• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.632-638
• /
• 2002

Electron beam (EB) and Gas tungsten arc (TIG) welds were performed on 12.7 mm thick Ti-6Al-4V plate (ASTM Titanium Grade 5). Charpy-V toughness and hardness, as well as, microstructure of the welds and penetration from the macrostructure were studied. It appears that by EB welding rather smaller $\beta$-grains than with TIG welding can be obtained. Next to the fusion line the $\beta$-grain size in the HAZ was 50 ${\mu}{\textrm}{m}$l while in the weld metal it was 150 ${\mu}{\textrm}{m}$. Charpy-V toughness of the EB weld metal was equal or even better to that of base metal, which shows that the $\alpha$-martensite per se is not particularly brittle if only the grain size is fine enough. This is similar to behavior of low carbon martensite in steel. The grain size was studied with light optical and scanning electron (SEM) microscopes. Thus for products, for products which can be manufactured automatically with very narrow fit, the EB welding of Ti-6Al-4V appears to yield satisfactory toughness without any complex post weld heat treatment. ill this study as in earlier studies the TIG welds gave lower toughness than that of the base material due to the higher heat input and slower cooling as compared to EB welding.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.119-122
• /
• 2012

Circulating fluided bed(CFB) furnace which can use a variety of low-grade fuels because of high heat capacity and good mixing characteristic in its furnace have turned out to be effective system. There is no many research to predict performance considering total boiler system with water-steam side. Most of performance prediction model have focused on hydrodynamics or chemical mechanism in furnace. so, This study is aimed to develop performance prediction model which consider water-steam side.

• 대한기계학회논문집B
• /
• 제35권12호
• /
• pp.1343-1349
• /
• 2011

본 연구에서는 $100^{\circ}C$의 저온 열원을 이용하여 구동되는 랭킨 동력 사이클에 대하여, HFC-134a를 이용한 아임계 운전을 할 경우의 출력과 HFC-125 를 이용한 초월임계 운전을 할 경우의 출력을 서로 비교함으로써, 초월임계 운전에 의한 출력 향상 가능성을 연구하였다. 서로 다른 두 사이클들의 출력을 공정하게 비교하기 위하여, 각 사이클들을 3 개의 설계인자를 이용하여 최적화 하였다. 이 때, 보다 현실적인 결과를 위하여 기존의 연구와는 달리, 열교환 과정에서 작동유체의 열전달 및 압력강하 특성을 고려하였다. 시뮬레이션 결과, HFC-125 초월임계 사이클의 출력이 HFC-134a 아임계 사이클의 출력에 비해 본 연구의 시뮬레이션 조건 하에서 9.4% 향상 될 수 있음을 보였다.

• 한국연초학회지
• /
• 제7권1호
• /
• pp.49-55
• /
• 1985

low grade leaves of flue-cured (N.C. 2326) and air-cured (Br 21) have been heated at $140^{\circ}C$ for 10 and 20 minutes, respectively. As heating duration increased, each contents of nicotine, total nitrogen, total sugar and free amino acid decreased in both leaves. The result obtained from this experiment are as following 1. Nicotine content decreased in both leaves. Heating for 10 and 20 minutes showed respectively nicotine decrease of 13.2% and 21.6% for Br 21 and 8.2% and 13.2% for N.C.2326. Decrease of total nitrogen and total sugar was inversely proportional to the heating duration. N.C. 2326 in the decrease out numbered Br.21 by the ratio 2: 1 for 10min.-heating, and 5:4 for 20 min.-heating. 3. Total free amino acid was decrease by 17.1% and 13.85 for N.C. 2326 and Br 21, respectively when heated for 10 min., and 25.6% and 26.5% respectively when heated for 20 min. When sucrose was added to Br 21, th decrease ratio of total free amino acid of Br.21 was increased. It is suggested that the addition of sucrose could promote the browning reaction in Br 21 leaves.

• 한국암석학회:학술대회논문집
• /
• 한국암석학회 2006년도 동계학술심포지엄
• /
• pp.43-60
• /
• 2006

The Yeongnam Massif, one of Precambrian basements in Korean Peninsula, is characterized by widespread occurrence of low-pressure/high-temperature (LP/HT) schists and gneisses accompanying extensive anatexis and granitic magmatism. Metapelitic mineral assemblages define three progressive metamorphic zones pertinent to low-pressure facies series: cordierite, sillimanite and garnet zones with increasing temperature. Metamorphic grade ranges from lower amphibolite to lower granulite facies and metamorphic conditions reach ca. 750-800 C and 4-6 kbar in migmatitic gneisses. Migmatitic gneisses are prominent in the sillimanite and garnet zones. Textural and petrogenetic relationshipsin leucosome suggest that migmatitic gneiss is the product of anatexis of metasedimentary rocks. The migmatite formation during the prograde metamorphism is governed initially by fluid-present melting and subsequently by biotite-dehydration melting. The large amount of leucosomes in the sillimaniteand garnet zones can be explained by the fluid-present molting possibly triggered by an external supply of aqueous fluid. Field and geochronologic relationships between leucogranites and migmatitic gneisses further suggest that leucogranite has providedfluid and heat required for widespread migmatization.

• 한국유체기계학회 논문집
• /
• 제18권4호
• /
• pp.13-21
• /
• 2015

The system design of the Organic Rankine Cycle(ORC) is greatly influenced by the thermal properties such as the temperature or the thermal capacity of heat source. Typically waste heat, solar energy, geothermal energy, and so on are used as the heat source for the ORC. However, thermal energy supplying from these kinds of heat sources cannot be provided constantly. Hence, an experimental study was conducted to utilize fluctuating thermal energy efficiently. For this experiment, an impulse turbine and supersonic nozzles were applied and the supersonic nozzle was used to increase the velocity at the nozzle exit. In addition, these nozzles were used to adjust the mass flowrate depending on the amount of the supplied thermal energy. The experiment was conducted with maximum three nozzles due to the capacity of thermal energy. The experimented results were compared with the predicted results. The experiment showed that the useful output power could be producted from low-grade thermal energy as well as fluctuating thermal energy.

• 한국수소및신에너지학회논문집
• /
• 제26권3호
• /
• pp.278-286
• /
• 2015

This paper presents the analytical results of the thermodynamic performance characteristics for a cogeneration system using regenerative organic Rankine cycle (ORC) driven by low-grade heat source. The combined heat and power cogeneration system consists of a regenerative superheated ORC and an additional process heater in a series circuit. Eight working fluids of R134a, R152a, propane, isobutane, butane, R245fa, R123, and isopentane are considered for the analysis. Special attention is paid to the effect of turbine inlet pressure on the system performance such as thermal input, net power and useful heat productions, electrical, thermal, and system efficiencies. The results show a significant effect of the turbine inlet pressure and selection of working fluid on the thermodynamic performance of the system.

• 한국유체기계학회 논문집
• /
• 제17권1호
• /
• pp.12-21
• /
• 2014

An organic Rankine cycle was analyzed to work at the optimal operating point when the heat source is fluctuated. R245fa was adopted as a working fluid, and an axial-type turbine as expander on the cycle was designed to convert the heat energy to the electricity since the turbo-type expander works at off-design points better than the positive displacement-type expander. A supersonic nozzle was designed to increase the spouting velocity because a higher spouting velocity can produce more output power. They were designed by the method of characteristics for the operating fluid of R245fa. Three different cases, such as various spouting velocities, various inlet total temperatures, and various nozzle numbers, were studied. From these results, an optimal operating cycle can be designed with the organic Rankine cycle when the available heat source as renewable energy is low-grade temperature and fluctuated.

• 한국재료학회지
• /
• 제25권11호
• /
• pp.607-611
• /
• 2015

The microstructural evolution of Grade 91 tempered martensite ferritic steels heat treated at $760{\sim}1000^{\circ}C$ for two hours was investigated using scanning electron microscopy(SEM), energy disperse spectroscopy(EDS), electron backscattered diffraction (EBSD), and transmission electron microscopy(TEM); a microhardness tester was also employed, with a focus on the grain and precipitate evolution process as well as on the main hardening element. It was found that an evolution of tempered martensite to ferrite($760{\sim}850^{\circ}C$), and to fresh martensite($900{\sim}1000^{\circ}C$), occurred with the increase of temperature. Simultaneously, the parabolic evolution characteristics of the low angle grain boundary(LAGB) increased with the increase of the heating temperature(highest fraction of LAGB at $925^{\circ}C$), indicating grain recovery upon intercritical heating. The main precipitate, $M_{23}C_6$, was found to be coarsened slightly at $760{\sim}850^{\circ}C$; it then dissolved at $850{\sim}1000^{\circ}C$. Besides this, $M_3C$ cementite was formed at $900{\sim}1000^{\circ}C$. Finally, the experimental results show that the hardness of the steel depended largely on the matrix structure, rather than on the precipitates, with the fresh martensite showing the highest hardness value.

• 생명과학회지
• /
• 제22권11호
• /
• pp.1523-1528
• /
• 2012

육질 등급에 차이를 보이는(3등급과 1++등급) 한우 등심육을 대상으로 한 단백체 연구를 통해 heat shock protein beta 1 (HSPB1)의 발현 차이가 관찰되었다. 따라서 본 연구는 HSPB1의 유전자와 단백질 수준에서의 발현이 육질에 중요한 요인으로 작용하는 연도(전단력)에 미치는 영향을 규명하기 위하여 수행하였다. 전단력 값의 차이를 보이는 동기우 집단 20두를 대상으로 유전자 및 단백질의 발현량을 분석하였고, 통계분석을 수행하였다. 유전자 및 단백질 수준에서의 발현량을 분석한 결과 HSPB1은 전단력이 낮은 그룹에서 전단력이 높은 그룹보다 2배 발현이 높은 것으로 확인되었으며(p<0.05), 전단력과의 관련성 분석 결과에서도 유전자와 단백질 발현량 모두에서 통계적 유의성이 확인하였다(p<0.05). 이러한 결과로 볼 때 HSPB1 유전자는 한우 등심육의 연도와 밀접히 관련되어 있다고 판단되며, 지속적으로 유전자구조 변이연구 등을 통해 유전자 마커로의 개발이 필요할 것으로 생각된다.