• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.465-468
• /
• 2004

In this paper, we describe the design and implementation of the new current-current negative feedback (CCNF) voltage-controlled oscillator (VCO), which suppresses 1/f induced low-frequency noise. By means of the CCNF, the high-frequency noise as well as the low-frequency noise is prevented from being converted into phase noise. The proposed CCNF VCO shows 11-dB reduction in phase noise at 10 kHz offset, compared with the conventional differential VCO. The phase noise of the proposed VCO is -87 dBc/Hz at 10 kHz offset frequency from 5.5-GHz carrier. The proposed VCO consumes 14.0 mA at 2.0 V supply voltage, and shows single-ended output power of -12.0 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.94-99
• /
• 1997

There are several factors that have influence on the phase noise of an oscillator. But one of the major factors is the flicker noise of a transistor, since the phase noise of an oscillator is generated by mixing the carrier with the low frequency noise near the DC having the characteristic of 1/f. In this paper, we have presented a method on reducing the phase noise of an oscillator by using a low-frequency feedback circuit based on an active bias circuit, and have fabricated a DRO for a DBS receiver. Measurement results show that the phase noise is -92 dBc/Hz at the 10 KHz offset frequency, and from these results we have found out that the reduction method is very effective.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.748-753
• /
• 2002

In this paper, a new topology of a active capacitor is proposed in order to apply the resonator in the design of RF active bandpass filters. Through the noise analysis of the active capacitor, the optimized low noise design process is also presented, Due to the low noise performance of the proposed active bandpass filter, it can be used in the RF front-end of the receivers. In designed 2-stage active bandpass filter at 1.9 GHz shows insertion loss of 0 dB, noise figure of 2.6 dB, and OIP3 of 8 dBm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.857-861
• /
• 2004

An active method that improves low frequency characteristics of a reverberation chamber has been proposed. Spatial uniformity of sound pressure at low frequency has been increased by applying active noise control system. The system acts as frequency selective damping materials, which decreases resonance at low frequency and leave high frequency sound field as it is. Linearity of the chamber, which is essential for sound power measurement in the chamber, is guaranteed since fixed control logic has been adopted. Simple application and tests have been done in a small sized rectangular reverberation chamber which has 400Hz cutoff, Loud speakers were used to simulate a noise source and to construct an active noise control system. The spatial distribution of a sound field at 250Hz, 315Hz and 400Hz bands has been measured before and after control. The standard deviation of sound field has been decreased from 3.4dB to 2.5dB. The results show the possibility of active control system as a sound diffuser.

• Korean Journal of Human Ecology
• /
• v.1 no.2
• /
• pp.61-74
• /
• 1998

The purpose of this study is to investigate residents subjective opinion of the noise on the low-rise multifamily house in U.S.A. The results of this study can be applied for the prevention of noise when planning cities, roads, and multifamily houses in Korea. The subjects of this study are three kinds of multifamily houses and their 109 residents in Athens, U.S.A. The results of this study are as follows. The residents felt the noise from lawn mowers and the sound from filter fans of air conditioners were higher than in the other external noise. The residents daily activities were disturbed a little by the external noise. Of the internal noise, the air home sound was recognized a little by residents. They only felt a moderate sound level from the building services of the solid borne sound. They suffered worse from noise in the summer and they felt worse from 16∼20 o'clock due to noise. The residents who were living in town houses felt better than those in the other multifamily houses. (Korean J Human Ecology 1(2):61∼74. 1998)

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.898-904
• /
• 2017

DFT(Discrete Fourier Transform) is one of the most widely used method to estimate the phasor of a relaying signal. The harmonics are eliminated by the DFT. However, high frequency components, except for harmonics, are not removed and cause an error in DFT-based phasor estimation process. This paper suggests high frequency noise reduction method by using a newly designed low-pass filter to estimate a signal phasor. When selecting a stop-band cut-off frequency of the low-pass filter, high frequency components generated by faults are considered. To reduce the phasor estimation delay caused by a low-pass filter, this paper proposes a low-pass filter whose settling time is reduced. An adverse effect of high frequency noise on DFT-based phasor estimation is reduced. To evaluate the performance of the proposed method, signals which are collected under a fault condition at a 345[kV] transmission system modeled by EMTP-RV are used.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.608-609
• /
• 2008

An alternator which converts mechanical rotating energy into electric energy is an important component of a vehicle. It operates in broad range from 3000 RPM to 18000 RPM. So, sufficient flow rate and low noise are needed in such broad operating range for a cooling fan of this alternator. In current study, the cooling fan of an alternator is developed through DFSS process and numerical analysis. In order to calculate flow rate and noise level, SC/Tetra and FlowNoise S/W are used respectively, for a new developed fan, compared with original model, numerical result shows 3 dBA reduction and measured value shows 4 dBA reduction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.847-847
• /
• 2004

Automobile cooling fans are operated with a radiator module. To design low noise, high performance cooling fan, radiator resistance should be considered in the design process. The system (radiator) resistance reduces axial velocity and increases effective angle of attack. This increasing effective angle of attack mechanism causes blade stall, performance decrease and noise increase. In this paper, To analyze fan performance, freewake and 3D CFD calculations are used To design high performance fan with consideration of system resistance, optimal twist concept is applied through momentum and blade element theory. To predict fan noise, empirical formula and acoustic analogy methods are used.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.699-700
• /
• 2014

고속도로에 아스팔트 저소음포장이 시공된 현장의 소음조사를 통하여 저소음 아스팔트 포장의 소음저감효과를 분석하였다. 교통량 및 시공시기에 차이가 있는 세 현장에 대하여 측정 시기를 달리하여 저소음포장의 사용 기간에 따른 소음저감효과의 변화를 분석하였으며, 공동주택의 소음대책을 위해 시공된 현장에서는 세대내에서 실질적인 저감효과에 대해 분석하였다. 이 결과를 토대로 저소음포장을 도로소음 대책수단으로 적용을 검토할 경우 설계자가 고려해야할 사항을 제시하고자 하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1011-1014
• /
• 2006

Turbo blower generates high peaks when it operates at high pressure region. The fan of the air-cleaner system, operates especially high pressure region due to several filters, generates high noise level. In this case, the tonal sound of BPF makes people annoyance. The blower of air-cleaner has several high resistance filters in its inlet area and rotates above 900rpm Moreover, for the compact design, the size of the blower should be reduced 10%. The reduced diameter of blower makes low flow rate and high noise level. In order to reduce the noise, new blade shape was suggested and optimized