• 한국세라믹학회지
• /
• 제41권1호
• /
• pp.51-56
• /
• 2004

$Al(OH)_3$, 비정질 $SiO_2$, $AIF_3$를 출발원료로 기상-고상 반응을 통해 $1100^{\circ}C$의 저온에서 뮬라이트 휘스커를 합성하였다. $800^{\circ}C$ 온도부근에서 협상의 플루오르토파즈의 생성이 관찰되었으며, $1000^{\circ}C$부터 토퓨ㅏ즈의 분해갸 시작되어 $1100^{\circ}C$ 이상의 온도에서는 전량 뮬라이트가 관찰되었다. $1200^{\circ}C$에서 합성된 뮬라이트 휘스커는 성장 방향이 [001] 방향이었으며, 성장방향에 평형한 면은 {110}면이었다. {110}면사이의 면간 거리는 $5.34^{\AA}C$이었으며, 뮬라이트를 이루는 $Al_2O_3$의 함유량은 73.56wt%이었다.

• 한국동물학회지
• /
• 제14권2호
• /
• pp.75-84
• /
• 1971

Genetic analysis of a new wing mutant, Surf wings (Srf), was performed. Mutant flies were extracted from a wild population of Drosophila melanogaster at the vicinity of Atomic Energy Research Institute, Seoul in August-September 1969. 1. The distal half of wings of heterozygotes (Srf/+) turned upwards about 40 degree from body axis, but flying ability was not disturbed. They overlap Cy in low frequency when they are grown below $22^{\circ}C$. This resembles with Si or j series, but wing margins are not rolled and diversed. Postscutellars are erected slightly, but they, in general, are not crossed. Any other external pleiotropic effects were not observed. 2. Penetrance and expressivity of both sexes are not complete. Their extents are variable with sex and temperature. These characters show maximum tendencies when the development is made at $22^{\circ}C$ (female: P = 0.996, E = 0.932, male:P = 0.961, E = 0.698). 3. The preliminary locus of Srf was determined to be 66.8 on the right arm of second chromosome by using recessive maker gene cn bw. 4. The homozygous flies(Srf/Srf) have shown perfect lethality. The heterozygotes (Srf/+), on the other hand, have shown to be viable and fertile. Srf chromosomes are kept in a balanced lethal system with Pm chromosomes which are associated with inversions. Hence, it is partially reasonable to suppose that Srf may persist in a natural population by the same mechanism. 5. Allelism test with Cy was also conducted. The fact that combination with Cy in the trans-phase (+ Srf/Cy +) is viable in contrast to the lethality of Srf/Srf and Pm/Pm indicates that Srf and Cy are not functionally allelic.

• Macromolecular Research
• /
• 제17권9호
• /
• pp.658-665
• /
• 2009

This study examined the effects of the sodium salts of aliphatic dicarboxylic acids (DCAs) on the dynamic mechanical properties and morphology of two sets of poly(styrene-co-sodium methacrylate) (MNa) and poly(styrene-co-sodium styrenesulfonate) (SNa) ionomers. When the DCA content was relatively low, the ionic moduli of the MNa and SNa ionomers increased but the matrix and cluster glass transition temperature ($T_g$) did not change significantly. The increasing ionic modulus was almost independent of the type of the ionic groups of the ionomer, and the chain length of DCAs. When a large amount of the sodium succinate (DCA4) was added to the MNa and SNa ionomers, the ionic moduli of the two ionomers increased strongly but the matrix and cluster $T_g's$ increased slightly and significantly, respectively. In the case of sodium hexadecanedioate (DCA 16), DCA 16 increased the ionic moduli of the two ionomers. The addition of DCA16 changed the matrix and cluster $T_g's$ of the MNa ionomer slightly, but decreased the cluster $T_g$ of the SNa ionomer significantly with no change in the matrix $T_g$. In addition, the DCA-containing ionomers showed an X-ray diffraction peak indicating the presence of ordered domains of DC As in the ionomers. Hence, DCA4 acts mainly as a reinforcing filler in MNa and SNa systems. In the case of DCA 16, it initially behaved like a filler but also functioned as a preferential plasticizer for the clusters at high content.

• 한국식품과학회지
• /
• 제29권5호
• /
• pp.987-991
• /
• 1997

솔비톨의 형태와 입자크기가 무설탕 츄잉껌의 텍스쳐에 미치는 영향을 살펴보기 위하여 두 가지 형태인 치밀한 구조를 지닌 P-type과 듬성한 구조를 지닌 S-type의 솔비톨과 50 mesh와 100 mesh의 솔비톨을 사용하였다. 츄잉껌에 사용한 솔비톨 형태는 S-type이 P-type보다 더 유연하였고, 50 mesh의 솔비톨 보다 100 mesh가 더 유연하였다. 솔비톨의 강도는 S-type보다 P-type에서 컸으며 50 mesh보다 100 mesh에서 크게 나타났다. 이것은 덜 치밀한 구조를 지닌 솔비톨이 사용된 무설탕 츄잉껌이 높은 유연성과 낮은 강도를 보여 줌을 의미하고 입자의 크기가 작은 솔비톨을 사용할수록 무설탕 츄잉껌의 유연성과 강도가 증가됨을 의미한다. 그러므로 본 실험에서는 유연성이 높고 강도가 상대적으로 낮은 S-type의 솔비톨을 무설탕 츄잉껌의 원료로 선택하였다. 선택한 S-type 솔비톨이 함유된 무설탕 츄잉껌의 솔비톨의 입자크기에 따른 유연성과 강도를 측정한 결과 80 mesh 입자가 츄잉껌의 고체상 원료로 적합하였다. 80 mesh의 S-type 솔비톨이 함유된 무설탕 츄잉껌의 온도변화에 따른 유연성과 강도를 측정하였다. 실험 결과 온도가 증가할수록 무설탕 츄잉껌의 유연성은 증가하였으나 강도는 감소하였다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.936-936
• /
• 2006

Bulk amorphous materials have been intensively studied to apply for various advanced industry fields due to their high mechanical, chemical and electrical properties. These materials have been produced by several techniques such as mechanical alloying, melt spinning and gas atomization, etc. Among them, the atomization is the most potential technique for commercialization due to high cooling rate during solidification of the melt and mass productivity. However, the amorphous powders still have some limitations because of their low ductility and toughness. Therefore, intensive efforts have to be carried out to increase the ductility and toughness. In this study, the Ni-based amorphous powder was produced by the gas atomization process. And in order to increase the ductile toughness, ductile Cu phase was coated on the Ni amorphous powder by spray drying process. The characteristics of the as-synthesis powders have been examined and briefly mentioned. The master alloy with $Ni_{57}Zr_{20}Ti_{16}Si_2Sn_3$ was prepared by vacuum induction melting furnace with graphite crucible and mold. The atomization was conducted at $1450^{\circ}C$ under the vacuum of $10^{-2}$ torr. The gas pressure during atomization was varied from 35 to 50 bars. After making the Ni amorphous powders, the spray drying was processed to produce the Cu -coated Ni amorphous composite powder. The amorphous powder and Cu nitrate solution were mixed together with a small amount of binder and then it was sprayed at temperature of $130^{\circ}C$ and rotating speed of 15,000 R.P.M.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.597-603
• /
• 2016

Tantalum carbide, which is one of the ultra-high temperature ceramics, was deposited on graphite by low pressure chemical vapor deposition from a $TaCl_5-C_3H_6-Ar-H_2$ mixture. To maintain a constant $TaCl_5/C_3H_6$ ratio during the deposition process, $TaCl_5$ powders were continuously fed into the sublimation chamber using a screw-driven feeder. Sublimation behavior of $TaCl_5$ powder was measured by thermogravimetric analysis. TaC coatings have various phases such as $Ta+{\alpha}-Ta_2C$, ${\alpha}-Ta_2C+TaC_{1-x}$, and $TaC_{1-x}$ depending on the powder feeding methods, the $C_3H_6/TaCl_5$ ratio, and the deposition temperatures. Near-stoichiometric TaC was obtained by optimizing the deposition parameters. Phase compositions were analyzed by XRD, XPS, and Raman analysis.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.905-912
• /
• 2011

In this study, the novel concept catalytic reactor was designed for water-gas shift reaction (WGS) under high pressure. The novel concept catalytic reactor was composed of an autoclave, the catalyst, and liquid water. Cu-ZnO/$Al_2O_3$ as the low temperature shift catalyst was used for WGS reaction. WGS in the novel concept catalytic reactor was carried out at the ranges of 150~$250^{\circ}C$ and 30~50 atm. The liquid water was filled at the bottom of the autoclave catalytic reactor and the catalyst of pellet type was located at the gas-liquid water interface. It was concluded that WGS reaction occurred over the surface of catalysts partially wetted with liquid water. The conversion of CO for WGS was also controlled with changing content of Cu and ZnO used as the catalytic active components. Meanwhile, the catalyst of honey comb type coated with Cu-ZnO/$Al_2O_3$ was used in order to increase the contact area between wet-surface of catalyst and the reactants of gas phase. It was confirmed from these experiments that $H_2$/CO ratio of the simulated coal gas increased from 0.5 to 0.8 by WGS at gas-liquid water interface over the wet surface of honey comb type catalyst at $250^{\circ}C$ and 50 atm.

• 한국통신학회논문지
• /
• 제17권2호
• /
• pp.142-152
• /
• 1992

본 논문에서는 광파이버 센서로써 고전계(고전압)측정의 어려움을 해결하기 위하여 지금까지 알려진 다른 전기광학 소자보다 반파장 전압이 매우 높은 SiO2를 사용하여 고전계을 계측하기 위한 새로운 방법을 제시 하였다. SiO2를 비롯한 광학소자로 구성된 센서내부, 즉 전광자 및 편광자에서의 광변조식을 Stokes Parameter와 Mueller 행렬로 유도 하였고 이를 복굴절 결정에서의 전기광학 효과를 이론적으로 해석하고 위상지연과 반파장 전압을 계산하였다. 설계 제작한 광전압 센서에 , 분압없이 최대전압 20KV까지 공급 했을때의 출력신호를 검출한 결과 오차는 3%미만으로서 매우 우수한 직선성을 얻었다. SiO2의 온도변화(-20~60$^{\circ}$C)에 따른 출력전압 변화를 실험한 결과 최대 7.5%까지 변동율이 발생하였으나 열처리 한후로는 1.0% 이내로 개선된 특성을 보였다.

• 자원리싸이클링
• /
• 제6권1호
• /
• pp.29-34
• /
• 1997

산업 폐기물의 일종인 석회석 슬러지, 폐주물사, 석탄회 및 폐유리병을 고온에서 용융 슬래그화 하여 시멘트 원료로서의 활용 가능성을 검토하고자 하였다. 각 폐기물을 혼합한 후 용융처리하여 얻은 용융 슬래그는 $\beta$-$C_2$S(2CaO.$SiO_2$) 및 $C_2$AS(2CaO.$Al_2$$O_3$.$SiO_2$)의 2가지 상으로 구성되어 있다. 폐기물의 용융처리시 용융온도, 냉각속도 및 염기도 등을 변화시키면서 이들 요인이 $\beta$-$C_2$S상의 생성율에 미치는 영향을 조사하였다. 시멘트 원료로서 활용이 가능한 $\beta$-$C_2$S상의 함율을 높이기 위해서는 첫째 용융온도를 낮추어 용융슬래그의 제조에 필요한 최소한의 온도에서 용융시키고, 둘째 용융물을 고온에서 급냉시키며, 셋째 낮은 염기도를 갖도록 혼합물의 조성을 조절하는 것이 필요하다.

• 한국전산구조공학회논문집
• /
• 제27권4호
• /
• pp.265-271
• /
• 2014

304L 스테인리스강판은 멤브레인타입 LNG선 단열시스템의 1차 방벽으로 이용된다. 304L 스테인리스강은 변태유기소성(TRIP)강으로 복잡한 재료거동을 보이는데, 이는 소성변형이 발생하는 동안 상변태를 경험하기 때문이다. 본 연구에서는 304L 스테인리스 강의 비선형 기계적 거동분석을 위한 온도의존 일축인장시험을 수행하였으며 재료의 파단이나 비선형 거동을 예측하기 위한 점소성모델을 제안하였다. 수치해석의 결과와 시험 결과를 비교 분석하여 유효성을 검증하였으며 LNG 멤브레인에 대한 적용성을 검토하기 멤브레인 구조시편을 제작하여 구조해석 및 유한요소해석을 수행하였다. 재료모델은 개발 서브루틴을 이용하였으며 ABAQUS 사용자지정 재료 서브루틴을 탑재한 유한요소해석 결과와 극저온 구조인장시험을 수행한 결과를 비교하여 구조적용성을 검증하였다.