• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.631-640
• /
• 2016

A dual-mode power management for a hybrid-electric UAV with a cruise power of 200W is proposed and empirically verified. The subject vehicle is a low-speed long-endurance UAV powered by a solar cell, a fuel cell, and a battery pack, which operate in the same voltage bounds. These power sources of different operational characteristics can be managed in two different methods: passive management and active management. This study proposes a new power management system named PMS2, which employs a bypass circuit to control the individual power sources. The PMS2 normally operates in active mode, and the bypass circuit converts the system into passive mode when necessary. The output characteristics of the hybrid system with the PMS2 are investigated under simulated failures in the power sources and the conversion of the power management methods. The investigation also provides quantitative comparisons of efficiencies of the system under the two distinct power management modes. In the case of the solar cell, the efficiency difference between the active and the passive management is shown to be 0.34% when the SOC of the battery is between 25-65%. However, if the SOC is out of this given range, i.e. when the SOC is at 90%, using active management displays an improved efficiency of 6.9%. In the case of the fuel cell, the efficiency of 55% is shown for both active and passive managements, indicating negligible differences.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3821-3826
• /
• 2014

This paper proposes a methodology for developing the performance of a solenoid valve for vehicles based on the dynamic analysis model by an electromagnetic field. The high performance solenoid model with a low current and high thrust was induced through the shape optimal design of the yoke and plunger. To perform the dynamic analysis of the solenoid valve, the input current profile was analyzed. The speed and thrust information was analyzed by FEM with this current profile. The co-simulation method of the circuit model of control logic and electromagnetic model of the solenoid valve was also proposed to analyze the performance with several current patterns. Finally, the performance of the original model and optimal one was compared.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.12
• /
• pp.6106-6113
• /
• 2013

Automotive three-way catalyst substrate has a cordierite ceramic honeycomb structure. The substrate in the high engine speed range doesn't satisfy the design fatigue life due to the low mechanical properties of cordierite ceramic. SiC ceramic has higher mechanical properties than cordierite ceramic. If the automotive three-way catalyst substrate is made from the SiC ceramic honeycomb structure, the substrate can be prevented from premature failure. In this study, the mechanical properties of SiC ceramic honeycomb substrate were estimated by FEA. The FEA results indicated that the MOR and elastic modulus for the SiC ceramic honeycomb substrate was much higher than those for the cordierite ceramic honeycomb substrate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.104-117
• /
• 1999

The Composite materials has been used in the field of high technology industry because of high specific stiffness and high specific strength. Specially, the composite materials has been widely applied to the field of the aircraft and the transportation by the effectiveness of light weight due to low specific weight and reduction of the parts due to bonding, molding and so on. These advantages about the composite have led to study and apply in the transmission shaft for the aircraft and the drive shaft for the automobile. The composite material propeller shaft with the high vibrational stability was designed and analyzed. In order to verify the analysis, two types of experimental test which are the FFT analyzer with impact hammer and the rotational equipment were applied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.95-101
• /
• 2012

An electric water pump for engine cooling system has an advantage which particularly in the cold start, the use of the electric water pump saves fuel and leads to a corresponding reduction in emissions. The canned type electric water pump without mechanical sealing elements was selected to meet the requirements for operational reliability and life. However, the electric water pump for internal combustion engine generates much more heat loss than for hybrid electric vehicle since it is operated by the electric power of high current and low voltage. In this study, the fluid flow and thermal characteristics of the canned type electric water pump as an inverter integrated water pump has been investigated under the effects of heat generation. The analysis conditions such as outdoor air temperature of $125^{\circ}C$, water pump speed of 6000 rpm, coolant temperature of $106^{\circ}C$ and coolant flow rate of 120 L/min was used as a standard condition. Therefore, flow fields and temperature distribution inside the water pump were obtained. Also, we checked the feasibility of the canned type for the electric water pump in comparison with the mechanical seal type.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.129-134
• /
• 2010

A diesel engine is equipped with a turbocharger for providing more power at a low engine speed region by supplying charge air to combustion chambers. The turbocharger makes it possible to satisfy stringent emission regulations and customers' demand of enjoying the fun to drive by increasing engine performance. However, the turbocharger has the disadvantage of making BPF(Blade Passing Frequency), hissing, surge, whistle, and blow noises. Among them, reducing the blow noise, a narrow-band noise(a general range : 1800~2000Hz), is possible by using a resonator that controls the narrow frequency band governing the resonance in the intake system. In this study, the optimum location of the resonator is found by employing Boost as a CAE(Computer Aided Engineering) tool and is confirmed by experiments of an engine dynamo test and a real vehicle test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.125-132
• /
• 2002

Bumpers are structural components to reduce physical damage to the front and rear ends of a passenger motor vehicle from low speed collisions. Damage assessment and the protectiveness are the commonly used designing criteria but in this study, relative displacements of the bumper are examined. To absorb the crash energy without significant damage to the bumper itself, foam material is installed between fascia and beam. However, it is not easy to predict the exact displacements generated in bumper structures through FEM because the compressive stress-strain curve of a foam material depends on strain rates that deviates significantly on each trial. Under this uncertain condition, a range of displacements is calculated and the optimum design is performed using the design of experiments. The result will be used to find the design that minimizes the weight within displacement constraints. The orthogonal array of L9 is introduced to find the optimum of the design variables that considers the thickness of inner beam, outer beam and stay, This study will suggest the design procedure of a front bumper using the uncertain stress-strain curve of a foam material.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.146-156
• /
• 1995

Growing international concern about environmental issues in recent years has led to new proposals for strengthening exhaust emission standards and fuel economy requirements throughout the world. The low emission vehicle(LEV) standards drawn up by the California Air Resources Board(CARB) in the U.S.A are noticeably stringent To cope with this regulation, a reduction of HC emission is the most important challenge for the automotive industry because HC emission levels are severer than any other components emission levels. In this paper, the apparatus for visulalizing the wall film flow in a intake manifold and the spark plug with optical fiber for detecting the signal from diffusion flame are developed to mal,e the HC formation mechanism clear. High speed camera system is also used to elucidate the correlation wall film flow and the diffusion flame. Using these methods, the effect of fuel injection systems such as injection direction, spray angle, atomised injection on HC emission levels is investigated. Consequently, the optimal fuel injection conditions for minimizing the wall film flow and reducing the HC emission are found through this research.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.612-618
• /
• 2009

Recently the roles of railways about the prevention of global warming caused by greenhouse gases and for low carbon green growth are larger than ever. And the railroad-related research institutions have been active in researching for energy conservation. Especially the urban railroad has been emerged as the best means of transportation compared to the general public transportation systems in punctuality, stability, ecology and etc. In operating the urban railroad system there are various ways for energy savings. In the larger category, One is the hardware aspect according to the structure of the vehicle and the development of control systems. The other is the software aspect which efficient train operation can be made through control of driving patterns and driving diagram. In this paper, there is sense to analyze the result in verifying expectation relation with variable and the use of electric power on this after selecting main variables that can influence to the energy of the train operation in the software aspect. First, after collecting the basic data related to operation(train speed, operating hours, power consumption, the position of stopping station, electrical power system etc.) and according to this, investigating the consumption of the energy of the operation, in the side of energy consumption deducing and analyzing problem, this will be found solutions.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.4
• /
• pp.432-440
• /
• 2015

UGVs(Unmanned Ground Vehicles) are robots that can substitute humans in reconnaissance operations of potentially dangerous and contaminated sites. Currently, there have been active research on utilizing UGVs in military environments. Much resrach has been focused on exploiting the weakness of topology-based routing and instead utilize location-based routing for the networking of UGVs. It is generally assumed that location-based routing methods can fully utilize the location information gained from GPS. However, this may not be possible in tactical environments due to enemy GPS jamming and LOS(Line of Sight) limitations. To solve this problem, we propose a location-based routing scheme utilizing low control message that can calibrate the location information using GPS information as well as location of neighboring UGV, movement direct and speed information. Also utilizing topology-based routing scheme to solve incorrect location information in GPS jamming region.