• 소성∙가공
• /
• 제8권3호
• /
• pp.247-247
• /
• 1999

The segregation (distribution) of nickel and the composition of its constituents influence the low thermal expansion characteristics (Invar effect) in Fe-30 wt.% Ni-12.5 wt.% Co-xC Invar alloy. The change of coefficient of the thermal expansion and magnetic properties were studied as an aspect of carbon addition causing the segregation of Ni in primary austenite of as-cast Fe-30 wt.% Ni-12.5 wt.% Co Invar alloy. The coefficient of thermal expansion of Fe-30 wt.% Ni-12.5 wt.% Co-xC Invar alloy showed its lowest value at 0.08 wt.% carbon, increased with increasing carbon content in the range of 0.08-1.0 wt.%C, kept constant at 1.0-2.0 wt.%C and decreased at carbon higher than 2.0 wt.%. The effective distribution of the coefficient of nickel in as-cast Fe-30 wt.% Ni-12.5 wt.% Co-xC Invar alloy increased with increasing carbon content. The volume fraction of they phase of Fe-30 wt.% Ni-12.5 wt.% Co-xC alloy increased with increasing carbon content. The microstructure of Fe-30 wt.% Ni-12.5 wt.% Co-xC alloy changed with the carbon content was independent of the coefficient of thermal expansion. The Curie temperature changed linearly with the carbon content and was similar to the change of the coefficient of thermal expansion. Moreover, the coefficient of thermal expansion decreased when the ratio of saturation magnetization to Curie temperature ($\sigma_s/T_c$) increased, decreasing the Curie temperature and showed a specific relationship with the magnetic properties of the Fe-30 wt.% Ni-12.5 wt.% Co-xCInvar alloy.

• 한국방사선학회논문지
• /
• 제5권3호
• /
• pp.127-134
• /
• 2011

본 논문에서는 온도와 습도 및 냉 난방을 조절하여 건물 내의 쾌적한 환경을 제공하기 위한 승압쵸퍼와 PWM 전압형 인버터로 구성된 태양광 발전 시스템을 제안하였다. 이 시스템은 안정된 변조를 위해 원칩 마이크로프로세서를 사용하여 동기신호와 제어신호로 처리하였다. PWM 전압형 인버터와 위상의 동기를 위하여 계통전압을 검출하여 계통전압과 인버터 출력을 동상 운전하므로 잉여전력을 연계할 수 있게 하였으며, 건물이나 병원 등 특정 건물의 온도 및 습도센서에 적용하여 양호한 동특성을 얻을 수 있었다. 또한 시스템에 적용한 결과 고역률과 저고조파 출력을 유지함으로써 부하와 계통에 전력이 안정하게 공급될 수 있도록 제어하여 좋은 결과를 얻을 수 있었다.

• 한국의류학회지
• /
• 제5권1호
• /
• pp.15-21
• /
• 1981

The effect of fatty acid content in oily soil and conditions of washing on the removal of triglyceride have been studied. Cotton lawn was soiled with the four-component soil-tripalmitin, palmitic acid, dodecyl alcohol and dodecane-and washed in constant temperature waterbath shaker. The detergency was estimated by analysis of triglyceride labelled carbon-14 on fabrics before and after washing by means of liquid scintillation counting. It was shown that the detergency of triglyceride washed with the nonionic, nonylphenol poly (10)-ethylene oxide and soap was increased steadily with increasing temperature, whereas with the anionics Na-DBS and SLS, the detergency was rather decreased when the temperature was elevated above $40^{\circ}C$. To investigate the effects of free fatty acid content in soil on the removal of triglyceride, the fabrics were soiled altering palmitic acid content, and then washed. From the results, the detergency of triglyceride was developed with increasing free fatty acid content. With soils containing less than $30\%$ of free fatty acid, of the three detergents tested, the nonionic was by far the most effective soil removal. Soap was intermediate and the synthetic anionic was the poorest. With soil containing $45\%$ of free fatty acid, soap was the most effective soil removal. When NaOH was added to detergent solution. the detergency of triglyceride was improved without regard to detergents. The optimum alkalinity was obtained according to free fatty acid content. And the alkalinity changed to low NaOH concentration with increasing free fatty acid content. From the results mentioned above, it could be concluded that the major removal mechanisms of triglyceride containing oily soil were mesomorphic phase formation, solubilization and soap forma-tion when alkali was added in detergent solution.

• 한국세라믹학회지
• /
• 제32권11호
• /
• pp.1292-1300
• /
• 1995

The ionic conductivity of NASICON solid electrolytes was simulated by using Monte Carlo Method (MCM). There were included two conduction paths: (1) Na1-Na2 and (2) Na1-Na2 including Na2-Na2. We assumed that mid-Na ions provde an additional driving force for Na mobile ions due to the interionic repulsion between Na1 and Na2 ions. The inflection point of vacancy availability factor, V has been shown at nearby x=2, the maximum mid-Na ions. The inflection point of vacancy availability factor, V has been shown at nearby x=2, the maximum mid-Na sites are occupied. The effective jump frequency factor, V has been shown at nearby x=2, the maximum mid-Na sites are occupied. The effective jump frequency factor, W increased rapidly with the composition at low temperature, but decreased at high temperature region. On Na1-Na2 conduction path, the minimum of charge correlation factor, fc and the maximum of $\sigma$T were appeared at x=2.0. this indicated that mid-Na ions affect on the high ionic conductivity behavior. At the whole range of NASICON composition, 1n $\sigma$T vs. 1/T* plots have been shown Arrhenius behavior but 1n (VWFc) vs. 1/T* have been shown the Arrhenius type tendency at x=2, which mid-Na is being the maximum. The results of MCM agreed with the experimental one when the chosen saddle point value was 6$\varepsilon$ : 3$\varepsilon$. Here the calculated characteristic parameter of materials, K and the phase transition temperature were -4.001$\times$103 and 178$^{\circ}C$ (1/T*=1.92, 1000/T=2.22), respectively.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2003년도 춘계학술연구발표회
• /
• pp.8-8
• /
• 2003

Electron-phonon interaction plays a significant role in forming of colossal magnetoresistance effect (CMR). Polaron formation was observed by neutron diffraction and by extended X-ray absorption fine structure (EXAFS) analysis. Local probe as given by the EXAFS is a useful method to study the polaronic charge and its dependence on temperature and ions size. Here we present the EXAFS study of polaronic charge in La/sub 0.7/Ca/sub 0.3-X/Ba/sub X/MnO₃ compositions. The single phase La/sub 0.7/Ca/sub 0.3-X/Ba/sub X/MnO₃ manganites (x=0; 0.03; 0.06, ..., 0.3) were prepared by ceramic technology [1]. The Curie temperature was determined by extrapolation of the temperature dependence of the magnetization (down to zero magnetization). EXAFS experiments were carried out at the 7C EC beam line of the Pohang Light Source (PLS) in Korea. The atomic pair distribution functions (PDF) were obtained by re-regularization method [2] from filtered spectra. The PDF for the x=0.3 sample showed a single peak function and for x=0.0, 0.03, 0.06, 0.09, 0.12 compositions were asymmetric in agreement with a small Jahn-Teller elongation of two (short and long) bonds of the MnO/sub 6/ octahedron. Dispersion, σ/sub Min-O//sup 2/, and asymmetry, σ/sub Min-O//sup 3/, of the Mn-O bond distances varied significantly with x and showed a maximums at x=0.09. The maximum of σ/sub Min-O//sup 2/ is caused by increase of dynamic rms displacements of the Mn-O distances near the T/sub C/. The observed x dependence of σ/sub Min-O//sup 3/ reflects the reduction of charge carriers mobility at approaching to T/sub C/ from low as well as high temperatures.

• 한국재료학회지
• /
• 제23권2호
• /
• pp.98-103
• /
• 2013

$Mg_{3-x}Zn_xSb_2$ powders with x = 0-1.2 were fabricated by mechanical alloying in a planetary ball mill with a speed of 350 rpm for 24 hrs and then hot pressed under a pressure of 70 MPa at 773 K for 2 hrs. It was found that there were systematic shifts in the X-ray diffraction peaks of $Mg_3Sb_2$ (x = 0) toward a higher angle with increasing Zn for both the powder and the bulk sample and finally the phase of $Mg_{1.86}Zn_{1.14}Sb_2$ was formed at the Zn content of x = 1.2. The $Mg_{3-x}Zn_xSb_2$ compounds had nano-sized grains of 21-30 nm for the powder and 28-66 nm for the hot pressed specimens. The electrical conductivity of hot pressed $Mg_{3-x}Zn_xSb_2$ increased with increasing Zn content and temperature from 33 $Sm^{-1}$ for x = 0 to 13,026 $Sm^{-1}$ for x = 1.2 at 323 K. The samples for all the compositions from x = 0 to x = 1.2 had positive Seebeck coefficients, which decreased with increasing Zn content and temperature, which resulted from the increased charge carrier concentration. Most of the samples had relatively low thermal conductivities comparable to the high performance thermoelectric materials. The dimensionless figure of merit of $Mg_{3-x}Zn_xSb_2$ was directly proportional to the Zn content except for the compound with Zn = 1.2 at high temperature. The $Mg_{3-x}Zn_xSb_2$ compound with Zn = 0.8 had the largest value of ZT, 0.33 at 723 K.

• Journal of Magnetics
• /
• 제4권1호
• /
• pp.33-37
• /
• 1999

Unidirectional magnetic anisotropy field ($H_an$) was investigated for thin films of $CdCr{2-2x}In_{2X}Se_4 (0$\leq$x$\leq$0.2). This anisotropy originates from the microscopic anisotropic Dzyaloshinskii-Moriya (DM) interaction which arise from the spin-orbit scattering of the conduction electrons by the nonmagnetic impurities. This interaction maintains the remanent magnetization in the direction of the initial applied field. Then the single easy direction of the magnetization is parallel to the direction of the magnetic field. The anisotropy produced by field cooling is unidirectional I.e. the spins system deeps some memory of the cooling field direction. The chalcogenide spinel of$ CdCr_{2-2x}In){2X}Se_4$belongs to the class of the magnetic semiconductors. The magnetic disordered state is obtained when ferromagnetic structure is diluted by In. Then we have the mixed phase characterised by coexistence the magnetic long range ordering (IFN-infinite ferromagnetic network) and the spin glass order (Fc-finite clusters). The total magnetic anisotropy energy depends on the state of magnetic ordering. In our study we concentrated on the magnetic state with reentrant transition and spin glass state. The polycrystalline $ CdCr_{2-2x}In){2X}Se_4$ thin films were obtained by rf sputtering technique. We applied the ferromagnetic resonance (FMR) and M-H loop techniques for determining the temperature composition dependencies of Han. From the experimental data, we have found that Han decreases almost linearly when temperature is increased and in the low temperature is about three times bigger at SG state with comparison to the state with REE.

• 대기
• /
• 제26권1호
• /
• pp.203-214
• /
• 2016

This study explores the 6-month lead prediction skill of stratospheric temperature and circulations in the Global Seasonal forecasting model version 5 (GloSea5) hindcast experiment over the period of 1996~2009. Both the tropical and extratropical circulations are considered by analyzing the Quasi-Biennial Oscillation (QBO) and Northern Hemisphere Polar Vortex (NHPV). Their prediction skills are quantitatively evaluated by computing the Anomaly Correlation Coefficient (ACC) and Mean Squared Skill Score (MSSS), and compared with those of El Nino-Southern Oscillation (ENSO) and Arctic Oscillation (AO). Stratospheric temperature is generally better predicted than tropospheric temperature. Such improved prediction skill, however, rapidly disappears in a month, and a reliable prediction skill is observed only in the tropics, indicating a higher prediction skill in the tropics than in the extratropics. Consistent with this finding, QBO is well predicted more than 6 months in advance. Its prediction skill is significant in all seasons although a relatively low prediction skill appears in the spring when QBO phase transition often takes place. This seasonality is qualitatively similar to the spring barrier of ENSO prediction skill. In contrast, NHPV exhibits no prediction skill beyond one month as in AO prediction skill. In terms of MSSS, both QBO and NHPV are better predicted than their counterparts in the troposphere, i.e., ENSO and AO, indicating that the GloSea5 has a higher prediction skill in the stratosphere than in the troposphere.

• 한국식품과학회지
• /
• 제33권1호
• /
• pp.7-11
• /
• 2001

정제된 Aigeok Polysaccharide의 분자량은 $5.5{\times}10^4$ Da였고, 분자량 분포는 단분산도에 가까웠으며, FT-IR 스펙트럼으로부터 메칠에스테르화된 정도는 낮은 것으로 확인되었다. Aigeok polysaccharide의 겔화 속도는 칼슘이온과 온도에 크게 영향을 받으며 4.08mM 칼슘 이온이 첨가될 때까지는 탄성률의 세기가 증가하였다가 그 이상이 되면 저장탄성률과 손실탄성률 모두 감소하였다. Aigeok polysaccharide의 화학적 구조와 junction zone은 적절한 양의 칼슘이온에 의해 안정화됨을 알 수 있었고 과량의 칼슘농도하에서는 그물구조 형성이 방해를 받아 탄성률은 감소하였다. 겔화 속도 상수는 온도가 증가함에 따라 감소하였고 이는 Aigeok 분자간에 수소결합이 주된 역할을 한다는 것을 알 수 있었다. Aigeok polysaccharide의 겔화 능력은 4.08mM의 칼슘 첨가와 $5^{\circ}C$에서 가장 안정한 겔을 형성함을 알 수 있었고, 반응식이 겔화를 추정하는데 좋은 표준이 됨을 알 수 있었다.

• 한국자기학회지
• /
• 제2권2호
• /
• pp.91-98
• /
• 1992

$Co_{67}Fe_{4.5}Nb_{2}Si_{10}B_{15}$ 비정질합금리본에서 2단 어닐링이 자기특성에 미치는 영향을 조사 하였다. 고온인 $480^{\circ}C$ 이상에서 20분간 1단 어닐링한 리본을 저온인 $310^{\circ}C$에서 2시간 동안 2단으로 진공어닐링한 결과 보자력과 각형비는 1단 어닐링한 경우와 거의 비슷한 값들을 나타내었으나, 직류 및 교류투자율은 1단 어닐링에 비해 현저히 높아졌다. 2단 어닐링시 직류 및 1 kHz에서의 교류투자율의 최대치는 각각 약 290,000과 41,000으로서 1단 어닐링에 비해 30% 이상 증가하였다. 어닐링온도에 따른 자성의 변화는 3단계로 나누어 내부응력, 자구크기, cluster 및 결정상의 변화를 주요 요인으로 하여 고찰하였다.