• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.101-103
• /
• 2007

Since they use the low switching frequency in multilevel inverter systems, they generate the high low frequency harmonic components. Generally, LC filter is used at the output terminal of inverter systems to solve this problem. But it causes a voltage drop at the output terminal by use of damping resistors, and causes the problem in which system efficiency decreases due to power loss of the damping resistor. In this paper, we proposed an output filter design method for NPC three-level inverter systems with low switching frequency. And we analyzed the efficiency of the proposed filter system, and the effectiveness of the proposed system is verified by simulation and experimental results.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.823-834
• /
• 2009

This paper proposes a high-efficiency single-stage ac/dc converter. The proposed converter features low voltage stresses and reduced switching losses. It operates at the boundary of discontinuous- and continuous-conduction modes by employing variable switching frequency control. The turn-on switching loss of the switch can be reduced by turning it on when the voltage across it is at a minimum. The voltage across the bulk capacitor is independent of the output loads and maintained within the practical range for the universal line input, so the problem of high voltage stress across the bulk capacitor is alleviated. Moreover, the voltage stress of the output diodes is clamped to the output voltage, and the output diodes are turned off at zero-current. Thus, the reverse-recovery related losses of the output diodes are eliminated. The operational principles and circuit analysis are presented. A prototype circuit was built and tested for a 150 W (50V/3A) output power. The experimental results verify the performance of the proposed converter.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1306-1315
• /
• 2016

Modern power systems driven by high-power converters have become inevitable in view of the ever increasing demand for electric power. The total power loss can be reduced by limiting the switching losses in such power converters; increased power efficiency can thus be achieved. A reduced switching frequency that is less than a few hundreds of hertz is applied to power converters that produce output waveforms with high distortion. Selective harmonic elimination pulse width modulation (SHEPWM) is an optimized low switching frequency pulse width modulation method that is based on offline estimation. This method can pre-program the harmonic profile of the output waveform over a range of modulation indices to eliminate low-order harmonics. In this paper, a SHEPWM scheme for three-phase three-leg neutral point clamped inverter is proposed. Aside from eliminating the selected harmonics, the DC capacitor voltages at the DC bus are also balanced because of the symmetrical pulse pattern over a quarter cycle of the period. The technique utilized in the estimation of switching angles involves the firefly algorithm (FA). Compared with other techniques, FA is more robust and entails less computation time. Simulation in the MATLAB/SIMULINK environment and experimental verification in the very large scale integration platform with Spartan 6A DSP are performed to prove the validity of the proposed technique.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.166-176
• /
• 2007

Radio frequency (RF) microelectromechanical systems (MEMS) have been pursued for more than a decade as a solution of high-performance on-chip fixed, tunable and reconfigurable circuits. This paper reviews our research work on RF MEMS switches and switching circuits in the past five years. The research work first concentrates on the development of lateral DC-contact switches and capacitive shunt switches. Low insertion loss, high isolation and wide frequency band have been achieved for the two types of switches; then the switches have been integrated with transmission lines to achieve different switching circuits, such as single-pole-multi-throw (SPMT) switching circuits, tunable band-pass filter, tunable band-stop filter and reconfigurable filter circuits. Substrate transfer process and surface planarization process are used to fabricate the above mentioned devices and circuits. The advantages of these two fabrication processes provide great flexibility in developing different types of RF MEMS switches and circuits. The ultimate target is to produce more powerful and sophisticated wireless appliances operating in handsets, base stations, and satellites with low power consumption and cost.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.38-39
• /
• 2017

This paper proposes a new control method for an AC-DC Buck converter which is utilized as a front-end converter of a 2-stage high power density adapter. In the conventional adapter applications, 2-stage configuration shows higher power transfer efficiency and higher power density than those of the single stage flyback converter. In the 2-stage AC-DC converter, the boost converter is widely used as a front-end converter. However, an efficiency variation between high AC line and low AC line is large. On the other hand, the proposed conduction band control method for a buck front-end converter has an advantage of small efficiency variation. In the proposed control method, switching operation is determined by a band control voltage which represents output load condition, and an AC line voltage. If the output load increasesin low AC line, the switching operation range is expanded in half of line cycle. On the contrary, in light load and high line condition, the switching operation is narrowed. Thus, the proposed control method reduces switching loss under high AC line and light load condition. A 60W prototype which is configured the buck and LLC converter with the proposed control method is experimented on to verify the validity of the proposed system. The prototype shows 92.16% of AC-DC overall efficiency and 20.19 W/in 3 of power density.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1018-1019
• /
• 2015

Recently, standby power reduction techniques of AC/DC adaptor were developed, consuming power almost arrived to 300mW level. The standby power losses are composed of the input filter loss 11.8mW, the control IC for AC/DC adaptor 18mW, the switching loss 9.53mW and the feedback loss 123mW. And there are the standby power reduction techniques. In this paper, in order to reduce the standby power of SMPS more, the loss due to a voltage difference between input and output is reduced by the control circuit which is composed of the low voltage driving circuit and voltage regulator. The low voltage driving circuit operates on the low voltage of input and off the high voltage. The low voltage driving IC was produced by the $1.0{\mu}m$, high voltage DMOS process.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.140-142
• /
• 2005

SMPS의 손실에는 switching loss, conduction loss, core loss가 있다. 최근 SMPS에서는 switching loss를 줄여 효율을 높이고자 반도체 스위치 2개를 사용하는 공진형 구조가 증가하고 있다하지만 공진형 구조는 반도체 스위치에서 소비되는 conduction loss로 의해 기존의 컨버터에 비해 무부하시 전력 소모가 크다. 그러나 최근 시장은 무부하시 소비되는 대기전력의 규제가 이슈가 되고 있다. 본 논문에서는 active clamped flyback converter에서 무부하시 반도체 스위치의 conduction loss의 감소를 위해 Clamp 회로의 보조 스위치는 동작시키지 않고, flyback converter로만 동작하도록 설계하여 무부하시에는 기존의 flyback converter의 동작과 같이 도통 손실이 급속히 줄도록 하였다. 또한 스위칭 손실을 줄이기 위해 주 스위치의 동작 주파수를 감소시켜 SMPS의 무부하시의 소모를 감소시켰다. 70W급 SMPS의 제작과 실험을 통해 위의 방법을 증명하고자 한다.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.126-128
• /
• 2007

This paper presents a new soft switching dc-to-dc converter that employs IM transformer. Detailed analysis and design considerations of the proposed circuits are presented. By applying the proposed magnetic integration procedure, new integrated magnetic circuits featuring low loss, simple structure are then developed to overcome the limitations of prior art. Consequently, the power loss and the size of the integrated magnetic device are greatly reduced. The operation and performance of the proposed converter are demonstrated with an experimental converter that delivers a 5V/5A output from a 48V input at the maximum efficiency of 90 %.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.266-268
• /
• 2005

A new synchronous switch controlled transient current build-up zero voltage switching (TCB-ZVS) forward converter is proposed. The proposed converter is suitable for the low-voltage and high-current applications. The features of the proposed converter are low conduction loss of magnetizing current, no additional circuit for the ZVS operation, high efficiency, high power density and low EMI noise throughout all load conditions.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.413-416
• /
• 1997

In this paper, we propose a new single-stage isolated switching power supply. The proposed converter reduces the diode conduction loss and offer both the high input Power factor and the direction conversion from the ac line to a dc output voltage. This paper present the Operational principle, analysis and control and experimental results of a 100W prototype.