• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.191-194
• /
• 1998

In this paper, the physical and conductivity properties due to the electron beam irradiation for low density polyethylene using insulating materials of the distribution cable and ultra-high voltage cable are studied. The specimens of the low density polyethylene of thickness 100[$\mu\textrm{m}$] irradiated as each 1 [Mrad], 2[Mrad], 4[Mrad], 8[Mrad], 16[Mrad] and virgin are used in this experiment. In order to measure the conductivity properties, the micro electrometer is used, the range of temperature and app1ying voltage are 20 to 120[$^{\circ}C$], from 100 to 1000[V] respectively So. as a result of the conductivity properties, it is confirmed that the conductivity is increased nearly to 50[$^{\circ}C$], and is not changed until the crystalline melting point from the temperature over 60[$^{\circ}C$] because of the defects of morphology and the formation of many trap centers by means of electron beam irradiation

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.3
• /
• pp.74-85
• /
• 2003

NENA(nitratoethyl nitramine) compounds, especially BuNENA(N-butyl-N-(2-nitratoethyl)-nitramine), are of high interest to both rocket propulsion and military high explosives because of low sensitivity to many forms of stimuli, although they are less energetic than conventional nitrate ester plasticizers. One of advantages in using NENAs is that they provide higher impulse at any given flame temperature than conventional propellants do. BuNENA has better thermochemical characteristics(low melting point and low glass transition temperature), therefore has less tendency to crystallize out of matrices. BuNENA was successfully synthesized in a high yield by reaction of n-butyl aminoethanol and 98% nitric acid followed by dehydrogenation of salt mixture by $Ac_2$/$ZnCl_2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.8
• /
• pp.1546-1552
• /
• 2016

In addition, because it uses preheating to dissolve an alloy in general, it is hard to regulate the appropriate melting temperature of the alloy and brewing time and shows the defect of the supplementation thing due to the super-heating. Once the alloy is molten and then most of the casting by attaching a sight glass or non-contact temperature sensor is suitable casting temperature the operator pressing a button to generate a centrifugal force to inject the molten alloy into a crucible in the casting ring. These results, and most of the cast temperature is too high or too low to generate a lot of casting defects do not get into a uniform cast body. In this paper, we developed a dental casting machine for high frequency using a single temperature sensor which can measure the actual temperature of the alloy than the temperature of the external non-contact measurement using a temperature sensor.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.812-820
• /
• 2002

The positive temperature coefficient (PTC) characteristics of polymer composites were investigated with the nano-sized carbon black particles using solution tasting and melt compounding methods. The polymeric PTC composites should the electrical threshold at 35 wt% for the melt compounding method and 40 wt% for the solution casting method. The ethylene vinylacetate copolymer (EVA) composite showed a gradual increase of resistance as a function of temperature and showed a maximum at the polymer molting point. The resistance of the high-density polythylene (HDPE) composite remains unchanged with temperature but started to Increase sharply near the melting point of HDPE and showed a maximum resistance at the melting point of HDPE. The dispersion of nano-sized carbon black particles was investigated by scanning electron microscopy (SEM) and low resistance after electrical threshold, and both methods exhibited a well dispersed morphology. When the electric current was applied to the PTC composites, the resistance started increasing at the curie temperature and further increased until the trip temperature was roached. Then the resistance remained stable over the trip temperature. The secondary increase started at T$\sub$m/ of matrix polymer and kept increasing up to the trip temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.545-545
• /
• 2007

Recently, innovative process has been investigated in order to replace the conventional high-cost micro patterning processes on the electronic products. To produce desirable profit margins from this low cost products, printed circuit board(PCB), will require dramatic changes in the current manufacturing philosophies and processes. Innovative process using metal nano particles replaces the current industry standard of subtractive etched of copper as a highly efficient way to produce robust circuitry on low cost substrates. An advantage of using metal nano particles process in patterned conductive line manufacturing is that the process is additive. Material is only deposited in desired locations, thereby reducing the amount of chemical and material waste. Simply, it just draws on the substrate as glass epoxy or polyimide with metal nano particles. Particles, when their size becomes nano-meter scale, show some specific characteristics such as enhanced reactivity of surface atoms, decrease in melting point, high electric conductivity compared with the bulk. Melting temperature of metal gets low, the metal nano particles could be formated onto polymer substrates and sintered under $300^{\circ}C$, which would be applied in PCB. It can be getting the metal line of excellent electric conductivity.

• Applied Microscopy
• /
• v.47 no.3
• /
• pp.121-125
• /
• 2017

This study deals the prediction of temperature effect on low-frequency dispersion of alternating current (AC) conductivity spectra of composite materials based on copolymer reinforced with carbon black (CB) particles. A sample of ethylene butylacrylate loaded with 13% of CB particles were prepared and investigated using the impedance spectroscopy representation in the frequency range from 40 Hz to 0.1 MHz and temperature range from $20^{\circ}C$ to $125^{\circ}C$. The dielectric constant, ${\varepsilon}^{\prime}$, and dielectric losses, ${\varepsilon}^{{\prime}{\prime}}$, were found to decrease with increasing frequency. The frequency dependence of the AC conductivity follows the universal power law with a large deviation in the high frequency region, the positive temperature coefficient in resistivity effect has been observed below the melting temperature which makes this composite potentially remarkable for industrial applications.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.3
• /
• pp.25-30
• /
• 2015

SAC-coated Cu specimens were fabricated by novel pad finish process using a phenomenon that metal nanoparticles less than 20 nm in diameter melted at a temperature lower than the melting point of bulk metal, and their wettabilities were evaluated. The thickness of SAC305 layer coated at low temperature of $160^{\circ}C$ using SAC305 ink was extremely thin as the level of several nanometers. It was analyzed by Auger electron spectroscopy that $Cu_6Sn_5$ intermetallic layer with a thickness of 10~100 nm and $Cu_3Sn$ intermetallic layer with a thickness of 50~150 nm were sequentially formed under the SAC305 coating layer. The thickness of formed intermetallic layers was thicker in electroplated Cu than rolled Cu, which attributed to improved surface roughness in the electroplated Cu. The improved surface roughness induces the contact, melting, and reaction of a larger number of SAC305 nanoparticles per the unit area of Cu specimen. In the wetting angle test using SAC305 solder balls, the Cu coated with SAC305 through the low temperature process presented evidently low wetting angles than those in non-coated Cu, indicating that only a few nanometer-thick SAC305 coating layer on Cu could also cause the enhancement of wettability.

• Coupled systems mechanics
• /
• v.7 no.5
• /
• pp.627-634
• /
• 2018

Laser beam welding is more advantageous compared to conventional methods. Titanium/Aluminium dissimilar alloy thin sheet metals are difficult to weld due to large difference in melting point. The performance of the weldment depends upon interlayer formation and distribution of intermetallics. During welding, aluminium gets lost at the temperature below the melting point of titanium. Therefore, it is needed to improve a new metal joining techniques between these two alloys. The present work is carried for welding TI6AL4V and AA2024 alloy by using Nd:YAG Pulsed laser welding unit. The performance of the butt welded interlayer structures are discussed in detail using hardness test and SEM. Test results reveal that interlayer fracture is caused near aluminium side due to low strength at the weld joint.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.379-383
• /
• 2001

Resistance spot welding has been widely used in the sheet metal joining processes because of low cost, high productivity and convenience. Recently, automobile and aerospace industries are trying to replace partly steel sheets with aluminum alloy sheets. But in the case of dissimilar materials, to apply resistance spot welding has been known to be very difficult owing to the effect of melting temperature. On this study, an effort was made to apply spot welding of dissimilar sheet metals, 2024 aluminum alloy and zinc coated steel sheet, evaluate the spot weld quality with tensile-shear strength test and nondestructive evaluation technique, C-scan image methodology. In this study results, as the current below 11 kA, melting of materials is not achieved well. Also as the current exceeds to 13.5 kA, the more spatters happen at welded zone and tensile-shear strength lowered. So, the feasibility of C-scan image technique proposed in the study is found to be suitable evaluation method for resistance spot weldability.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.193-198
• /
• 2005

The present experiments have been performed for obtaining the melting heat transfer characteristics of micro-encapsulated solid-liquid phase change material and water mixed slurry flow in a circular tube heated with constant wall heat flux. The phase change material having a low melting point was selected for a domestic cooling system in the present study. The governing parameters were found to be latent heat material concentration, heat flux, and the slurry velocity. The experimental results revealed that the increase of tube wall temperature of latent microcapsule slurry was lower than that of water caused by the heat absorption of fusion.