrier technology is proposed to apply for solar power system. We have achieved power conversion efficiency around 94.88%.

• 한국항행학회논문지
• /
• 제22권4호
• /
• pp.319-324
• /
• 2018

본 논문은 RF 전력 반도체를 사용한 고출력 전력증폭기를 구현한 것으로 기존의 플라즈마 발생 장치에 사용되는 마그네트론 방식의 고출력 증폭기 문제점인 낮은 효율과 짧은 수명, 유지 보수의 어려움 그리고 높은 운용비용 등을 개선하기 위한 것이다. 구현된 고출력 전력증폭기는 2.45 GHz ISM (industrial scientific medical) 대역에서 공간 결합방식을 이용한 저 손실, 고출력 레디알 결합기와 반도체로 3 kW급 출력을 얻기 위해서 300 W 급 전력 증폭기 16개의 증폭기로 구성되어 있다. 또한, 이 증폭기는 개별적인 증폭기에 수냉 방식의 구조를 적용하여 고출력에 따른 발열문제를 극복하였다. 소형 시스템으로 구성된 이 전력증폭기는 원하는 출력에서 50%의 높은 효율을 얻었다.

• 한국컴퓨터정보학회논문지
• /
• 제26권11호
• /
• pp.11-19
• /
• 2021

본 논문은 충전식 배터리의 단점을 보완하여 급속 충전과 방전이 가능하고 높은 전력 효율 및 반영구적인 충·방전 사이클 수명의 특성을 갖는 수퍼커패시터를 보조 전력 저장장치로 사용하여 전력 관리 시스템에 결합한 프로토타입 플랫폼을 제안한다. 본 논문의 플랫폼을 위해 물리적인 환경 변화에 따른 태양광 패널에서의 공급 전력 차단 혹은 재개 상태를 마이크로컨트롤러에 연결된 인터럽트를 통해 감지할 수 있는 기법을 개발하였다. 연속적인 전원 공급이 보장되지 않는 컴퓨팅 환경에서 데이터의 유실을 방지하기 위해 전원 공급이 차단되는 경우 휘발성 메모리에 있는 프로그램 문맥 및 데이터를 비휘발성 메모리로 이전하는 낮은 수준의 시스템 소프트웨어를 마이크로컨트롤러에 구현하였다. 실험을 통해 슈퍼커패시터가 보조 전력 저장장치로서 일시적 전원 공급에 효과적으로 하는지를 검증하였으며 다양한 벤치마크를 통해 전원 상태 감지 및 휘발성 메모리에서 비휘발성 메모리로의 프로그램 문맥 및 데이터의 이전 기법이 낮은 오버헤드를 갖음을 확인하였다.