• Journal of the Korean Wood Science and Technology
• /
• 제47권3호
• /
• pp.344-359
• /
• 2019

Effects of various types of zeolite on the catalytic performance of hydrodeoxygenation (HDO) of bio-oil obtained from waste larch wood pyrolysis were investigated herein. Bifunctional catalysts were prepared via wet impregnation. The catalysts were characterized through XRD, BET, and SEM. Experimental results demonstrated that HDO enhanced the fuel properties of waste wood bio-oil, such as higher heating values (HHV) (20.4-28.3 MJ/kg) than bio-oil (13.7 MJ/kg). Water content (from 19.3 in bio-oil to 3.1-16.6 wt% in heavy oils), the total acid number (from 150 in bio-oil to 28-77 mg KOH/g oil in heavy oils), and viscosity (from 103 in bio-oil to $40-69mm^2/s$ in heavy oils) also improved post HDO. In our experiments, depending on the zeolite support, NiFe/HBeta exhibited a high Si/Al ratio of 38 with a high specific surface area ($545.1m^2/g$), and, based on the yield of heavy oil (18.3-18.9 wt%) and HHV (22.4-25.2 MJ/kg), its performance was not significantly affected by temperature and solvent concentration variations. In contrast, NiFe/zeolite Y, which had a low Si/Al ratio of 5.2, exhibited the highest improved quality for heavy oil at high temperature, with an HHV of 28.3 MJ/kg at $350^{\circ}C$ with 25 wt% of solvent.

• Journal of Biosystems Engineering
• /
• 제38권4호
• /
• pp.306-311
• /
• 2013

Purpose: With the ever-rising energy prices, thermal energy heavily consuming facilities of the agricultural sector such as commercialized greenhouses and large-scale Rice Processing Complexes (RPCs) need to cut down their energy cost if they must run profitable businesses continually. One possible way to reduce their energy cost is to utilize combustible agricultural by-products or low-price oil instead of light oil as the fuel for their boiler systems. This study aims to analyze the heavy oil combustion characteristics of a newly developed hot water boiler system that can use both rice husk and heavy oil as its fuel convertibly. Methods: Heavy oil combustion experiments were conducted in this study employing four fuel feed rates (7.6, 8.5, 9.5, 11.4 $l/h$) at a combustion furnace vacuum pressure of 500 Pa and with four combustion furnace vacuum pressures (375, 500, 625, 750 Pa) at fuel feed rates of 9.5 and 11.4 $l/h$. Temperatures at five locations inside the combustion furnace and 20 additional locations throughout the whole hot water boiler system were measured to ascertain the combustion characteristics of the heavy oil. From the temperature measurement data, the thermal efficiency of the system was calculated. Flue gas smoke density and concentrations of air-polluting components in the flue gas were also measured by a gas analyzer. Results: As the fuel feed rate or combustion furnace vacuum pressure increased, the average temperature in the combustion furnace decreased but the thermal efficiency of the system showed no distinctive change. On the other hand, the thermal efficiency of the system was inversely proportionally to the vacuum level in the furnace. For all experimental conditions, the thermal efficiency remained in the range of 80.1-89.6%. The CO concentration in the flue gas was negligibly low. The NO and $SO_2$ concentration as well as the smoke density met the legal requirements. Conclusions: Considering the combustion temperature characteristics, thermal efficiency, and flue gas composition, the optimal combustion condition of the system seemed to be either the fuel feed rate of 9.5 $l/h$ with a combustion furnace vacuum pressure of 375 Pa or a fuel feed rate of 11.4 $l/h$ with a furnace vacuum pressure between 500 Pa and 625 Pa.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.86-94
• /
• 2015

We perform lacquer formation experiments with various combinations of marine fuel oils and lubricant oils. We also investigate the influences of base number (BN) in lubricant oil and sulfur content in fuel oil. A dissolution test with 10% dilute sulfuric acid and pull-off force test are accomplished to distinguish whether the residual layers are lacquering or not. The lacquering layers are dissolved by dilute sulfuric acid and have a strong pull-off force. Moreover, the calcium content detected in the residual layers is compared by energy dispersive x-ray spectroscopy (EDS). More calcium is detected in the lacquer layers than in other residual layers. Distillate fuels containing low sulfur levels are more prone to lacquering when mixed with lubricant oil with a high BN. On the other hand, residual fuels with a high sulfur content do not form lacquer. We investigate the effect of mixture volume ratio. The mixture with higher fuel oil content is more prone to generate lacquer. These experiments indicate that a lubricant with an appropriate BN should be used to prevent lacquer forming on the surfaces such as cylinder liners depending on the sulfur content of fuel oil.

• Korean Chemical Engineering Research
• /
• 제49권4호
• /
• pp.417-422
• /
• 2011

ABS 수지의 반응온도 및 반응시간에 따른 저온 열분해를 연구하기 위하여 ABS 수지의 저온열분해를 회분식 반응기를 이용하여 상압하에서 $425{\sim}500^{\circ}C$ 영역에서 수행하였다. 열분해 시간은 20~80분까지 하였고 열분해로 생성된 성분은 지식경제부에서 고시한 증류성상온도에 따라 가스, 가솔린, 등유, 경유, 중유로 분류하였다. ABS 수지의 열분해에서 80% 이상의 전환율을 얻기 위해서는 반응온도 $500^{\circ}C$ 이상에서 반응시간 60분 이상을 유지하여야 한다. 최종적으로 생성된 분해유는 가스 중유 > 가솔린 > 경유 > 등유 순으로 나타났으며, 온도와 반응시간이 증가함에 따라 중유 및 경유 성분이 늘어났다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.690-695
• /
• 2004

The present study is an investigation on the characteristics of heavy load toque converter by experimental process. To get the dynamic performance, the dynamometer was used with a parameters of speed, torque, oil pressure and oil flux, etc. The torque converter was tested for various input speed, output oil pressure and input oil flow rate. All experiments were investigated in case that the speed ratio is increased. The torque ratio and capacity factor was in inverse proportion to speed. Engine revolution had a more effects at region of low speed ratio. But, the opposite phenomena were represented increase of efficiency. In result of this experiments, the characteristics of torque converter were not influenced by oil pressure and oil flux.

• 한국응용과학기술학회지
• /
• 제35권4호
• /
• pp.985-994
• /
• 2018

바이오중유란 다양한 동 식물성 유지, 지방산 메틸에스테르, 지방산 에틸에스테르 및 그 부산물을 혼합하여 제조된 제품이며, 국내 기력 중유발전기의 연료(B-C)로 사용되고 있다. 그러나 이러한 바이오중유의 원료 조성 때문에 발전기의 보일러로 이송되는 연료펌프, 유량펌프, 인젝터 등의 연료 공급시스템에서 마찰마모를 유발할 경우 심각한 피해를 초래 할 수 있다. 따라서, 본 연구에서는 발전용 바이오중유의 다양한 원료들의 연료특성과 이에 따른 윤활성을 평가하고, 발전기의 마찰마모 저감을 위한 발전용 바이오중유의 연료 구성 방안을 제시하였다. 발전용 바이오중유 원료물질의 윤활성(HFRR)은 평균 $137{\mu}m$이며, 원료물질에 따라 차이가 있으나 $60{\mu}m{\sim}214{\mu}m$ 분포를 보이고 있다. 이 중 윤활성이 좋은 순서는 Oleo pitch > BD pitch > CNSL > Animal fat > RBDPO > PAO > Dark oil > Food waste oil이다. 발전용 바이오중유의 원료 물질 3종으로 구성된 바이오중유 평가시료 5종에 대한 윤활성은 평균 $151{\mu}m$이며, $101{\mu}m{\sim}185{\mu}m$ 분포를 보이고 있다. 이 중 윤활성이 좋은 순서는 Fuel 1 > Fuel 3 > Fuel 4 > Fuel 2 > Fuel 5이다. 바이오중유 평가시료(평균 $151{\mu}m$)는 C중유($128{\mu}m$) 대비 낮은 윤활성을 나타내었다. 이는 발전용 바이오중유가 지방산 물질로 구성되어 있어 C중유보다 파라핀, 방향족 성분 함량이 낮아 점도가 낮고, 산가가 높기 때문에 산성 성분에 의한 윤활막 형성 저해에 따른 것으로 판단된다. 따라서, 적정 수준의 마찰마모 저감을 위해 윤활성을 증가 시킬 수 있는 바이오중유의 원료로서 Oleo pitch, BD pitch를 60% 이상 함유할 경우 연료 제조 시 윤활성 증가가 예상된다.

• Tribology and Lubricants
• /
• 제31권1호
• /
• pp.28-34
• /
• 2015

This paper addresses the problems of using anti-freeze lubricants for different machines that must function at extremely low temperatures during winter operation in the Republic of Sakha (Yakutia). We discuss the possibility of obtaining anti-freeze base oils from Talakan crude oil, an area with major oil and gas deposits of the Republic of Sakha, and also provide the trade and technological classification of Talakan crude oil. We propose two different schemes for processing Talakan crude oil: the fuel scheme (obtaining light and heavy fractions as a fuel oil) and the base oil scheme (obtaining light fractions and base oils). We investigate the influence of pour point depressants on alkyl-methacrylate base on the low-temperature properties of the fractions obtained from Talakan crude oil and Korean base oils, and establish the optimal concentration of pour point depressants. We compare the properties of these fractions with the low-temperature properties of Korean base oils and find that the commercial oil "Ravenol 0W-40" provides optimistic results. We obtain oil with a pour point of minus $50^{\circ}C$ and a viscosity index greater than 100. The Design of Experiment was used to establish the optimum composition of the pour point depressants and the base oil S-8 to obtain lubricant oil with a kinematic viscosity of 17 cSt, viscosity index of 208, and a pour point of minus $64^{\circ}C$.

• Korean Chemical Engineering Research
• /
• 제50권2호
• /
• pp.223-228
• /
• 2012

ABS와 폴리에틸렌(Polyethylene, PE) 및 ABS-PE 혼합물의 저온열분해를 회분식 반응기를 이용하여 상압 및 $450^{\circ}C$에서 실행하였다. 열분해 시간은 20~80분까지 하였고 열분해로 생성된 성분은 지식경제부에서 고시한 증류성상온도에 따라 가스, 가솔린, 등유, 경유, 중유로 분류하였다. ABS와 PE의 혼합 폐플라스틱의 열분해 전환율은 PE의 함량이 증가할수록 증가하는 것으로 나타났다. 열분해생성물의 수율은 PE의 함량이 높을수록 중유 > 가스 > 가솔린 > 경유 > 등유 순으로 회수되었다.

• 한국기계연구소 소보
• /
• 제4권1호
• /
• pp.89-97
• /
• 1981

• 한국수소및신에너지학회논문집
• /
• 제21권5호
• /
• pp.452-459
• /
• 2010

This study is aimed to investigate changes of combustion characteristics and heat efficiency when syngas from gasification process using low-rank fuel such as waste and/or biomass is applied partially to an industrial boiler. An experimental study on syngas co-combustion was performed in a 0.7 MW (1 ton steam/hr) water tube boiler using heavy oil as a main fuel. Three kinds of syngas were used as an alternative fuel: mixture gas of pure carbon monoxide and hydrogen, syngas of low calorific value generated from an air-blown gasification process, and syngas of high calorific value produced from an oxygen-blown gasification process. Effects of co-combustion ratio (0~20%) for each syngas on flue gas composition were investigated through syngas injection through the nozzles installed in the side wall of the boiler and measuring $O_2$, $CO_2$, CO and NOx concentrations in the flue gas. When syngas co-combustion was applied, injected syngas was observed to be burned completely and NOx concentration was decreased because nitrogen-containing-heavy oil was partially replaced by the syngas. However, heat efficiency of the boiler was observed to be decreased due to inert compounds in the syngas and the more significant decrease was found when syngas of lower calorific value was used. However, the decrease of the efficiency was under 10% of the heat replacement by syngas.